Consider the circuit below in which the dependent current source depends on the current it, the current through R1. Given 10 = 90 mA, i1 = 15 mA, R1 = 400 ohms, and R2 = 50 ohms, 311 V3 10 R1 9. Find the current through R2. On your paper, you must show how you arrive at the answer in detail in order to receive any credit a 30 mA b. 45 mA c. 15 mA d. 60 mA e. Write in an answer R2 www HH

Consider the circuit below in which the dependent current source depends on the current it, the current through R1. Given 10 = 90 mA, i1 = 15 mA, R1 = 400 ohms, and R2 = 50 ohms, 311 V3 10 R1 9. Find the current through R2. On your paper, you must show how you arrive at the answer in detail in order to receive any credit a 30 mA b. 45 mA c. 15 mA d. 60 mA e. Write in an answer R2 www HH

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter7: Parallel Circuits

Section: Chapter Questions

Problem 3PP: Using the rules for parallel circuits and Ohmslaw, solve for the missing values....

See similar textbooks

Similar questions

c). write the current equation for the circuit below 60 mA 20 mA 14 Is 40 mA 30 mA Determine the missing currents from the equation in c).
INSTRUCTIONS: Solve the following problems. Show and COMPLETE solutions. Draw all CIRCUIT DIAGRAMS or the equivalent circuit (dummy circuit) as the case may be. Write your solutions on sheet/s of short bond paper. A battery is to consist of 20 identical cells. The emf of each cell is 1.5 V and the internal resistance is 0.20 ohm. This battery will be used to supply power to a 10 ohm lamp. Determine the current on the lamp if:1. The 20 cells are connected in series 2. The 20 cells are connected in parallel 3. The 20 cells are arranged 5 cells in series in 4 parallel rows.
In the circuit in the figure, the value of the current I1 is found as ……….. µA (microampere).
need fast. show circuit diagram
150 100 + VA- a -4V AVA -7V 81. B b Figure 2 shows a simplified model of a gas-discharge lamp. One characteristic of these lamps is that they exhibit negative resistance; in other words, as current increases the voltage drops further, making such lamps inherently unstable. As such, a current-limiting ballast is required. For the connection shown in the figure: 1. Find the equivalent Thevenin circuit of the lamp. 2. Find the ballast resistance needed to limit the current drawn from a 24-volt source to 6 amperes.
What is the load current for the circuit shown in the figure? Please choose one: a. 9.0 mA b. 7.5 mA c. 3.0 mA D. 6.0 mA
Shown in the figure is a schematic of a power electronics circuit. a) Identify the power semiconductor devices included in the circuit b) sketch their symbol with terminal identification c) explain the function of power semiconductor devices included in the circuit 120kn 240 V 60 Hz 2N2574 ODeg 1.0kn ECG6412 :100nF
%3D ) Drurde (l0o1102 and (o
Which of the following statements are correct for the circuit below? Thanks to the capacitors I – C1 and C2, the voltage gain of the circuit increases. II – Capacitors C1 and C2 are coupling capacitors and provide an isolation function between AC and DC voltages in the circuit. Thanks to the III – RE resistor, the voltage gain of the circuit increases. Thanks to the IV – RE resistor, the stability of the circuit increases. The V – C3 Capacitor is a bypass capacitor and prevents the loss of voltage gain. Capacitor VI – C3 is a coupling capacitor and has no effect on the voltage gain in the circuit. VII – As the value of the source internal resistance Rs increases, the voltage gain decreases. VIII – The voltage gain decreases as the value of any RL load to be added to the circuit increases
How do we approach this problem? please and thank you. Also how do we know when to use kvl and kcl in a circuit
The circuit below(left) displays a schematic diagram of a battery. The voltage measured by U1 is called the terminal voltage given R1 = 1 ohm. In the circuit below(right), the terminal voltage of each of the battery-resistor combination is VT = 1.5 volts. Find the percentage of voltage loss of the battery due to the internal resistance R1.
The circuit below(left) displays a schematic diagram of a battery. The voltage measured by U1 is called the terminal voltage given R1 = 1 ohm. In the circuit below(right), the terminal voltage of each of the battery-resistor combination is VT = 1.5 volts. Find the current passing through R1, R3, R5