Compare materials quantity for M30 grade of concrete? Table:2. Materials quantity for M30 grade of concreteIngredientsBISACIDOEWater/cementRatio0.450.470.5Water197212236content(kg/m³).Cement438.2425.5450content(kg/m³)Weight of coarseaggregate(kg/m³)113010441034Weight of Fineaggregate(kg/m³)651672630

Answered: Compare materials quantity for M30…

Engineering

Civil Engineering

Compare materials quantity for M30 grade of concrete?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q5/ Find job mix formula by using mathematical method. Aggregate Specification Sieve Size A B Limits 25 mm 100 100 100 100 12.5 mm 100 100 97 90-100 4.75 mm 100 100 55 60-90 1.18 mm 98 79 38 28-58 0.3 mm 98 39 28 6-38 0.15 mm 11 16.5 7 10-23 0.075 mm 4.1 8 2.15 4-10
A sieve analysis test was performed on a sample of fine aggregate and produced the following results:Sieve, mm 4.75 2.36 2.00 1.18 0.60 0.30 0.15 0.075 panAmount retained, g 0 33.2 56.9 83.1 151.4 40.4 72.0 58.3 15.6Calculate the percent passing each sieve, and draw a 0.45 power gradation chart with the use of a spreadsheet program. The specific steps or functions selected in the following description can vary somewhat depending on the version of the spreadsheet program being used.
What is the w/cm for the following 1 m3 batch of concrete? Express your answer with 2 decimal places. Material Batch mass, kg Cement 250 Pozzolan 84 Fine aggregate (absorption 0.8%. moisture content, 4%) Coarse aggregate (absorption 0.4%. moisture content 1.5%) Water added to the batch mix 623 1177 116
Discussion: 1- What is the difference between apparent specific weight and total specific weight? 2- If an error occurred and the model dried more than the case of S.S.D saturated and the surface is dry), what is the effect of this on the total specific weight and the apparent specific weight. 3- What are the difficulties that arise when using aggregates containing free water or dry aggregates in concrete mixtures? How to overcome this: A - in the laboratory? b- On the job site?
A sieve analysis was conducted on a graded aggregate with a nominal maximum aggregate size of 20 mm. Th following data was obtained: Sieve size (mm) Mass retained (g) 37.5 0 26.5 19.0 9.5 4.75 2.36 Pan 80 120 800 1450 130 80 a) Find the mass passing and percentage passing on each sieve and fill in the table provided in the answer sheet. b) Fill in the upper and lower limits of the Australian Standard (AS2758) for this aggregate type. c) As per the AS2758, is the aggregate well-graded? Explain your answer. d) What should be done if the aggregate is poorly graded?
4 pts Question 23 What is the fineness modulus of this aggregate? % Cumulative Retained Retained Mass 0% Sieve Size (US) (g) Retained Passing 1" 3/4" 1/2" 3/8" # 4 650 18.3 700 19.7 632 17.8 175 4.9 # 8 200 5.6 #16 W 150 4.2 #30 125 3.5 #50 331 9.3 #100 288 8.1 #200 250 7 Pan 50 1.4 Total 3551 O 5.20 O 1.57 O 3.89 O 6.50
A sieve analysis test was performed on a sample of aggregate and produced the results shown in Table P5.21. TABLE P5.21 Amount Sieve Size, Amount Sieve Size, mm Retained, g mm Retained, g 25 1.18 891.5 19 376.7 0.60 712.6 12.5 888.4 0.30 625.2 9.5 506.2 0.15 581.5 4.75 1038.4 0.075 242.9 2.36 900.1 Pan 44.9 Calculate the percent passing through each sieve. Plot the percent passing versus sieve size on: a. a semilog gradation chart, and b. a 0.45 gradation chart (Figure A.25). What is the maximum size? What is the nominal maximum size?
SITUATION. The basic data for proportioning trial batches for normal weight concrete with an average with an compressive strength of 35 MPa at 28 days are as follows: Slump = 75 mm to 100 mm Water-cement ratio by weight = 0.48 Specific gravity of cement = 3.15 Specific gravity of coarse aggregate = 2.68 Specific gravity of fine aggregate = 2.64 Water (net mixing) = 180 kg/m^3 Concrete unit weight = 23.6 kN/m^3
5.24 Three aggregates are to be mixed together in the following ratio: Aggregate A 35% Aggregate B 40% Aggregate C 25% For each aggregate, the percent passing a set of five sieves is shown in the fol- lowing table: Sieve Size (mm) % Passing Agg. A % Passing Agg. B % Passing Agg. C 9.5 85 50 40 4.75 70 35 30 0.6 35 20 0.3 25 13 1 0.15 17 7 Determine the percent passing each sieve for the blended aggregate.
A cement grinding mill "A" with a capacity of 50 tons per hour employs P12,000 per tonforged steel grinding balls with a wear rate of 100 grams per ton of cement processed.Another cement mill of the same capacity, "B," utilizes P50,000 per ton high chromesteel grinding balls with a wear rate of 20 grams per ton of cement processed.Determine the more cost-effective grinding mill, keeping all other factors constant. do not use excel, use formula
epare a datasheet and calculate the cost of plastering cement (1:5), 20mm thick for 50m². Also compute final total cost 0.5 skilled labor $70/day T3 unskilled labor $20/day Mixing charge of cement mortar $7/m³ 7 Lead in KM S.# Rate at Material Metal Cart Conveyance Charge Sand track source, Toll Charge track track 1 $110 1.2 0.8 $5/KM/2ton 1 $30 1.0 0.9 0.5 $3/KM/m³ $5 0.6 0.7 $1/KM/m² $2/25m² WID 2 3 Cement Sand Paint per Ton m³ m²
8. What is the maximum allowable limit of Materials Finer Than 75 Mm (No. 200) Sieve in Coarse Aggregates in % according ASTM C33? 9. What is the maximum allowable limit (in %) of clay lumps and friable particles in fine and coarse aggregates? 10. What is the maximum allowable limit of loss (in %) of a coarse aggregate sample tested for abrasion and impact in the Los Angeles Abrasion Machine?