Home work:1- A belt 100 mm wide and 8 mm thick are transmitting power at a belt speed of 160 m/ minthe angle of lap for smaller pulley is 165 ° and the coefficient of friction 0.3 , the max-kg/m, find the powerpermissible stress 2 m2MNand the mass of the belt is 0.9 r

T1T2 = eμθ = e0.3 × 2.88 = 2.372 ---- (a)Tc = m v2 = 0.9 × 26.672 = 640 N

Answered: belt 100 mm wide che angle of lap for…

Engineering

Mechanical Engineering

belt 100 mm wide che angle of lap for ermissible stress

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Flat belt 100mm wide and 8mm thick transmits power between two pulleys, running at 1600 m/min. The mass of belt is 0.9kg/m length, the angle of lap in the smaller pulley is 165o and the coefficient of friction between the belt and pulleys is 0.3, If the maximum permissible stress in the belt is 2MN/m2, find the maximum power transmitted.
An open belt 100 mm wide connects two pulleys mounted on parallel shafts with their centres 2.4 mapart. The diameter of the larger pulley is 450 mm and that of the smaller pulley 300 mm. The coefficient of friction between the belt and the pulley is 0.3 and the maximum stress in the belt is limited to14 N/mm width. If the larger pulley rotates at 120 r.p.m., find the maximum power that can be transmitted
Flat belt 100mm wide and 8mm thick transmits power between two pulleys, running at 1600 m/min. The mass of belt is 0.9kg/m length, the angle of lap in the smaller pulley is 1650 and the coefficient of friction between the belt and pulleys is 0.3, If the maximum permissible stress in the belt is 2MN/m2, find the maximum power transmitted. 1 Add file
1. A single-threaded 25-mm power screw is 25-mm in diameter with a pitch of 5mm. A vertical load on the screw reaches a maximum of 5 kN. The co-efficients of friction are 0.06 for the collar and 0.09 for the threads. The frictional diameter of the collar is 45-mm. Find the overall efficiency and the torque to "raise" and “lower" the load.
An open belt 100 mm wide connects two pulleys mounted on parallel shafts with their centres 2.4 m apart. The diameter of the larger pulley is 450 mm and that of the smaller pulley 300 mm. The coefficient of friction between the belt and the pulley is 0.3 and the maximum stress in the belt is limited to 14 N/mm width. If the larger pulley rotates at 120 r.p.m., find the maximum power that can be transmitted. [Ans. 2.39 kW]
Saved A single-threaded power screw is 25 mm in diameter with a pitch of 5 mm. A vertical load on the screw reaches a maximum of 5 kN. The coefficients of friction are 0.05 for the collar and O.15 for the threads. The frictional diameter of the collar is 62 mm. Find the overall efficiency and the torque to raise and lower the load. The overall efficiency is The torque to raise the load is The torque to lower the load is %. kN-mm. kN-mm. nt rences Next > 1 of 2 Prev
A 750 mm steel pulley transmits 120 hp at 700 rpm. The arc of contact between the belt and pulley is 152 degrees, the coefficient of friction between belt and pulley is 0.30 and the safe working stress of the belt is 2.0 MPa. Find the width of the belt used in mm if its thickness is 20 mm.
The following data is refers to a screw jack. The vertical load on the screw320kN Force applied at the lever end whose length=80cm The mean radius of the screw=2.5cm Pitch of the screw=1cm Co-efficient of friction between the screw thread and the nut=0.15 Determine the force on the lever end while raising the load and efficiency of the screw jack
A plate clutch has 3 discs on the driving shaft and 2 discs on the driven shaft, providing four pairs of contact surfaces. The outside diameter of the contact surfaces is 240 mm and inside diameter 120 mm. Assuming uniform pressure and coeff. Of friction is 0.3. Find the total spring load pressing the plates together to transmit 23kw power at 1475 revolution per minute. If there 6 springs each of stiffness 13 kN/m and each of the contact surfaces has worn away by 1.25 mm. find the maximum power that can be transmitted assuming uniform wear. A plate clutch has 3 discs on the driving shaft and 2 discs on the driven shaft, providing four pairs of contact surfaces. The outside diameter of the contact surfaces is 240 mm and inside diameter 120 mm. Assuming uniform pressure and coeff. Of friction is 0.3. Find the total spring load pressing the plates together to transmit 23kw power at 1475 revolution per minute. If there 6 springs each of stiffness 13 kN/m and each of the contact surfaces…
3. The safe working stress of a belt is equal to the tight side tension over the product of the belt's width and thickness. Find the width of the belt if a 610mm diameter pulley transmits 40 kW at 500 rpm, the arc of contact is 144°, coefficient of friction is 0.35, safe working stress of the belt is 2.1 MPa and thickness is 6mm.
Q2 ) A cone clutch is to transmit 10 KW at 600 r.p.m. the cone has aface angle of 10◦The width of the face is halfe of the mean radius and the max pressureis 0.1 N/mm²Assuming uniform wear and the coefficient of friction is 0.3, find theinner and outer radius and the axial force required on the clutch.
The following data is referring to a screw jack. The vertical load on the screw = 20kN Force applied at the lever end whose length = 80cm The mean radius of the screw = 2.5cm Pitch of the screw =1cm Co-efficient of friction between the screw thread and the nut = 0.15 Determine the force on the lever end while raising the load and efficiency of the screw jack