Calculate all the reactions of the three- dimensional frame and for the node in red the translation about the y-axis, and the rotation about the x-axis. Consider that all the beams are the same, square cross section of 10cm side, E=200GPa and v=0.3 USE THE UNITARY VIRTUAL CHARGING METHOD/ FLEXIBILITIES

Calculate all the reactions of the three- dimensional frame and for the node in red the translation about the y-axis, and the rotation about the x-axis. Consider that all the beams are the same, square cross section of 10cm side, E=200GPa and v=0.3 USE THE UNITARY VIRTUAL CHARGING METHOD/ FLEXIBILITIES

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

3) The rectangular tube cross-section of a beam, demonstrated in the figure aside, is bent about a horizontal axis due to the bending moment of 899.5 Nm. Calculate the total force that is acting on the shaded portion of the cross-section of the beam. Cross-section of a beam y 0.8cm 4.6cm 0.8cm Зст 0.8cm 0.8cm
A telescope with tripod weighs 25 pounds and has geometry as shown in the figure and parameter table. Its center of gravity is at G and the ground can be considered to be a smooth surface. What are the vertical support reactions at A, B, and Č G В A L2 -3 y parameter value units 4.25 ft L2 La L4 1.75 ft 2 ft 1.5 ft The normal reaction at A is lb The normal reaction at B is lb The normal reaction at C is lb
Can you explain why there is value of Iy. This figure the ly placed on the centroid, but correct me or please correct me why there is value of Iy instead zero value. Thank you
Determine the moments of inertia of the Z-section about its centroidal xo- and yo-axes. 25 mm 135 mm Answers: Isa = i 100 mm- 25 mm -100 mm- 25 mm (106) mm² (105) mm²
Please help me find the reaction at B and the reaction at A (along with their directions). I have attached the magnitude and location of resultant just incase you need it, thank you!
2) Compare the natural frequencies and mode shapes of the following two structures. m k 2m k TI 2m k m k (b)
Q2: For the beam shown below in (fig 2), calculate the location of the centroidal axis ?̅, forthe cross-sectional area of the T-beam, after that find the moment of inertia I?̀ about the ?̀axis.
The beam is subjected to the distributed load and the couple shown. If M is slowly increased starting from zero, at what value M0 will contact at B change from the lower surface to the upper surface?
(a) (c) Question 7 The vertical deflection of node C for the truss shown in figure is 2 PL AE PL AE 3 PL AE (b) (d) PL 2 AE 60° 60° L 60° P
A prismatic uniform beam has a total length of 4L, a moment of inertia I, and a modulus of elasticity E. The beam is embedded at A, simply supported at B, and subjected to the distributed load q shown. Calculate:a) The reactions and moments in A and B.b) Deflection and slope at point C. You must indicate their directions.
Structural dynamics civil engineering Abody oscillates with simple harmonic motion along with the x-axis. Itsdisplacement varies with time according to x = 6 cos (πt + π/4), where (t) is inseconds and the angle is in radians.(a) Determine the amplitude, frequency and period of motion.(b) Calculate the velocity and acceleration of the body at any time t.(c) Using the results of (b), determine the position, velocity and accelerationof the body at t = 1 second.(d) Determine the maximum speed and acceleration.(e) Find the displacement of the body between t = 0 to t = 1 second.
Use the method of Slope-Deflection to find the reactions of the indeterminate continuous beam shown in the Figure. Assume that El is constant. 3.6 km 30- 60% 154 158 30ft Fixed