only HANDWRITTEN answer needed ( NOT TYPED) Consider the frame shown which is of height, H, 5.5 m and bay length X, of 4.5 m.EANB50kN3 bays of Xm eachAFNumberHmDDetermine the force, in kN, acting in member BF.Answer to 4 decimal places presenting a compressive force should be shown as a negative force while a tensile force is a positive force.

A truss is given with a 50kN point load at B. To determine the force in member BF. Section…

Consider the frame shown which is of height, H, 5.5 m and bay length X, of 4.5 m. F ANH B 50kN 3 bays of Xm each E Hm Determine the force, in kN, acting in member BF. Answer to 4 decimal places presenting a compressive force should be shown as a negative force while a tensile force is a positive force.

Consider the frame shown which is of height, H, 5.5 m and bay length X, of 4.5 m. F ANH B 50kN 3 bays of Xm each E Hm Determine the force, in kN, acting in member BF. Answer to 4 decimal places presenting a compressive force should be shown as a negative force while a tensile force is a positive force.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1-55 A planar truss system has the dimensions shown in the figure. Member AE is continuous and can resist bending. All joints are pinned. Determine the diameter required for tension member AB to carry the applied force at A. The allowable stress is 40 ksi. photo of the diagram is attached with the question.
1. The figure shows a truss which is a pin connected at C and supported by a roller at D. It carries a vertical loads of 200kN and 100KN at joints A and E respectively. Use Method of Joints. 4m 2m 200 kN 100 kN 6m 3m O Calculate the force in member DE. ® Calculate the force in member BE. ® Calculate the force in member BC.
a. The beam weighs 3600N. Draw the V and M diagram. b. Assume we do not know the weight of the beam the solid steel bar has a square cross section of side b and is supported as shown. We know that density of steel is 7860 kg/m, calculate the dimension b for which the maximum normal stress due to bending is 50 MPa. A C -1.2 m-1.2 m- D 1-1-1 B -1.2 m- b
Determine the force in each member of the bridge truss shown. State whether each member is in tension or compression. 100KN H K 4m L. A 3m 3m 3m 3m E B C
The steel truss (E =200 GPa) shown in figure below has a cross-sectional area of 1920 mm². Determine: a. The largest allowable load F if the change in length of member BD is not to exceed 1.6 mm and a factor of safety of 2.5. b. The displacement of support D due to the load calculated in part a. 5m 6m A C F
QI: Determine the forces in all members for the truss shown below and state whether the members in tension or compression? D 5m Sm Sm B. A. 12m 12m P.
Problem 2: Determine the force in member BC, CF and FE. State if the member are in tension or compression. Show all your work to receive full credit. (Hint: It is not needed to find the reaction forces at A and G if you use the Method of Joints). 150 N 150 N 100 N
A simply supported beam AB is loaded as shown in the figure. CDE is a rigid member.Draw SFD
The steel is supported by the steel tie rod in AB beam B. Steel connection tension rod is placed 2 meters to the left of B and C sliding bracket is placed and P is loaded between AC It is. By ignoring the weights of beams and connecting rods, they can be determine the largest P load it can carry. The diameter of the BD rod is 16 mm. E = 200GPa I = 150x106mm4
M Three strips each 10mm x 30mm in cross section built up laminated plastic beam of square cross section glued together as shown. The beam has a total weight of 10 N/m and with t10 mm span length L = 360 mm. 10 mm 30 mm 10 mm 30 mm L a. calculate the moment M that may be placed at the right support if the allowable shear stress in the glued joints is 0.3MPa ( N-mm) b. by any method, find the maximum deflection of the beam c. find the location of the maximum deflection of the beam ANS: ANS: ANS:
The cross-sectional area of each member of truss shown below is A-400mm² and E-200GPa. Determine the vertical displacement of joint C if a 4kN force is applied to the truss at C 4 kN 4 m 4 m 3 m
Determine the force in member BE of the Howe roof truss shown in Ibs. P1 = 814 kN and P2 = 1,124 kN. Write numerical value only and in 2 decimal places. P2 P2 P2 D P1 P1 6 ft B 6 ft н Ao E G 8 ft 8 ft- 8 ft→ 8 ft- -8 ft-