Bronze 2m Steel 1.0 m A 0.6 ml-1.0m- m-0.8 m 50 kN The figure shows a rigid bar that is supported by a pin at A and two rods, one made of steel and the other of bronze. Neglecting the weight of the bar, compute the stress in each rod caused by the 50-kN load, using the following data: Steel Bronze 600 300 Area (mm²) E (GPa) 200 83

Bronze 2m Steel 1.0 m A 0.6 ml-1.0m- m-0.8 m 50 kN The figure shows a rigid bar that is supported by a pin at A and two rods, one made of steel and the other of bronze. Neglecting the weight of the bar, compute the stress in each rod caused by the 50-kN load, using the following data: Steel Bronze 600 300 Area (mm²) E (GPa) 200 83

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.6P: The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular...

See similar textbooks

Similar questions

A flanged bolt coupling consist of 9 steel bolts evenly spaced around a bolt circle 300 mm. in diameter and 6 bronze bolts on a concentric bplt circle 200 mm. in diameter. What are the sizes of bolts diameters for steel and bronze, if the torque applied is 6,000 N-m and without exceeding the stress of 60 MPa in the steel and 40 MPa for the bronze? The ratio of the bolt diameter db / ds = 0.50. For steel, use Gs = 83 GPa and for bronze, Gb = 28 Gpa.
Situation 1: A rigid bar ABC weighs 10 kN/m. The compressive stress of the copper bar is 20 MPa. Answer the following questions: 3m B 2 m Copper L=3m A = 1500 mm² Brass C L = 2 m A = 1200 mm² A. What is the stress of the brass bar? Indicate if it will experience tension (T) or compression (C) (MPa) B. What is the minimum required diameter of the pin at A assuming that the pin connection is in double shear? Consider the allowable shearing stress of the pin as 15 MPa. Round your answer in a multiple of 5. (mm)
= 5.29 Knowing that P Q = 480 N, determine (a) the distance a for which the absolute value of the bending moment in the beam is as small as possible, (b) the corresponding maximum normal stress due to bending. (See hint of Prob. 5.27.) THEMOM DV P nedw to absol be500 mm 500 mm pripoly not Alase BOLERON 9T AO mersib anamorp sode bol ng appiled: the batuda Fig. P5.29 edi te ating out A Daniloobo CV. D (5.6b) Q f 12 mm s mas i nadw bozudiruaib ebimnice di Tibe sade 2b2 B (10. busd bus bris to pages. eda sdtlanbi are noe minnas li batalize yo led ditw i most u tamom gaiboedshus en betrovalmisoled loads Dignst Box brol 18 mm
An aluminum rod is rigidly attached between a steel rod and a bronze as shown. Axial loads are applied at the positions indicated. Find the stress of each rod in MPa. Steel Aluminum Bronze A- 500mm A = 400mm? A- 200mm 40KN 10KN 20KN 1.5m 2.5m 2.0m Determine the change in length of steel rod having a length of 800mm and a diameter of 6.5mm. The rod is subjected to a force P equal to 110KN. Young's Modulus is 200GPA Compute normal strain of the rod
A compressive load P is transmitted througha rigid plate to three magnesium-alloy bars that areidentical except that initially the middle bar is slightlyshorter than the other bars (see figure). The dimensionsand properties of the assembly are as follows:length L = 1.0 m, cross-sectional area of each barA = 3000mm2, modulus of elasticity E = 45 GPa,and the gap s = 1.0 mm.(a) Calculate the load P1 required to close the gap.(b) Calculate the downward displacement d of therigid plate when P = 400 kN.(c) Calculate the total strain energy U of the threebars when P = 400 kN.(d) Explain why the strain energy U is not equal toPδ / 2. Hint: Draw a load-displacement diagram.
A round bar made of same material consists of 3 parts each of 100 mm, length having diameters of 40 mm, 50 mm and 60 mm respectively. If the bar is subjected to an axial load of 10 kN, the total elongation of the bar would be (E is the modulus of elasticity in KN/mm². (a) 4/1 1 1 + + (b) TE 16 25 36 (c) 1 0.4 1 1 + wwwwww + TE 16 25 36 (d) 4√2/1 1 1 www + wwwwwww + TE 16 25 36 40/1 1 1 + TE 16 25 36 — ===== + — mm mm mm mm
ok Strength of Materials donO نورا حياتها مترجر شریه ✓t مقادم نلود Dr. Mohammed Hashim Mohammed Problems tan't yorada grutegraat km). E1.x² (1) A steel rod with cross-sectional area of 150mm² is stretched between two fixed points. The tensile load at 20°c is 5 kN. What will be the stress at -20°c? At what temperature the stress will be zero? bedre α = 11.7x10 6/2 and E = 200x10² N/m².
Brass. (c). A bar of length 1000 mm and diameter 30 mm is centrally bored for 400 mm, the bore diameter being 10 mm as shown below. Under a load of 30 kN, if the extension of the bar is 0.222 mm, what is the modulus of elasticity of the bar? mam um
An aluminum rod is rigidly attached between a steel rod and a bronze as shown. Axial loads are applied at the positions indicated. Find the stress of each rod in MPa. Steel Aluminum Bronze A- 500mm? A = 400mm? A - 200mm 40KN 10KN 20KN 2.5m 2.0m 1.5m
!! Show Complete & Detailed Solution w/ FBD !!The figure shows that when the rigid bar is in the horizontal position, the wires are unyielding. The bar rotates clockwise about the pin B through an angle of 2.1° when a force is applied at the handle. Determine the average normal strain developed in wires.a. AHb. CGc. DF
Bar A was manufactured 2 mm less than bar B due to an error. The attachment of these bars to the rigid bar wouldcause a misfit of 2 mm. Calculate the initial stress in each assembly. Which of the two assembly configurationyou would recommend? Use modulus of elasticity of E = 80 GPa and diameter of the circular bars as 32 mm.
Two plate are joint by five rivets of 20 mm diameter. What is the shear stress in the material if the shear forces is 18840 N O 12 N/mm2 O 20 N/mm2 O 15 N/mm2