Consider the plate subjected to the four external loads shown. Calculate an equivalent force couple system with the force acting thru the bottom left corner of the rectangle. The 50N loads are inclined at 45 degrees with the vertical. SON floow 200mm 150mm 50mm 145 200N 50N

Consider the plate subjected to the four external loads shown. Calculate an equivalent force couple system with the force acting thru the bottom left corner of the rectangle. The 50N loads are inclined at 45 degrees with the vertical. SON floow 200mm 150mm 50mm 145 200N 50N

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 1.) What is the vertical reaction at A and B? 2.) What is the horizontal and moment reaction B 3.)…

Q: Determine the greatest A punch press has the cast steel frame shown in Figure force P that can be…

Q: (4) Two kids (200 N each) are balanced on a seesaw. Plane a-a (containing Point A) is just left of…

A: Data given Find : combined state of stress at two points A and B

Q: 3. Design a column of wide flange section W for the member (DE) of the frame shown below The frame…

A: Given data: Axial load on the column, P=2500 kN Effective length factor, Ky=1.0 and Kx=2 The column…

Q: Determine the reactions at the supports for the beam shown in Fig.

A: Given : We are asked to determine the reaction at the supports ?

Q: A tracer takes 100 days to travel from Well-1 to Well-2 which are 100 m apart. The elevation of…

A: Given- Distance D=100 m, Time T=100 days, Head difference h = 3 m, Porosity n=15% = 0.15, It is…

Q: A w = 5 kips/ft 1.61 24' B 20 kip. ft I 6- 6 12- C

Q: (2) A square member (400mm x 400mm) sustains an internal shear force of 150 kN and an internal…

Q: | 2a. The following data was obtained from Liquid Limit Test conducted at a Soil Lab. Using the data…

A: Given data, Plastic limit = 22 Liquid limit will be the water content at 25 blows.

Q: 2. The porosity of a soil sample is 35% and the specific gravity of its particles is 2.70. Solve the…

Q: Solve the shear and bending moment diagrams, and qualitative shape of each structure 2. A 30 kN/m T…

A: Given Hinges are present at B and D . Load of 30 KN/ m is acting on 34 length of beam .

Q: A line was determined to be 2538.45 m when measured with a 45m tape supported throughout its length…

Q: Design Column AB of the frame shown below for a design load of 3000 kN. Assume that the column is…

A: Answer We need to find a member whose design strength for column AB is greater than the design load…

Q: The modulus of elasticity of concrete (Force/Area) is 13 GN/m^2. Determine its US Customary units…

Q: shear and moment functions, V(x) and M(x) and draw the shear and moment diagrams (graphs).

Q: 5. A tensile test was done on a magnesium sample of original diameter and original length of 12mm…

A: To plot the stress v/s strain curve and to find the required parameters Note: as per the answering…

Q: 1.5 m 1 m 2 m B 5 kN -4 m C P₁ -5 m D VP2 -4 m E

Q: Explain the bellow statements as it relates to design process for renovation Providing a visual…

A: Renovation is characterized as any alteration to an existing structure, or to a part of a structure,…

Q: Using relations among load, shear, and bending moment solve problem 7.29: For the beam and loading…

Q: lok 51 tidlastbar гок UT

Q: The area of the plan of an old survey plotted to a scale of 10 m to 1 cm measures 97.6 sq. cm as…

A: Given- Scale S=10 m to 1 cm, Measured area = 97.6 cm2, Original length = 9.8 cm, It is needed to…

Q: Problem: Draw shear and moment diagrams and show detailed computations by area method. Determine…

A: Shear force is defined as the sum of all forces that are acting on one of the sides of the beam or…

Q: 5. Determine the force in members BC, EC and ED of the truss and state if the members are in tension…

Q: What are three (3) major global environmental concerns facing today's environment. What sort of…

A: Solution:- Given data:- It is asked to what are three major global environmental concerns facing…

Q: + High-strength bolts are used in the construction of many steel structures. For a 1-in.-nominal-…

Q: Determine the reactions at the fixed support of the structure shown in equilibrium. Hint: A fixed…

Q: What are three (3) major global environmental concerns facing today's environment. What sort of…

A: Three major global environmental issues: 1. Water pollution 2. Air pollution 3. Solid waste…

Q: A flat circular plate, 1.25 m diameter is immersed in sewage water (density 1200 kg/m³) such that…

A: Given data : Diameter of circular plate = 1.25 m Density = 1200 kg/m3 Greatest depth = 1.50 m Latest…

Q: The perception - reaction time for a vehicle travelling at 90 km/h, given the coefficient of…

A: Given data- Design speed V=90 km/h, f=0.35, SSD=170 m, g=9.81 m/s2, To Find- Perception reaction…

Q: A small turbine is run by water from a reservoir, as shown. Both the pipe leading to and away from…

A: Given data: Diameter of the pipe, D= 0.6 ft Velocity, V=10 ftsec The volume flow rate from the…

Q: RECTION: Draw the axial, shear, and bending moment of the following rigid fram d show the necessary…

Q: For the figure shown below, determine the slope at B and deflection at D using VIRTUAL WORK METHOD.…

A: ###Using method of Virtual work method## ###Calculation of slope at B and Deflection at D##

Q: 10' 10' B 30 kips A 14' w = 2 kips/ft + -14'- C

Q: Determine the reactions for the structure. T B

A: Given : Determine the reactions at supports ?

Q: 2.3 The floor system of a gymnasium consists of a 130-mm-thick concrete slab resting on four steel…

Q: Using the influence lines, draw the detailed influence lines of shear and moment at the midpoint of…

A: Given data:

Q: 4m A E -4m- 24 KN B D -4m- 12 kN C

A: Summation of all forces in X- direction equal to zero .. similarly in Y direction and calculate all…

Q: Q-A vertical wall of height 5 m retains a soil having ysat = 20 kN/m³, and p = 30°. Uniform…

A: Given data- Height of vertical wall Z = 5 m, Saturated unit weight γsat=20 kN/m3. UDL q=12 kN/m2,…

Q: Where did 1161 came from at the last part of computation of the deflection at D. Because I put the…

A: Given Data E = 16500 MPa I = 105 × 106 mm4 Find slope at B and deflection at D using virtual work…

Q: What would be maximum possible discharge through a 2.5 m wide rectangular channel. If specific…

A: Given- Width B=2.5 m, Specific energy E=1.2 N-m/m,

Q: For the beam supporting the loads, determine the slope and deflection of the free end using AREA…

Q: Two tangents converge at an angle of 30° And is connected by a reverse curve of equal radii. The…

A: Engineering work called civil surveying includes examining and documenting information about a piece…

Q: A 15-ft beam simply supported at the ends carries a concentrated load of 9000 lb at midspan. Select…

A: Given : Span of beam = 15 ft Concentrated load = 9000 lb ( at midspan ) Allowable stress = 18 ksi…

Q: 1. For the assembly shown, determine the displacement of point B and D as the load of 50KN is…

Q: Uniform Flow Q.10 The sequent depths in a hydraulic jump formed in a 4.0m wide rectangular channel…

A: Given- Sequent depths- y1=0.3 m,y2=1.2 m, Width of channel b = 4 m, It is needed to find the…

Q: An elevated cylindrical water storage tank is shown in the figure. The tank has inner diameter of…

Q: Two reservoirs are connected through a homogeneous and isotropic aquifer having hydraulic…

A: Given data- Hydraulic conductivity K=25 m/day, Porosity n=0.3, Length L=2 km=2000 m, To Find- The…

Q: A rectangular block of wood, floats with one face horizontal in a fluid (RD = 0.9). The wood's…

A: Given : RD = 0.9 Wood density = 750 kg/m3 To Find : Determine the percentage of the wood which is…

Q: For the propped beam shown in Fig. the maximum positive bending moment. 1400 N/m 2 m dob Figure ,…

A: Given data : Determine the prop reaction and the max, positive bending moment ?

Q: The drawing represents a loaf of bread with a slice shown x inches from the left-hand end of the…

A: Given data- A drawing representing a loaf of bread with a slice shown x inches from the left-hand…

Question

Consider the plate subjected to the four external loads shown. Calculate an
equivalent force couple system with the force acting thru the bottom left corner of the
rectangle. The 50N loads are inclined at 45 degrees with the vertical.
SON
floow
200mm
150mm
50mm
1459
2000 500

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

3/98 Each of the three uniform 1200-mm bars has a mass of 20 kg. The bars are welded together into the configura- tion shown and suspended by three vertical wires. Bars AB and BC lie in the horizontal x-y plane, and the third bar lies in a plane parallel to the x-z plane. Compute the tension in each wire. B 600 mm 1200 mm A 30⁰! 1200 mm PROBLEM 3/98 600 mm -y
From the bracket connection shown. 1. Which of the following gives the stress due to axial load. a. 62.07 MPa b. 75.56 MPa c. 52.89 MPa d. 19.34 MPa 2. What is the value of ‘b’ that will make the maximum stress due to moment equal to that due to axial load? a. 150 mm b. 200 mm c. 250 mm d. 300 mm 3. What is the eccentricity? a. 300 mm b. 250 mm c. 150 mm d. 196.78 MPa
The copper pipe has an outer diameter of 50mm and an inner diameter of 30mm, If it is fixed at A and three torques are applied to it as shown, solve the shear stress at section 2. A 200mm 250mm 300mm 30 N-m 20 N-m 80 N-m O 0.94MPA O 4.68MPA O 187MPA O 2.81MPA
10. The hoisting beam assembly shown is supported by two 20- mm-diameter bolts at A and a 150 mm x 200 mm plate at B. In this problem, a = 1.2 m and b = 2.8 m. If the allowable tensile stress of the bolts at A is 112 MPa, which of the following gives the maximum safe value of W in KN? A. 45 C. 30 B. 60 D. 15 ZEIT 0 a BEEN H 8804 pe (cAPlate B to tried man 11 of 1911 b bell 110 mb llame lis To 102 W 20-102 bugil noitsuta
Quiz/ find the angle of rotation of the free end for the beam shown, then find the max sheaving stress If you know GAI = 28 GN/m² Gst=83 GN1m² GBV = 35 GN/m² Aluminum steel Bronzer Do d=100mm 3m d=75mm 2m 1.5m 1.5 KN.m
* A For the RIGID beam shown, find the :deflection at point B 2m B 3m C 3m 50 kN ID +0.025 m O -0.025 m O Non of them O -0.125 m O +0.125 m O No deflection O
Strain in rods is zero prior to applying load Determine load P such that the axial stress in the steel pipe is 200 MPa P Imm GAP RIGIO PLATE .6m B RIGID SUPPORT 30 mm x 30 mm. AL BAR E = 73 GPA 100 mm E = 200 G PO A B A ØSTEEL PIPE w/ 5mm WALL
Classify the structure is statically determinate (write SD), statically indeterminate (Write only the degree of indeterminacy say SI 2 degrees; i.e. 2), or unstable (write U). Blank 1 ... Blank 1 Add your answer
Problem 12 A plate is fastened to a fixed member by four 16mmP rivets arranged as shown. Compute the maximum shearing stress developed in the rivets. 30KN 100mm spacing 30KN
1) DETERMINE TENSILE BENDING THE CROSS-SECTION BELOW. SOKN 20KN/m 3m THE MAXimum STRESSES OF THE B 30 кн/т Gm COMPRESSIVE Ано THE BEAM BEAM GIVEN 150MM SHOWIN 30mm 180mm 30mm
Determine the principal stresses acting at the 1 section using Mohr circle 150mm 5mm 5kN 60° 180mm 6mm 8mm 2 m 3 m 3 m 200mm
Consider the truss structure and the loading given below. a) Compute the average axial stress on member AB, b) compute the average shear stress at the pin of connection A. d- 20 mm 600 mm 50 mm -S00 mm 60 kN 25 mm | I 20 mm 30 mm I20 mm 25 mm TOP VIEW OF MEMBER AB d = 30 mm