Determine the support reactions of the following structure using force method. Only consider the bending moment effect

Q: Q4) Determine the force in members JI, IC, and CD of the truss. State if the members are in tension…

A:

Q: Fluid Properties A hydraulic lift consists of a 40 cm diameter ram and slides in a cylinder of…

A:

Q: Fluid Properties A hydraulic lift consists of a 40 cm diameter ram and slides in a cylinder of…

A: Diameter of the ram d=40 cm,Diameter of the cylinder D=40.020 cm,Kinematic viscosity v'=0.025…

Q: The absolute maximum Bending Moment in a simply supported beam of span 20 m due to a moving udl of 4…

A: Simply supported beam of 20m span lengthMoving udl of 4t/m span over 5mTo findAbsolute maximum…

Q: Problem 2 An A36 channel section is used as a purlin in a roof system with spacing of trusses at 4.5…

A: Dead load, DL = 1.2 kN/m2Live load, LL = 1.4 kN/m2Take windward, L= 0.72 kN/m2A36 steel grade - fc =…

Q: Calculate Superelevation for a horizontal cure with redius 300mand wides 8m. the design speed 50…

A: Radius of curve (R) = 300m Width (B) = 8m Design speed (V) = 50 km/h Centrifugal ratio = 1/10…

Q: A precast concrete pile of size 50 cm x 50 cm is to be driven into clay strata whose unconfined…

A:

Q: A bar specimen of 36 mm diameter is subjected to a pull of 90 kN during a tension test. The…

A: Given-Diameter d=36 mm,Change in diameter d'=0.0046 mmPull P=90 kN,Gauge length L=200 mm,Increase in…

Q: How do modern methods differ from more traditional ones? Where do these two methods part ways?

A: Modern methods are approaches, procedures, or practises that have originated or evolved as a result…

Q: What is a secure hazardous waste landfill? List four ways to reduce your output of hazardous waste.

A: IntroductionA landfill is a location set aside for the disposal of solid waste by burying it under…

Q: A municipal wastewater treatment plant processes an average flow of 5000 m³/d. A primary clarifier…

A: Average flow Q=5000 m3/dEfficiency of primary clarifier=60% at average flow.To Find-The value of…

Q: If we want to have a generator burn methane and produce 2.5 kWh, how much COD is needed, assume a…

A: Energy outputGenerator efficiency, To find: The required amount of COD.

Q: When it comes to solid modelling, a designer can really go the whole nine yards by sculpting and…

A: Designers can go beyond just mixing lines in solid modeling to produce more complex and lifelike…

Q: c. If a foundation load of 75 kN/m² is planned and testing of sample of the clay layer has shown the…

A:

Q: Calculate Superelevation for a horizontal cure with redius 300mand wides 8m. the design speed 50…

A:

Q: Consider a free-flowing structure with a gate, a rectangular cross-section, and properties given in…

A: The properties of a rectangular cross-section are:-Crest height = 0.2 m Width = 2.1 m Gate opening =…

Q: Gusset plate Column Pin diameter = Steel plate Pin 80 mm 16 mm 10 mm thickness one 40 kN For the pin…

A: Determine 1. Normal stress acting on the gross area. 2. Normal stress acting on the net area. 3.…

Q: The car has a speed of 15 m/s at the top of a hump when the driver applies the brakes, causing a…

A:

Q: The roof of a building is subjected to the wind force shown be the horizontal (x) component of the…

A:

Q: A faucet is shown on the figure below. A force of P = 1100 lb is exerted : t both ends of the faucet…

A:

Q: For the vertical flexural member shown, determine the maximum shear stress in MPa at section K, as…

A: To determine: Maximum shear stress at section K

Q: Determine the distance to the centroid of the area.

A:

Q: On a railway track with rail lengths of 12.8m sufficient depth of ballast needs to be provided.…

A:

Q: A given cohesionless soil has emax = 0.85 and emin = 0.50. In the field, the soil is compacted to a…

A: For cohesionless soil:Void ratio:The mass density of soil, at ta 8 % water contentThe mass density…

Q: A soil sample following results: Standard sieve No: TOATE RE 4 10 20 40 100 200 was analyzed Pan…

A: IntroductionA sieve is a tool or equipment used in soil engineering to measure the particle size of…

Q: A 300mm x 400mm RC column is reinforced with b vertical bars, three bars in each 300mm face.…

A:

Q: Determine the vertical displacement of joint A. Each bar is made of steel and has a cross-sectional…

A:

Q: To irrigate a strip of area of size 100 m × m, the time taken is 50 minutes. Assuming average depth…

A: Irrigation area = 100m²Time taken to irrigate the land= 50min. = 50×60 secAverage depth of water =…

Q: Solve for the support reaction of the following problem. kindly show your solutions below. thank you

A:

Q: Using the force method, calculate the bending moment at B for the statically indeterminate frame…

A:

Q: A pumping test was made from a well in a permeable layer underlain by an impervious stratum. When…

A: Given that for a pumping test from a well in a permeable layer underlain by an impervious stratum, q…

Q: If the irrigation efficiency is 80%, conveyance losses are 20% and the actual depth of the watering…

A: Irrigation efficiency-To Find-The depth of water required at the canal outlet (D).

Q: 4a. Draw the quantitative (i.e. including values) influence line for the vertical reaction at E. A 4…

A: To determine ILD for reaction at EILD for an internal moment at CILD for shear just to the left of…

Q: Q.1 A body is subjected to two normal strains of magnitude <= 0.004 and , = 0.002. The shearing…

A:

Q: Compute the discharge rate through the gate shown below for y₁ equal to 2.0 m and y, equal to 0.65…

A: y1  =2.0 m y2 =0.65 mGate width  B = 1.0 mHead loss hL  = 0 mTo calculate Discharge   Q = ?

Q: Q Calculate the diameter and discharge of a circular sewer laid at a slope of when it is running…

A:

Q: uct on th 31 SITUATION 1: A stratified soil consists of the following layers: Layer 1: Thickness, H₁…

A:

Q: Draw the shear and moment diagrams for the beam below. Label the maximum magnitude moment and…

A:

Q: 2) You are responsible from the planning and design of a water reservoir. As shown below, the…

A:

Q: Question 1 If the coefficient of active earth pressure is 1/3, then what is the value of the…

A: Coefficient of active earth pressure Ka=1/3To Find-The value of the coefficient of passive earth…

Q: What is the total thickness of a wall having 3/8 inch first siding, 2/8 inch rough siding, 3 3/4…

A: Thickness of first siding, Thickness of rough siding, Thickness of studs, Thickness of lath,

Q: The driver of a vehicle approaching a signalised intersection at a speed of 40 kmph applied brakes…

A: Speed u=40 kmphAmber time=4 sReaction time=1 sTo Find-The average friction coefficient developed.

Q: (a) y = i in. |₂= i in.4 S= i or 3

A:

Q: An axial member consisting of two polymer bars is supported at modulus of 29 GPa. Bar (2) has a…

A:

Q: Calculate the pile's allowable bearing load using the corrected SPT values at various depths given…

A:

Q: Not the ȳ. I NEED THE y for the top and bottom flange? how did they get the values 4.917 and 11.58

A: Equal area axis:Let yt be the equal area axis from the top flange. Then the total area is calculated…

Q: A soil particle has the following grain characteristics Size (mm) Percent Fine 2.0 0.050 0.0075 <…

A:

Q: The point loads are placed at the fixed positions shown in the figure and they are live loads. A K a…

A: Since the condition for each subpart is varying, the first part will be calculated. Please submit…

Q: A pipe culvert 45 ft long extends between two reservoirs as shown below. The difference in the water…

A:

Q: What positive effects does architecture have on society? Compare a project with architecture against…

A: Architecture refers to the art, science, and practice of designing and constructing buildings and…