c) Cutting forces should be kept constant during machining operations to prevent changes in spindle speeds or work position. Such changes would deteriorate the accuracy of the work’s dimensions. A control system is proposed to control the cutting force. The plant is difficult to model, since the factors that affect cutting force are time varying and not easily predicted. However, assuming the simplified force control model shown in Figure Q2(c). (i) Show the closed-loop transfer function for the system of the system as below K(s+3) T(s)= s* +7s° +14s² + (8+K)s+3K

c) Cutting forces should be kept constant during machining operations to prevent changes in spindle speeds or work position. Such changes would deteriorate the accuracy of the work’s dimensions. A control system is proposed to control the cutting force. The plant is difficult to model, since the factors that affect cutting force are time varying and not easily predicted. However, assuming the simplified force control model shown in Figure Q2(c). (i) Show the closed-loop transfer function for the system of the system as below K(s+3) T(s)= s* +7s° +14s² + (8+K)s+3K

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter29: Dc Generators

Section: Chapter Questions

Problem 1PA: You are working as an electrician in a large steel manufacturing plant, and you are in the process...

See similar textbooks

Similar questions

1a) As depicted in the figure, input voltage is 120 Volts (RMS) and diode drops are 0.7 Volts. Design this circuit with given two outputs and calculate turns ratio of transformer. i) 10 V ii) 100 V
The definition of Current in machine
Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across Ri, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diode have? (Use constant voltage drop model for the Silicon diode) D1 IN4001 R. V out OV 10 kN D2 IN4001 llle
a) explain the principles of SMAW welding. b) explain the output slope of power source for SMAW c) explain the purpose of flux electrode of SMAW d) discuss two (2) types of covered electrode that are classified in SMAW process
Consider the circuit shown in Figure Q7. The full-wave bridge rectifier is supplied from a transformer that has a secondary winding resistance of 52. When conducting, each diode has a forward voltage drop of 0.7 V, regardless of the current carried. D1 D4 240 V rms 50 Hz D2 D3 RL Figure Q7 (a) The transformer has a turn ratio of 10:1. Find the value of the load resistance, RL, if the peak voltage across the load is found to be 20.0 V. (b) For a load resistance of 50 2 and a transformer that gives a peak current in the load of 0.5 A, what is the power dissipated in the load? n:1
1. It is a type of advanced machining process that uses highly pressurized water to cut nonmetallic materials. a. Abrasive water jet machining b. Abrasive jet machining c. Water jet machining d. Jet machining 2. Alternating Current Which if the following is NOT essential in electrochemical grinding. a. Electrolyte b. Electrode c. Abrasive particles d. Alternating current
Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across R, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diode have? (Use constant voltage drop model for the Silicon diode) D IN4001 R 10 kn IN4001
Q1 Figure Q1(a) shows a single phase half-wave controlled rectifier has a resistive load of R = 100, the voltage at the secondary transformer is 230V, and the firing angle of thyristor is 60°. Determine (i) The expression of average and rms load voltage The value of average and rms load voltage (i) (i) Average and rms load current (iv) Average output power (v) the new firing angle, a. if the rectifier is connected to the load which consumes 25% of the maximum possible average output voltage (vi) Draw the output voltage and current waveforms for the new firing angle a m sin wt Figure Q1(a)
Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across R1, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diode have? (Use constant voltage drop model for the Silicon diode) D IN4001 R1 V out 10 kN D2 IN4001 allle
You are working as an electrician in a large steel manufacturing plant, and you are in the process of doing preventive maintenance on a large DC generator. You have megged both the series and shunt field windings and found that each has over 10 M to ground. Your ohmmeter, however, indicates a resistance of 1.5 across terminals S1andS2. The ohmmeter indicates a resistance of 225 between terminals F1andF2. Are these readings normal for this type machine, or is there a likely problem? Explain your answer.
I need to power a 15kw/20HP DC Motor with a rectified 24VDC from a step down transformer with input of 11A and output of 103A/12VAC -24VAC. What is the required Capacitance needed to ensure ripples are cleared and also gives a steady VDC of 24VDC to the DC Motor to run quite well. Please, all note that the rectifier is a full wave rectifier of 100A...
- In d.c. generators armature reaction is produced by armature current O none of the mentioned compensating winding current field current O commutating winding current The use of d.c. generators elminated the use of rectifiers and ac supplies True False s If the number of layerallot is 4 then the number of colls the number of slots Equal to O none of the mentioned O twice O half O s In 2-pole machines: the wave winding have greater generated voltage than the lap winding'armatures True False For high rotating speed machines the number of poles munt be Little Tiue O Fale O O O