Compute the normal acceleration when the boy reaches the bottom of the profile. (m/s^2) Weight of the man 67.50kgVelocity Equation = V = 20(6.33 - y): where y is the height measured from the x-axis%3D%3DY.y=0.055x+4.356.33m

Answered: Image /qna-images/answer/a8dc2e32-bcbc-483e-88b5-d8381d74607d.jpg

Answered: Compute the normal acceleration when…

Engineering

Mechanical Engineering

Compute the normal acceleration when the boy reaches the bottom of the profile. (m/s^2)

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter9: Moments And Products Of Inertia Of Areas

Section: Chapter Questions

Problem 9.13P: Figure (a) shows the cross section of a column that uses a structural shape known as W867...

See similar textbooks

Related questions

Q: 2.52 x 106 L/hour of steam enters an adiabatic turbine at 19 MPa, 700°C and 150 m/s, and leaves at…

Q: A) A DC motor driven pump running at 100 RPM delivers 30 L/sec of water at 40C (d = 992.3 kg/m3 )…

A: Given data: N1=100 RPMQ=30 L/s=30×10-3 m3/sρ=992.3 kg/m3η=60%H1=27 mH2=36 m Need to determine the…

Q: 20- Air enters a nozzle steadily at 280 kPa and 77°C with a velocity of 50 m/s and exits at 85 kPa…

Q: Problem 3) Determine the reactive forces at A and B. 14 kN E 2 m 16 kN F 2 m A B.

A: From equilibrium conditions for above fbd

Q: Fill in the blanks a) b) - 1 attachment A 25-kg projectile is fired vertically upward from the…

Q: The torsional assembly shown in figure below consists of a solid bronze (G aluminum alloy (G 45 GPa)…

Q: At the instant shown in Figure 2, car A is moving at a constant speed v. = 70 km/h while truck Bis…

Q: A block sits on a plane, and there is friction between the block and the plane. The plane is…

A: Graphical representation of forces may be applied externally, reactions ( normal force, tension,…

Q: A shell and tube heat exchanger has the cross-section shown below. Crude oil (specific gravity, sg =…

A: To Calculate : 1). Hydraulic Diameter in mm. 2). Reynolds number of Crude oil. 3). The flow regime.…

Q: Instructions: Draw the line of action of the following muscles using free body diagrams using blue…

A: Draw the free-body diagrams of muscles with fulcrum, effort force, resistance force and lever…

Q: A closed pipe 3 ft. long, compute the 6th harmonic if air temperature is 80℉.

Q: A two - stage ammonia compression refrigerating system with flash intercooling and flash gas removal…

A: Given Data The mass flow rate is:m˙1=0.2 kg/sec The evaporating temperature is:T=-30°C The…

Q: Current Attempt m ogress For what value M of the clockwise couple will the horizontal component A,…

Q: Bar (1) has a length of L1 = 2.4 m, and bar (2) has a length of L2 = 0.63 m. Initially, there is a…

Q: A small ship capable of making a speed of 6.8 knots through still water maintains a heading due east…

Q: The top of the folding workbench has a mass of 58 kg with mass center at G. Calculate the magnitude…

A: Given data mass of workbench (m) = 58 kg To determine the magnitude of the force supported by the…

Q: The air in an insulated, rigid compressed-air tank whose volume is 0.5 m3 is initially at 2400 kPa…

Q: A fluid is pumped at a rate of 0.00156 m3/s through a 0.025-m-diameter pipe to fill a water tank as…

Q: The device shown is used for determining the shear strength of the wood. The dimensions of the wood…

Q: For a 34.4 mm diameter smooth pipe, calculate the threshold velocity (m/s) and corresponding flow…

Q: What is the specific enthalpy (kJ/kg) and specific entropy (kl/kg-K) of a steam with a specific…

Q: 7. Calculate the linear density of atoms along the [111] direction and the planar density of atoms…

Q: An aircraft has a total mass of (1.26x10^2) kg and a wing area of (2.3000x10^1) m². It operated with…

A: Chord line is the line joining the leading and tailing edges of the airfoil. Profile line is defined…

Q: The galvanized iron system has two pipe diameters, BC at 6 in. and CE at 3 in. The gate valve at F…

A: Given Data The diameter of pipe BC is:dBC=6in=0.5 ft The diameter of pipe CE is:d=3 in=0.25 ft The…

Q: Determine the moment of inertia about an axis perpendicular to the page and passing through the pin…

Q: Assume you are bending a 3/16” thick rolled plate of Al 6061-T6 at a 90-degree angle. The initial…

A: Solution: Given Data: t=316"Ri=0.35" Note: Yield strength of Al 6061-T6 is: Sy=35000 psi Young's…

Q: The pressure and temperature of air change from (6.5000x10^0) bar to (2.000x10^0) bar and from…

Q: Explain major impact all major losses through the pipes.

Q: The air in an insulated, rigid compressed-air tank whose volume is 0.5 m3 is initially at 2400 kPa…

Q: Calculate the higher and lower heating values of octane, C3H18, by using the stoichiometric reaction…

A: The enthalpies of formation for the following compounds can be given as: C8H18 → -250.0 kJ/mol O2 →…

Q: Find the general solution for the following first order D.Es? b) x*dy + (y? - xy)dx 0 d) (x + xy -…

Q: Q=2000J Tout=? V(m/s) D=0.1m air Air at (3.050x10^2) K is entering in a circular pipe at 101325 Pa…

A: Given data Temperature at entrance = T1 = 305.0 KPressure at entrance = P1 = 101325 PaVelocity at…

Q: A rectangular plate (Figure) is subjected to a vertical force applied at point B and to a couple of…

A: The magnitude and line of action of the resultant force when β= 40∘: Magnitude of the resultant…

Q: ᴀ ꜱᴜᴘᴘʟʏ ᴛᴀɴᴋ ʜᴀᴠɪɴɢ 14ᴍ ʟᴏɴɢ ᴀɴᴅ 1.7ᴍ ᴅɪᴀᴍᴇᴛᴇʀ ɪꜱ ᴜꜱᴇᴅ ᴛᴏ ꜱᴛᴏʀᴇ ꜰᴜᴇʟ ᴏɪʟ ᴡɪᴛʜ 34° ᴀᴘɪ ᴀᴛ 110 °ᴄ. ɪꜰ…

Q: Two airplanes are performing at an air show. Plane A travels along the path shown and, for the…

Q: The transmitted torque of a 100 mm steel shaft is 5 kN-m and the maximum bending moment is 3 kN-m.…

Q: The pressure and temperature of air change from (7.000x10^0) bar to (1.50x10^0) bar and from…

Q: Design a compression coupling for a shaft to transmit 1300 N-m. The allowable shear stress for the…

Q: SC- 0.92 Find: gas W> loN fresure, P;? O- 1cm Sm water 2m 1,5m

Q: 2. There are received 90,000 kg/h of steam at 2.156 MPa, 481 ° C by a Rankine cycle and Rankine Eng…

Q: The 700 N skier is schussing on a 25° slope. At the instant shown, he is moving at 20 m/s. The…

Q: Air at (4.70x10^2) K flows out of a circular pipe at 101325 Pa as shown in Figure. The mass flowrate…

A: Given data:

Q: A centrifugal pump operating at sea level develops 50 m of head at 1,200 rpm. It is used to pump…

A: Given data:

Q: Ammonia with MW=17, weighing 22kg is confirmed inside a cylinder equipped with a piston has initial…

Q: , Thrust washer A sluice gate weighing 18 kN is raised and lowered by means of square threaded…

Q: Find the forces in members EF, KL, and GL for the Fink truss shown. Forces are positive if in…

Q: 5. Dry winter atmospheric air at latm, 8°C and 50% humidity enter an HVAC system at a rate of…

A: human comforts refers to the physical comforts of the human being which can be adjusted by adjusting…

Q: 1. A piston-cylinder device contains 10.0 lb,m of water initially at 225 psia and 25.59 ft. Now 4000…

Q: An aircraft has a total mass of (1.26x10^2) kg and a wing area of (3.000x10^1) m2. It operated with…

A: Given Data: The density of air, 1.2 kg/m3 The total mass, m=1.26x102 kg

Q: If A = Gax + 3a, and B = 8'ax + 2ay-8 az, %3D (a) find the dot product (b) find OAR

A: GivenA→=6i^+0j^+3k^andB→=8i^+2j^-8k^

Concept explainers

Properties of Fluids

The term fluid represents a type of substance that can easily change its shape under any external pressure/force and can flow. Fluids can acquire any shape in which it is stored and can resist normal stresses but cannot resist shear stress in rest condition. Whenever external shear stress is applied to fluids, it starts to flow. The fluids may be liquid or gas. Example- water, air, etc.

Question

Compute the normal acceleration when the boy reaches the bottom of the profile. (m/s^2)

Weight of the man 67.50kg
Velocity Equation = V = 20(6.33 - y): where y is the height measured from the x-axis
%3D
%3D
Y.
y=0.055x+4.35
6.33m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Cylinder has a non-uniform density. Find y of the cylinder ( when density is ply) = 5.254 - 2,31 [kg/m²³], radius 3.75 m t theight is 78.17m. 117 2 => My
A cylindrical gate with surface XY is supported by a hinge at point 1. The length of the gate perpendicular to the figure is m. Solve for the magnitude of the horizontal component in kN. Unit wt of water = 9.81 kN/cu.m. LENGTH = 9 RADIUS = 6 ANGLE = 55 RADIUS X ANGLE 1 1,201.34 925.39 1.358.45 1.066.38
The rectangular lamina with breadth = 40 mm, depth = 60 mm. The Ixx value is mm4 Select one: O 10.66 x 104 O 24 x 104 O 72 x 104 O 32 x 104 Friction force always acts in a direction to the direction of motion. Select one: O inear O normal O opposite O perpendicular
A cylindrical gate with surface XY is supported by a hinge at point 1. The length of the gate perpendicular to the figure ism. Solve for the magnitude of the horizontal component in kN. Unit wt of water = 9.81 kN/cu.m. LENGTH = 6 RADIUS 8 ANGLE=53 RADIUS X ANGLE 1 O 1,062.35 O 1,201.34 O2,003.99 O 2,436.65
1- A 60 cm square gate has its top edge 12 m below the water surface. It is on a 45 angle and its bottom edge is hinged as shown in Fig. What force P is needed to just open the gate and its Water location? Hinge 45° 2- A tank containing water is shown in Fig. E Calculate the total resultant force acting on side ABCD of the container and the 6 ft location of the center of pressure. Y = 62.4 Ib/ft3 Water 8 ft B -20 ft
For the area below, evaluate 1. The (x,y) coordinates of the centroid (please mark your origin or reference point on the diagram) 2. The 2nd moments and product of area in centroidal-based xy (horizontal-vertical) coordinates 3. The principal 2nd moments of area, and the direction of the first principal axis relative to the horizontal (x) axis (anticlockwise positive) 50 75 30 150 60 50 15 Figure 1: Cross section (all dimensions in mm) Quantity Xc (please mark your origin on the diagram) Yc (please mark your origin on the diagram) Ix ly Ixv I₁ I₂ a1 (please show the direction) Value 30 Units
4. Given: Curb shown below Find: (1) Surface area and (2) volume 100 mm 150 mm 4 m 30° 150 mm 150 mm
1- A 60 cm square gate has its top edge 12 m below the water surface. It is on a 45 angle and its bottom edge is hinged as shown Water in Fig. What force P is needed to just open the gate and its location? Hinge 45° 2- A tank containing water is shown in Fig. E Calculate the total resultant force acting on side ABCD of the container and the 6 ft location of the center of pressure. y = 62.4 Ib/ft3 Water -20 ft
The cross-section of an open tank is shown below at left. BC is a cylindrical surface with radius r = 6 ft, and the tank water depth is h = 10 ft. A free body diagram (FBD) for hydrostatic analysis is shown below at right. Use this information to solve problems 12 through 15 on a per unit width (into the page) basis. FBD: A B B OThe magnitude of the horizontal force Fy is nearest 1a) 490 lb/ft width of tank (b) 1610 Ib/ft width of tank (c) 3120 Ib/ft width of tank (d) 12.5 Ib/ft width of tank (e) None of the above are close to being correct ) The center of pressure Yp is ft below the water surfa The magnitude of the vertical hydrostatic force Fy is nearest (a) 1765 Ib/ft width of tank (b) 3744 Ib/ft width of tank (c) 1980 Ib/ft width of tank (d) 10.4 Ib/ft width of tank (e) 675 Ib/ft width of tank The location of Fy left of side AB is nearest ft OST or DISTREBUTE - THANK YOU
ester SY 2021 ements utton Solve for the hydrostatic force per meter length acting on the radial tainter as shown in the figure. Unit Weight is 9.81 kN/cu.m. R = 5 ANGLE = 40 RADIUS ANGLE 316.156 O 122.813 79.254 212.562
Q 2: Find Ixx and lyy of the Lamina shown in Fig. 1 80 30 50 110 30 120 Fig. 1
1- A 60 cm square gate has its top edge 12 m below the water surface. It is on a 45 angle and its bottom edge is hinged as shown in Fig. What force P is needed to just open the gate and its Water location? Hinge 2- A tank containing water is shown in Fig. Calculate the total resultant force acting on side ABCD of the container and the location of the center of pressure. y = 62.4 Ib/ft3 Water -20 ft 3- Find the total pressure and position of center of pressure FREE WATER SURFACE on a triangular plate of base 2 m and height 3 m which is immersed in water in such a way that the plane of the plate makes an angle of 60 with the free surface of the water. The base of the plate is parallel to water surface and at a depth of 2.5 m from water surface. 4- The 200 kg, 5 m wide rectangular gate shown in Figure 05m is hinged at B and leans against the floor at A making an Water angle of 45° with the horizontal. The gate is to be opened 3m from its lower edge by applying a normal force at its…