Compute the compressive strength of a WT 12x81 of A992 steel. The effective length with respect to the x-axis is 25 feet 7inches, the effective length with respect to the y axis is 20feet, and the effective length with respect to the z-axis is 20 feet WT12X81 A 23.9 t₁ 1.22 ly 221 d 12.5 K des 1.72 J 9.22 bf 13.0 y 2.70 Cw 43.8 tw 0.705 1x 293

Compute the compressive strength of a WT 12x81 of A992 steel. The effective length with respect to the x-axis is 25 feet 7inches, the effective length with respect to the y axis is 20feet, and the effective length with respect to the z-axis is 20 feet WT12X81 A 23.9 t₁ 1.22 ly 221 d 12.5 K des 1.72 J 9.22 bf 13.0 y 2.70 Cw 43.8 tw 0.705 1x 293

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter5: Beams

Section: Chapter Questions

Problem 5.8.1P: Compute the nominal shear strength of an M107.5 of A572 Grad 65 steel.

See similar textbooks

Similar questions

The given plate below with width of 200 mm andthickness of 16 mm is to be connected to two plates ofthe same width with half the thickness by 20 mmdiameter rivets as shown. The rivet hole is 2 mm greaterthan the rivet diameter. Allowable tensile stress on netarea is 0.6Fy. Allowable bearing stress is 1.35Fy. plate: fy = 241 mpa fu = 4141 mpa rivet: fv = 152 mpa a. Determine maximum load P without exceeding allowable tensile stress on plate b. Determine maximum load P without exceeding allowable shear stress on rivets c. Determine maximum load P without exceeding allowable bearing stress between plates and rivets
H.W A Solid Steel bar of dlameter 6omm and length 350 mm is Placed inside an aluminum cylinder öf Inside diameter Femm and out side d lameter Ilomm, a comPressive load of looo lais applied on the assembly, find the stresses in the bar and the cylinder ? take Est = 200GPa and EAl = F0GPan %3D Cover Plate 0.25mm d- do 35omm A lum. cylinder Steel bar
EQuiz No.3 584nkkz1 Cc7KLzOsdr9YUFgvcfFSqpsdlyljtewQ/formResponse Choose the correct answer What will be the value of load applied parallel to the diagonal of (100x100x100))mm cube since the splitting tensile strength=3 Mpa 57.8 KN O 46.7 KN O 47.1 KN O (28)=27.5 Mpa, then the fc(180)=-- for concrete produced using moist
1. For the Pratt bridge truss and the loading shown below, determine the average normal stress in member BE, knowing that the cross-sectional area of that member is 60 in². NN K 12-12--12--12--| 50 lips 50 kips 50. ips Figure 1 G xfone
8. H / The beam shown below has across seclion of channel Shape with width 360mm.and haghs h= loomm, the web thickness ist= 14mm.Deler- Mine ihe Max imum tensile aud Compressive stressin the beam due to unifom Load? 360Mm 3.6KN/M 14m tiom Please Sir 5T CASIC f-991ES PL DATURAL u CALC (-)
AW 12 x 65 column section shown in the figure is pinned at each end and has an additional support in the weak direction at a point 4.1 m from the top. Use X- 4.8 m K 1 for both directions. X+Y Properties of W 12 x 65 A 12323 mm2 - 134.11 mm ry 76.71 mm Fy- 248 MPa Determine the allowable compressive strength (kN).
Determine the force of the members for the space truss shown in the figure. Joints A and B are supported by ball-and-socket while Joint C is supported by short link along z-axis. Indicate whether member is tension (T) or compression (C). 2m y Sm Az By BX Bz PAR Ax CSXScanned with Ca canner a SISU KN 15m 1 2117
Q4\ Which of the following is a zero-force member? 3 8KN 4 G 4 エ子c D. 4 B AC BD IF ID
2- A 2m COPPER BAR SUBJECTEO TO A TENSILE IS SUSPENDED FROM A LOAD IBO KN SUPPORTED BY TWO IDENTICAL PIN THAT S pOSIS AS SHON OF THE LOWER AFPLIED TENSILE POSTS SUPPORT THE STEEL DETERMINE THE TOTAL DEFORMATION END OF THE LOAD HINT: NOTE THAT THE STEEL PIN WHERE THE COFPER BAR IS ATTACHED. COPPER BAR DUE TO STEEL POST L=0.5m A= 4500mm E- 200GPA COPFER BAR L- am A= 4800 Mn E- l20 GPa 180KN
Determine the nominal axial compressive strength, Pn for the following cases: a. L = 15 ft b. L = 20 ft Note: Pinned both end support W10× 33 r = 1.94 in E = 29000 ksi Fy = 50ksi A992 steel %3D Note: Ag = 9.71 in^2 a) Blank 1 b) Blank 2 Blank 1 Add your answer Blank 2 Add your answer
PERFORMED AS REQUIRED. SHOW YOUR COMPLETE SOLUTION. 4.3-1 Use AISC Equation E3-2 or E3-3 and determine the nominal axial compressive strength for the following cases: a. L = 10 ft b. L=30 ft L W10 x 100 A992 steel FIGURE P4.3-1
Use 2015 NSCP. A compression member shown below with Fy = 50 ksi 30′ W12 x 87 A992 steel 1. Which of the following most nearly gives the value of critical buckling stress in ksi? 2. Which of the following most nearly gives the nominal strength in kips? 3. Considering ASD. Which of the following most nearly gives the allowable strength in kips? 4. Considering LRFD. Which of the following most nearly gives the design strength in kips?