Calculate the steel of spiral stirrups for a circular pile of X meter height where X is 133 and diameter of 1.25 meter, take overlap as 40D for every 25 meter length of spiral, pitch as 12 cm, diameter of spiral bar as 12 mm and concrete cover as 8 cm.

Calculate the steel of spiral stirrups for a circular pile of X meter height where X is 133 and diameter of 1.25 meter, take overlap as 40D for every 25 meter length of spiral, pitch as 12 cm, diameter of spiral bar as 12 mm and concrete cover as 8 cm.

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter9: Pile Foundations

Section: Chapter Questions

Problem 9.2P: Refer to the pile shown in Figure P9.1. Estimate the side resistance Qs by Using Eqs. (9.40) through...

See similar textbooks

Related questions

Q: Q3. A 1200-lb hammer falling freely through 3 ft drives a 600lb pile in. vertically into the ground.…

Q: 2. Determine the allowable load carrying capacity of the pile shown below. The average unit skin…

A: Given that, average unit skin resistance = 1.2kN/m2 unit point resistance = 30kN/m2 FS=3.0 length…

Q: Q4) The ultimate load capacity of a 10 m long concrete pile of square cross section 500 mm x 500 mm…

Q: A single pile of diameter 50 cm and length 10 m is driven into clay having unconfined compressive…

Q: A 500 mm wide, square section pile, 12 m long is driven in a deep deposit of uniform clay. Value of…

Q: Calculate the load bearing capacity of the pile shown in Figure Q5. Assume that it is a bored pile,…

A: Given, L = 18.5 m B = 0.60 m

Q: A 1200 lb hammer falling freely through 3 ft. drives a 600 lb pile 6 in. vertically into the ground.…

A: Given data in question Weight of pile = 600 lb Weight of hammer = 1200 lb Settlement of pile = 6…

Q: A pile with a square cross-section, B × B = 0.5 m × 0.5 m, is driven in a clay soil which has an…

Q: For a group of piles 3x5 with pile diameter is 0.4m and centre to centre spacing is 2.8 m,if the…

A: in given question , there is 3*5 pile with 0.4 m dia and 2.8 m spacing width of pile group=…

Q: Check the total settlement of a group of pile as shown in Figure 1. The to set not exceed 3% of the…

Q: Define the method of obtaining ultimate load and also allowableload on a single pile from pile load…

A: pile load test is the in situ method of the calculation of the load and settlement. this method is…

Q: 3. As shown in the diagram, the RC solid precast square pile will be lifted up by two points, the…

Q: 2. Consider a pipe pile having an outside diameter of 500mm. The embedded length of the pile in…

A: Given, Pile diameter (D) = 500 mm or 0.5 m Embedded length (L) = 22 m

Q: A timber pile 400 mm in diameter is subjected to the following axial compressive loads: dead =600…

A: Solution Given Data Diameter= 400 mm Dead load= 600 kN Live load= 250 kN earthquake=200 kN Allowable…

Q: A 30-m-long concrete pile is 305 mm x 305 mm in cross section and is fully embedded in a sand…

A: Solution; Find the moment of inertia of the pile using relation; Ip=B412 Here the moment of inertia…

Q: 05. Estimate the pile length required to sustain an uplift force for the pile (30 x 30 cm) shown in…

Q: Q4: It is required to construct a pile foundation comprised of 25 piles arranged in 5 columns at…

A: Formula for settlement = ((H × Cc)/(1+e))×log((sigma+delta…

Q: A precast circular pile (like a concrete rod) of length Land diameter D is to be lifted at two…

Q: An 18" square solid concrete pile is driven with an impact hammer to a depth of 55ft below grade…

A: Solution: Considering the Diagram: Qp=qpApqp=σvo' Nq*≤0.5pa Nq*tanφ…

Q: SITUATION. A 15m precast concrete pile is to be lifted. If the unit weight of concrete is 23.54kN/m3…

A: let w be the udl over pile w = 23.5x0.4x0.4 = 3.76KN/m

Q: The average values of the undrained shear strength (c,) with depth are given as follows: Depth (m) ,…

A: The length of the pile lies between the 8 m to 12 m. So, cu=80 kN/m2 The empirical adhesion factor…

Q: Q4: It is required to construct a pile foundation comprised of 25 piles arranged in 5 columns at…

A: Given Data: imposed load= 3000 kN diameter = 50cm length= 12m The water table depth = 6 m n= 25…

Q: Determine the maximum load that can be allowed on a 45cm x 45cm diameter bored pile shown in…

A: Calculate the ultimate load carrying capacity of the bored pile, Qu = 133NAb + 0.67N'As N - SPT N…

Q: Discuss the method of obtaining ultimate load and also allowableload on a single pile from pile load…

A: Pile load test is the in situ method of the calculation of the load and settlement. This method is…

Q: A concrete bored pile has a diameter of 800 mm as given in the figure below. Calculate the ultimate…

A: Solution Given Data Diameter= 800 mm=0.8 m

Q: The horizontal floor with a length of 15 m, has one downstream sheet pile with a depth is 12 m, an…

A: H=3 m Take ρ of concrete=2.45α=bd=1512=1.25λ=1+1+α22=1+1+1.2522=1.3 Required: To calculate floor…

Q: A 30 cm diameter concrete pile is driven into a homogeneous consolidated clay deposit (C = 40 kPa, a…

Q: QUESTION 3: Three forces act on a pile as shown. If the resultant of the three forces is equal to…

A: An arrangement of forces have been given and it has been asked to determine missing force and its…

Q: A group pile has a section of 4 x 4 with each having a diameter of 305 mm are embedded in clay. The…

A: Given Data: Group pile=4*4 Diameter of pile=305 mm Length of the pile= 12 m Spacing between the…

Q: A 20 m long bored concrete pile having a diameter of 375 mm is load tested, and the data are given…

A: According to given data 20m long bored concrete pile pile dia 375 mm

Q: Q.1 Consider a real-life scenario in which you have to do a piling work on a dry surface? The Pile…

A: The following equipment are used during piling for the given condition: 1. Piling rigs: This is used…

Q: Answer the following questions – showing in order, complete and correct handwritten solutions. Use…

A: As there are multiple questions posted, according to the guidelines only the first is being…

Q: b) A bored pile was installed in dense sand with the following data- kN/m The ground water table was…

A: Diameter of pile (d) = 0.6 mLength of pile( L) = 20 mAngle of internal friction(ϕ) = 30°γ = 20…

Q: A timber pile of length 8 m and diameter

Q: 10. The hammer of a pile driver weighs 1000 lbs and must be lifted a vertical distance of 6ft in 3…

Q: SITUATION 1: A pre-stressed concrete pile of length L is to be picked up by crane at two points,…

A: Due to the loading in the pile no cracking will be form hence the positive bending moment at mid of…

Q: The Danish pile-driving formula is to be used for field control of a pile installation. Steel pipe…

A: Part a.

Q: 4. The following data was obtained in a vertical pile load test on 300 mm pile diameter pile.…

A: Safe load / Allowable load on a single pile should be the least of the following: 1 Two-thirds of…

Q: A 40 cm driven concrete pile driven through layered soil shown in figure below. Estimate the…

Q: Given the sheet pile shown in figure : 1. Draw the flow 1.5m i 3.0mi net to scale (1:100) and

A: According to given data , the structure is safe , as Factor of safety is greater than 1 , calculated…

Q: Q Y- 17.5 kN/m Cohesion = 28 kPa a - 0.95 Y= 17.8 kN/m w = 25% & Gs = 2.6 Cohesion = 35 kPa a = 0.85…

Q: A concrete pile is 15 m long and has 406 mm diameter circular cross section. The pile is fully…

A: It is required to find I. Ultimate point load resistance of pile Ii. Total Ultimate skin friction…

Q: Assume in problem 2 that the water table is at the ground surface and the saturated unit weight is…

A: Given Length of concrte pile L=15 m and diamete D=45 cm=0.45 mfriction angle ϕ=30°water…

Q: 8. Pile Capacity Calculations A 30" diameter friction pile which has a 24' length in contact with…

Q: Elevati Distanc on (ft) (y- axis) e (ft) (x- axis) 5 15 10 17 10 18 15 19 15 28 33 40 -5 44 -5 54…

A: First find the excavation volume using the give values and then determine the volume of filling.…

Q: Note: Read the question carefully and give me right solution according to the question. A pile is…

A: Foundations are provided in a structure to provide stability and transfer the load to the soil…

Q: Check the total settlement of a group of pile as shown in Figure 1. The total allowable settlement…

Q: The plan of a group pile is shown in the Figure below. Assume that the piles are embedded in a…

A: Procedure to find the allowable load-bearing capacity of pile group: Calculate the ratio of CuPa.…

Concept explainers

Pricing Excavation and Backfill

Backfill, in construction, is the activity of returning the soil and gravel that are removed during building construction or using them again to toughen and support the foundation of the building or any other structural component.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Given

VIEW

Step 1

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Refer to the pile shown in Figure P9.1. Estimate the side resistance Qs by Using Eqs. (9.40) through (9.42). Use K = 1.5 and Coyle and Castello’s method [Eq. (9.44)]
Q1- Determine the allowable bearing load of the pile shown in figure Q1 using all the possible methods of solution. Mention the method used, and draw clear labeled drawings to clarify your calculations.
Describe the Arrangement for Piles in a Group.
10. The hammer of a pile driver weighs 1000 lbs and must be lifted a vertical distance of 6ft in 3 sec. what horsepower engine is required?
A frictional pile with a circular cross- section (diameter = D) is pushed into the soil to a distance (L) and then it is %3D subjected to an axial force (P) on its top end. Derive a formula to calculate the normal stress in any section x. f N/mm2 D Cross section Maximum size for new files: 128MB Files
Note: Read the question carefully and give me right solution according to the question. A pile is made of recycled aggregate material. The pile has a diameter of 95 ft. at the base, and30 ft. at the top. It is 23 ft. high. The volume of the pile (yd3) is most nearly: a ) 1,350b ) 89,643c ) 2460d ) 3320
DESIGN A PILE CAP USING THE STRUT AND MODELING METHOD. A 16"x16" precast concrete pile with pile capacity of 122kips, fc' = 5000psi, length of pile is 55' and the column load is 159.8kips.
What is Group capacity of pile ?
5. An 18" square solid concrete pile is driven with an impact hammer to a depth of 55ft below grade into the soil conditions below. Calculate the (Qultimate) and (Qallowable) assuming a FOS of 2, assume groundwater is at the surface. Show all work use Alpha and Meyerhof methods. Oft NC Clay Ysat = 135 pcf c = Su = 900psf 55ft Sand Kat = 130 pcf Phi = 38deg 80ft 6. All things being equal for the above problem use the Coyle and Castello method and find (Qultimate) and (Qallowable)
Q # 1. What is pile foundation? Discuss the classification of pile based on materials/composition and load transfer mechanism.
a 15-meter precast concrete pile is to be lifted. if the unit weight of concrete is 23.54 kN/m3. And the section of the pile measures 400 mm by 400 mm.
A steel pile (H-section; HP 360 1.491; see Table 18.1) is driven into a layer of sandstone The length of the pile is 18.9 m. Following are the properties of the sandstone: Unconfined compression strength = qu(lab) = 78.7 MN/m2 Angle of friction = 36 Using a factor of safety of 3, estimate the allowable point load that can be carried by the pile. Use Eq. (18.42).