Circle all correct statements for the Young's or elastic modulus, E:a. Has units of force per unit area.b. Is a measure of the ductility of a metal.c. Can be used to determine transverse strains in uniaxial loading.d. Is a material property.e. Is the slope of the elastic portion of a stress-strain (s-e) tensile curveCircle all of the statements that describe interstitial solid solutions:a. Is an example of a line defect.b. A solute atom replaces a solvent atom in the matrix.c. Would predict formation when adding carbon (C) to iron (Fe).d. Would predict formation when adding chromium (Cr) to iron (Fe).e. Requires the formation of a cation-anion vacancy pair.f. The solute atom has a smaller radius than the solvent atom.

As per our guidelines, we are supposed to answer only first one question in case of multiple…

Circle all correct statements for the Young's or elastic modulus, E: a. Has units of force per unit area. b. Is a measure of the ductility of a metal. c. Can be used to determine transverse strains in uniaxial loading. d. Is a material property. e. Is the slope of the elastic portion of a stress-strain (s-e) tensile curve

Circle all correct statements for the Young's or elastic modulus, E: a. Has units of force per unit area. b. Is a measure of the ductility of a metal. c. Can be used to determine transverse strains in uniaxial loading. d. Is a material property. e. Is the slope of the elastic portion of a stress-strain (s-e) tensile curve

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

STRENGTH OF MATERIALS. Please show the complete solutions. NO LONG EXPLANATION NEEDED! Rate will be given. Answer ASAP! Please answer all. MULTIPLE CHOICE: CHOOSE THE CORRECT ANSWER 1. Using MOHR CIRCLE from the given stresses on two perpendicular planes what is the normal stress on plane a-a? a. 75 MPa b. 150 MPa c. 125 MPa d. 100 MPa 2. Using MOHR CIRCLE, what is the resulting "HORIZONTAL" SHEARING STRESS at the given angle plane point? a. 44.03 MPa b. 64.32 MPa c. 185.68 MPa d. 75.00 MPa 3. Using MOHR CIRCLE, what is the resulting "VERTICAL" NORMAL STRESS at the given angle plane point? a. 44.03 MPa b. 75.00 MPa c. 64.32 MPa d. 185.68 MPa
Under which of the conditions below is the generalized Hooke’s law applicable for use in analysis? a. When the material distorts due to any of the normal stresses b. When the material has a negative value for Poisson’s ratio c. When the material exceeds its proportional limit but still remains elastic d. When the material’s cross-section changes along one direction Which of the following statements is false about the Poisson’s ratio? a. It is a dimensionless quantity b. It relates the modulus of elasticity E and the modulus of rigidity G c. It has a single value for isotropic and homogeneous materials d. Its magnitude is equal to the negative ratio of the longitudinal strain to the lateral strain.
Fast please please Basic differential between stress and strain formula.
Question 8. The following figure represents three hardness-testing techniques of materials. Describe their specifications, how there are conducted and their potential applications? 8 - Shape of Indentation Test Indenter Side View Top View Load Brinell 10-mm sphere P of steel or tungsten carbide Vickers Diamond 136° microhardness ругamid Rockwell and 60 kg) 100 kg } Rockwell 150 kg) Diamond 120° superficial cone: s - in.- diameter Rockwell 15 kg 30 kg } Superficial Rockwell 45 kg) steel spheres
Select all answers that are correct. Which of the following statements explain why solids have shapes and fluids do not? O A fluid develops a finite deformation when subjected to a shear stress a A fluid deforms continuously when subjected to a shear stress A solid develops a finite deformation when subjected to a shear stress O A solid deforms continuously when subjected to a shear stress
As Fast As you can Please mak sure the answer is correct 100% Please match the following to the appropriate areas or sublocations illustrated on the steel stress-strain curve shown below: (ultimate tensile stress- yield stress - repture stress) (4) The maximum stress point on the stress strain curve. (2) The point where the proportional limit ends and the moment the elastic limit of the specimen is reached, the specimen will return to its original state after the loading is removed. Typically occurs before the steel specimen starts to plastically yield. (5) The point at which the steel specimens has underwent necking and breaks. This typically occurs after the maximum stress is reached during the experiment.
10. Measure the diameter of impression using the profile projector and compute for the hardness number using the formula: Where: 2P P – Applied Load D - Diameter of steel ball (8.0 mm) BHN «D(D- /D² – d² d - Ave. diameter of indentation | Raw data: Diameter Specimen (carbon steel) d1 d2 Air cooled 5.13 5.22 Oil quenched Water quenched 4.12 4.36 3.74 3.81 Note: All dimensions are in mm.
Given the following stress-strain graph:a. is the modulus of elasticity of "A-514" greater, less or equal to the one of "A-572"?b. from the previous question, make an estimatio for both of them, check that the graphic comes in %c. If we were to test these materials in a universal tension equipment, which one would withstand more load?d. If we were to test these materials in a universal tension machine, which one would elongate the most before fracturing? would elongate the most before fracturing? e. Of the 6 materials shown, do any behave as brittle materials? f.
Fill in the blanks: A tensile test is carried out to determine the strength constant C and strain-rate sensitivity exponent m for a certain metal at 1000°F. If temperature were decreased to 900°F, the strength constant C would . .and the strain- rate sensitivity exponent m would. . Select one: a. C would stay constant, m would Decrease b. Nothing would change c. C would Increase, m would Decrease d. C would Increase, m would stay constant e. C would Decrease, m would Increase
q1: Describe tensile test in detail considering the steps. . define stress , strain (equation and units) . elasticity modulus, elastic and plastic zones . toughness, resilience of matiral Demonstrate stress strain curve for your answer
In the following problem please include a sketch of the problem, quantities given, quantities to be found, and boxed answer with units.
a . Sketch stress strain curve if the result shown in table represent the force and extension happened in steel, and show Mechanical properties that we get from tensile test on curve? (10p)Note : Lo=80 mm , Do=10 mm , use excel to plot the curve ExtensionLoad(mm) (N)0 0.900.83 4694.341.67 4831.412.50 4781.083.33 4918.834.17 4926.585.00 5257.075.83 5437.016.66 5575.888.33 5775.189.16 5847.5210.83 5965.4111.67 6010.5312.50 6042.5713.33 6072.2614.16 6092.9315.00 6113.2416.67 6140.3617.50 6146.3718.33 6148.1419.16 6149.1725.00 5940.2125.83 5675.3326.67 4725.52b. What is meant by modulus of rigidity? if it increases what does happen to material? (2p)