Draw the influence lines for the following using the coordinates (basic method) or using the Muller-Breslau principle, show the value of the ordinates. 1. Vertical reaction at A 2. Vertical reaction at B 3. Shear at C 4. Moment at C 5. If there is a moving 10KN concentrated load along the beam, what would be the maximum value of the vertical reaction at A? 6. If there is a moving 10KN concentrated load along the beam, what would be the maximum value of the shear at C? 7. If there are moving loads, 10KN concentrated load and 2KN/m uniformly distributed live load, what would be the maximum value of moment at C? IL(1).png B C -2 m 6 m

Draw the influence lines for the following using the coordinates (basic method) or using the Muller-Breslau principle, show the value of the ordinates. 1. Vertical reaction at A 2. Vertical reaction at B 3. Shear at C 4. Moment at C 5. If there is a moving 10KN concentrated load along the beam, what would be the maximum value of the vertical reaction at A? 6. If there is a moving 10KN concentrated load along the beam, what would be the maximum value of the shear at C? 7. If there are moving loads, 10KN concentrated load and 2KN/m uniformly distributed live load, what would be the maximum value of moment at C? IL(1).png B C -2 m 6 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

a. The beam shown is supported with a hinge support at A and a roller support at B. Determine the support reactions if the beam is in equilibrium. The triangular load varies from 0 to 1kN/m. and there is a clockwise couple of 10kN-m at B. The 2kN concentrated load at the right end is directed up. 3m -Im 2KN
In influence line for vertical reactions at support A and the moment at point B of the beams are shown. From the influence line of support A, what is the value of Ay when x = 4.20 m due to a unit load?
If the shear at point A on a beam is zero, then A.the slope of the bending moment at A must be zero B.the load intensity at A must be zero C.the magnitude of the bending moment at A must be at its maximum D.the slope of the load at A must be zero For the simply supported beam loaded as shown, which of the following is FALSE? A.The slope of the bending moment diagram at A is zero. w1 w2 B.The bending moment at A is zero. C.The bending moment diagram is a cubic curve. D. The bending moment is positive throughout the beam. Which of the following is FALSE? A. The slope of the shear diagram at A is negative. B.The shear at A is higher in magnitude than that at B. C.The slope of the shear diagram is constant throughout the beam. D.The shear diagram is concave upwards. For the simply supported beam loaded as shown, which of the following corresponds to the internal bending moment equation in section BC assuming x is the distance from point A? L L A. Ma-Mo 2 2 B. z+Mo C. Mo B D. Me T-Mo C Mo
%3D If the intensity of the distributed load acting on the beam is w = 3KN/m, determine the reactions at the roller A and pin B. 3 TA
Refer to the beam shown below a. Draw the influence line for the vertical reaction at internal hinge C. b. Determine the maximum moment at D and its location when a 12kN load travels across the beam.c. Determine the length and position of a 10kN/m uniformly distributed load that will give a maximum positive shear at C. d. What is the moment at point D when the previous scenario (letter c) happens? provide solution asap, answers in 4 decimal places
For the beam shown in figure below, compute for the following ordinates of the influence lines. a = 2.3 m. b = 2.5 m, C = 2.3 m Solve the following with complete solution. - Ordinate of the influence line of Rc at point D. - Ordinate of the influence line of Re at point B. - Ordinate of the influence line of Md at point F.
There is a joint at the C point in the AB beam, one end of which is fixed and the other end is held with a sliding support. Of beamits cross section is given below. To the beam, as shown in the figure between CB and 100 kN from point BAn axial load of magnitude (35 P) is acting.a) Draw the bending moment diagram (influence line) and find the absolute maximum bending moment value.b) Where the absolute maximum moment found in (a) occurs, at the point P shown in the cross sectionDetermine the state of the stresses.c) Find the principal stresses and axes for the stress condition you calculated at point P.
Use the Müller-Breslau principle to sketch the influence lines for the vertical reaction at A, the shear just to the left of the roller support at E, and the moment at A. A D E
the beam in the figure below is to be loaded with 20kN single axle load, a uniformly distributed live load of 25 kN/m, and a uniformly distributed dead load of 10kN/m. Considering the loads, A. determine the highest negative ordinate of the influence line for the moment at B B. For the beam shown below. determine the highest negative coordinate of the influence line for the shear B C. determine the maximum positive shear at B
For the beam shown in figure 1 below, compute for the following ordinates of the influence lines. a = 2.3 m. b = 2.5 m, C = 2.3 m Solve the following with complete solution. - Ordinate of the influence line of Re at point D. - Ordinate of the influence line of Re at point B. - Ordinate of the influence line of Mp at point F.
A beam is loaded and supported as shown. Assume w - 12 kN/m and L- 12 m. (a) Use the double-integration method to determine the reactions at supports A and B. Reaction forces are positive upwards and couples are positive counter-clockwise unless otherwise stated. (b) Draw the shear-force and bending-moment diagrams for the beam. L Part 1 Cut a cross-section through the beam and draw a free body diagram to the left of the cut. Determine the internal bending moment in terms of A,. Check your equation by solving for M(x) atx- 6 m. M(x) Answer: Mx-6m kN-m + mAy
Influence Lines. , (a) For the determinate beam shown below, draw the Qualitative influence lines for: Moment at D, Reaction at E, Shear at D, and Reaction at C. „Internal hinge В E Mp B E Ey В Vp Cy C D. E