Answered: Compute all the necessary elements of…

Engineering

Civil Engineering

Compute all the necessary elements of the old curve and new relocated curve.

Traffic and Highway Engineering

5th Edition

ISBN:9781305156241

Author:Garber, Nicholas J.

Publisher:Garber, Nicholas J.

Chapter14: Highway Surveys And Location

Section: Chapter Questions

Problem 17P: The following table shows the stations and ordinates for a mass diagram. The free-haul distance is...

See similar textbooks

Related questions

Q: In which fluid will a pressure of 680 kPa fırst be achieved? Po = 90 kPa ethyl alcohol p = 773.3 kg/...

Q: 45 m taped distance A surveyor used 75-meter line AB to compute his pace factor. The following are ...

A: The given data ,At day 3, the following are his number of paces for Line CD 517.00, 518.00, 521.00, ...

Q: 6. Determine the absolute maximum live moment in the bridge due to the loading shown. 20 kN 40 kN 25...

Q: fully saturated soil sample has a volume of 28 cc. The sample was dried in oven and the weight of th...

A: This question is related to Soil Property from soil mechanics.

Q: Find Out Shear and moment equations at different sections for the beams shown in figures. Find out v...

A: We will draw bending moment and shear force diagram.

Q: Given: Loads as shown on the truss. 50 kN Find: The forces in members 40 kN -2 m- -2 m- -2 m- ED, EH...

Q: Is your experimental yield of alum greater than, less than or equal to the theoretical yield? List s...

A: it is provided The potential yield is 17.858g, with a 72.42 percent percent yield. Because theoretic...

Q: Piston A has a cross-section of 1,200 cm^2 while that of B is 800 cm^2. B is higher than A by 2 m. I...

Q: 3. Determine the maximum tensile and compressive bending stress in the beam if it is subjected to a ...

Q: A uniform bar 1 is connected to a tapered rod 2. Both are subjected to axial loads as shown . If P =...

A: Given information in question Load tapered section Length Elastic modulus To find out Elongation i...

Q: A soil at a constant moisture content shows the following when compacted: Degree of Saturation (%) 4...

A: To determine the moisture content of the soil. Given, Degree of Saturation (%) Dry Unit Weight ...

Q: 12m L00 mm 100 mm The segment AB of the steel torsion bar is a cylindrical tube of constant 2-mm wal...

Q: A (0,7,0) TAB TAD FA TAC B (0,0,-4)

A: A = 0i +7j +0k B = 0i+0j -4k C = 7i +0j + 0k D = -2i +0j +3k Uni vector AB=B-A=0i -7j -4k Modulus of...

Q: 4. (Problem 4.24 from the text book) A 60-N · m couple is applied to the steel bar shown. (a) Assumi...

Q: A long excavation with vertical sides and depth-to-width ratio of 0.5 is to be made in a deep deposi...

A: Vertical side and Depth to width ratio (B) = 0.5 Undrained shear strength (USS) = 20kPa Saturated bu...

Q: Two circular shafts are joined together between fixed supports to resist a torsional moment of 80 kN...

Q: ent, node and mesh. AE 1000 L AE 100 10

Q: A fully saturated soil sample has a volume of 28 cc. The sample was dried in oven and the weight of ...

Q: C, VFc in kN LA in kN-m er KH, MKH in kN-m

A: force in columns

Q: Jsing a conservative estimate of snow fence yield of 2,000 gallons per linear feet, how much snow fe...

A: Detailed explanation is given below : We have to find the snow fence required for the city?

Q: Sand cone equipment is used to perform a field density on compacted earth fill. Sand is used in the ...

Q: Sieve analysis on a dry sample of mass 1000g showed that 980 g and 270 g of soil pass through the 4....

Q: A steel wide-flange section that is 18 in deep is used as a simple beam. If the moment of inertia of...

Q: Calculate for the following member forces of the frame shown below using Portal Method. a. Shear at...

Q: A soil sample has a unit weight of 1.9 g/cc and w=12%. If Gs of solids is 2.65, determine the void r...

A: This question is related to Soil Property from soil mechanics. In this question we calculate the voi...

Q: Can you Write a note on Balking, Reneging & Jockeying in Queuing System?

A: Brief concept- Queuing System- A line system is a system with a service area where different types o...

Q: 0.1 m 0.3 m O.lm N- アニ0.14m 0.1 m レ -0.2 m-

Q: s Pond has a surface area of 3.25 km2, and for a given month th of 3,400 L/s and an outflow of 2,750...

Q: Please help, I will give a good feedback. Short and simple answers are accepted as long as it is not...

Q: Specifications for a proposed earth fill require that a soil be compacted to 95% of Standard Proctor...

Q: find the shear forces and maximum bending moment

Q: Two circular shafts are joined together between fixed supports to resist a torsional moment of 80 kN...

Q: The beam is subjected to a moment of M = 40 kN.m. Determine the bending stress at points A and B. Sk...

Q: Given an axial failure stress of 2000 psi, a factor of safety of 1.67 and modulus of elasticity 1800...

Q: EXAMPLE 3.1 Given: Sieve analysis and plasticity data for the following three soils. Soil I. % Finer...

A: Given:- The sieve analysis and plasticity data of the three soils are given Sieve size Soil 1 So...

Q: Liquids A, B and C, in the containers shown, have SG of 0.60, 1.00 and 1.60 respectively. At what el...

Q: Design a three barrel siphon for carrying sewage across a river stream. The total length of the siph...

Q: A scow 50 ft long, 30 ft wide and 15 ft high has a draft of 9 ft. the center of gravity is at the ce...

Q: The following data are given for soil: porosity = 0.45, specific gravity of soil solids= 2.68, and m...

Q: If roller support is added at point C, 20ft. from point A. Determine the following: (Use Conjugate B...

Q: A rectangular box is floated. Outer dimensions 2m by 10m and has 2m high sides and weighs 4.9N. It ...

Q: At t = Os, an experimental electric powered car starts from rest at point A and moves toward the rig...

Q: O A long excavation with vertical sides and depth-to-width ratio of 0.5 is to be made in a deep depo...

Q: The initial void ratio of an inorganic clay is found to be 0.65, while the specific gravity of solid...

A: This question is related to the Soil Property from soil mechanics. In this question we calculate wat...

Q: A uniform bar 1 is connected to a tapered rod 2. Both are subjected to axial loads as shown. If P = ...

Q: A 10 m simply supported beam with 25 kN load 3 m from the left end has a maximum slope at the left e...

A: Given Data: The length of a beam is L= 10 m. The load on a simply supported beam is P = 25 kN. The d...

Q: A square footing 4m on a side 1.2m below the ground surface for which the bulk unit weight of the so...

Q: sm steel helln circular DoI00 mm Di 80 mm duminum Solid circular D= 75 mnv G- D GPo G- 1S0 6Pa

Q: Curve wall ABC is a quarter circle 9 ft into the paper. Compute the horizontal hydrostatic force on ...

A: To compute: horizontal component of the hydrostatic force on the wall vertical component of the hyd...

Q: Design a pile group consisting of R mm carrying a total load of 2000 kM consists of a deposit of cla...

A: Column size- 750mmx750mm P-2000kN Cc=0.1 eo =0.9 γ=21kN/m3 C=40 kN/m2 Fos=2.5 α=0.7 D=40mm

Concept explainers

Curve setting

A curve is a turn that is provided horizontally or vertically in the design of highways, railways, and runways. A curve connects two straight lines that are separated by the deflection angle. It helps to change the direction and alignment of the highways, railway tracks, and runways. Therefore, the gradual change in their alignment is made by using a curve to provide comfort to the passengers and this also provides an easy turn to change the direction of the moving vehicle.

Question

The angle between a 5-m full station of a certain curve is 10°. The curve has 7 intermediate stations between P.C. (10+300m) and P.T. After laying out the curve, it was found out that the P.T. falls in a property lot and it should be moved in a way that the P.T. will be free from crossing the lot. As an ENGINEER, what would be your advice for relocation? Compute all the necessary elements of the old curve and new relocated curve.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The angle between a 5-m full station of a certain curve is 10°. The curve has 7 intermediate stations between P.C. (10+300m) and P.T. After laying out the curve, it was found out that the P.T. falls in a property lot and it should be moved in a way that the P.T. will be free from crossing the lot. As an ENGINEER, what would be your advice for relocation? Compute all the necessary elements of the old curve and new relocated curve. *check attached image for reference. ** please do not forget to include illustrations/sketches.
The angle between a 5-m full station of a certain curve is 10°. The curve has 7 intermediate stations between P.C. (10 + 300m) and P.T. After laying out the curve, it was found out that the P.T. falls in a property lot and it should be moved in a way that the P.T. will be free from crossing the lot. As an ENGINEER, what would be your advice for relocation? Compute all the necessary elements of the old curve and new relocated curve.Please do not reject this question and help me understand this complicated problem about curve relocation. It would be better if you will provide me with a detailed solution. Thank you!
A-1.10% grade meets a +0.60% grade at station 36+00 and elevation 800.00 ft. The +0.60 grade then joins a +2.40 grade at station 39+00. Part A Determine the elevation at the low point of the curve. Express your answer in feet to six significant figures. Elev = Submit Part B VAΣo↓ vec Request Answer Determine the station at the low point of the curve. Submit O 38+42.763 O 35+40.763 O 36+42.763 O 36+44.763 Request Answer ? ft
You are going to design a circular curve in a rural road segment where the design vehicleis a passenger car of operation speed is 90 km/h. The width of the lanes of the proposedroad is 3.5m. Based on a survey at the proposed site, it has been found that a multi-storiedbuilding is located towards the inside of the curve at 10 m from the centerline of thehighway. Considering perception reaction time as 2.5 s design the horizontal curve (Rdesign,edesign and fdesign) for that road segment. Record the radius and respective safe sight distancein the tabular format while selecting design radius (word table), plot them in Excel graphand find the Rdesignfor the safe sight distance. If there is no superelevation, what would bethe alternative arrangement?
Copy the questions and answer. Provide necessary drawings / illustrations base on the problems. Problem 1: A -3% grade meets a +5% grade near an underpass. In order to maintain the minimum clearance allowed under the bridge and at the same time introduce a vertical transition curve in the grade line, it is necessary to use a curve that lies 200m on one side of the vertex of the straight grade and 100m on the other. The station of the beginning of the curve (200m side) is 10+ 000 and its elevation is 228m. a.) Determine the elevation at station 10 + 040. b.) If the uphill edge of the underside of the bridge is at station 10+ 220 and at elevation 229.60m, what is the vertical clearance under the bridge at this point? c.) Determine the stationing of the lowest point of the curve. P..C. 10+000 Fl. 228 m 40 -200 81=-38 10+040 H -100 20+5% 8=(500+£0 3001 -
Read the question carefully and give me right solution according to the question. Station 10+00.00 has an elevation of 110.00 and a grade of -3%. Station 20+00.00 has an elevation of 105.00 and a grade of +2%. What is the stationing at the two grade intersections? options A) 14+00, B) 15+00, C) 16+00, D) 17+00)
A 500-ft curve, grades of g₁ = +2.00% and g2 = -2.50%, VPI at station 96+80, and elevation 845.260 ft, stakeout at full stations. Part A Determine the elevation at the high point of the curve. Express your answer in feet to six significant figures. Elev = Submit Part B AΣo↓ vec Request Answer Determine the station at the high point of the curve. O 97+12.77 O 96+13.33 O 96+52.22 O 97+96.66 ? ft
The data given for a vertical sagcurve on a roadway plan andprofile sheet are as follows: PVIstation @ 32+11.61, PVI elevation =54.18 ft, back tangent gradient g1 =- 4.00 percent, forward tangentgradient g2 = + 7.00 percent, andlength of curve L= 600ft. Determinethe curve elevations at half-station intervals along the curve,and compute the station andelevation of the lowest point. PLEASE PROVIDE COMPLETE AND COMPREHENSIVE SOLUTION AND FINAL ANSWER ASAP
The angle between a 5-m full station of a certain curve is 10°. The curve has 7 intermediate stations between P.C. (10 + 300m) and P.T. After laying out the curve, it was found out that the P.T. falls in a property lot and it should be moved in a way that the P.T. will be free from crossing the lot. Compute all the necessary elements of the old curve and new relocated curve. PLEASE DRAW SKETCHES OF THE CURVE. USE METERS AS UNIT.
A four-lane undivided highway (two lanes per direction) has a segment of horizontal curve with the radius of 440 ft measured to the center line of the highway.The lane width is 12 ft. The inner lane of the curve has a 6 ft wide shoulder. A sound wall has been constructed at 12 feet from the edge of the shoulder calculate the available site distance (S) if the SSD is 246 ft. Is the site distance adequate ? Please show steps I dont just want the answer. Thank you in advance
INSTRUCTION: COMPLETE SOLUTION WITH FIGURES. BOX YOUR FINAL ANSWER. An underpass crossing a reinforced concrete bridge along the Shaw Blvd has a symmetrical vertical curve, having a downward grade of -4% meeting an upward grade of +7.5% at the vertex V at elevation 70 m and stationing of 7+700, exactly underneath the center line of the bridge having a width of 10 m. If the required minimum clearance under the bridge is 5 m, and the elevation of the bottom of the bridge is 78.10 m. a) Determine the length of the vertical parabolic curve that shall connect the two tangents. b) Determine the stationing of the point a catch basin (lowest point) will be placed. c) Determine the elevation of the point where a catch basin (lowest point) will be placed.
1. What are the extra clearances provided on a curved track? Describe the extra clearances provided between two adjacent curved tracks. 2. Establish a relationship between the radius and versine of a curve. How is the degree of a curve determined in the field? 3. Enumerate the various methods of setting out a circular curve. Describe the tangential offset method for laying a circular curve. 4. Which among the future railroads development are you most looking forward?