Basically, there are four types of Portland cements. Which one of the followings is more suitable for cold weather? a. Type C: Low heat cement b. Type A: Normal Portland Cement Oc. Type B: High early strength Od. Type D: Sulphate resisting cement

Basically, there are four types of Portland cements. Which one of the followings is more suitable for cold weather? a. Type C: Low heat cement b. Type A: Normal Portland Cement Oc. Type B: High early strength Od. Type D: Sulphate resisting cement

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter12: Composite Materials

Section: Chapter Questions

Problem 27CQ

See similar textbooks

Related questions

Q: A runway at a commercial service airport maintains non-precision instrument procedures with…

A: Given that :-With visibility requirements as low as mile, a runway at a commercial service airport…

Q: P15.39 The tube shown in Figure P15.39/40 has an outside diameter of 3.50 in., a wall thickness of…

A: Given dataFindprincipal stresses on the side of the tube at point K

Q: What is PostScript, and how does it contribute to high-quality printing? Provide examples of its…

A: PostScript is a page description language (PDL) developed by Adobe Systems. It's a programming…

Q: Hydration of cement is exothermic process that generates heat. The table below shows the heat…

A: Option-a:This option implies that utilizing any of the specified cement components is unsuitable for…

Q: A FRP composite includes 40% continuous and aligned Aramid fibers by vol-ume. The moduli of…

A: Modulus of elasticity of polymer(Em)=3.9GPaModulus of elasticity of fibre(Ef)=130GPa

Q: members are in tension or compression. Assume all members are pin connected. 3k 4 ft 4 ft 2 k A G 6…

Q: Problem 5. For the compound beam shown in the figure, draw the shear force and bending moment…

A: Given:Required:Shear and moment diagram

Q: For the simply supported displacements at E and C. values along the member

Q: Type 11/111 sedimentation analysis: A laboratory settling test was performed on a suspension…

A: The extent of treatment required to be given to a particular water depends upon the characteristics…

Q: Using

Q: Problem 1: Calculate M, for each beam then briefly discuss the impact of each variable on the…

A: Beam…

Q: The diameter of a pipe is 200 mm. The velocity .. of flow through the pipe is 4 m/s. The discharge…

Q: F 29 E 29 * Find: reactions & Force in all members a 9

Q: 3. Determine the reaction at the hinge support at point A and roller support at point B. A W=2 N/m…

Q: DESIGN FOR TENSION ONLY (ACI METHOD fe=21mPa fy=276 MPa Strength Design 2015 NSCP SPAN 1: DL= 8 KN 름…

Q: A.) the plastic section modulus and the plastic moment Mp. Bending is about the x-axis, and the…

A: Given:Required:Plastic section modulus and plastic moment

Q: PROBLEM 2 The section shown carries a maximum moment of 120 kN-m, compute the maximum bending stress…

A: Given data - M = 120 KN-m Find out -Calculate the maximum bending stress ?

Q: An 8 m long steel is simply supported at the left end and 2 m from the right end. It carries a total…

A: To determine the maximum web shear stress of the beam, we need to calculate the shear force at the…

Q: SITB. Determine the reactions (kN or kNm) at A, B, C, and D. 5kN 10kN/m ↓ A ЧЕТ 4m B 2m 2 ET 2m с ET…

A: To find the reactions at the beam supports.

Q: Q.4) A machine part is subjected to four forces and three couple moments as shown. The part is to be…

A: Given:Required:Location of rivet hole somewhere along the horizontal line between A and B

Q: At an entrance to a toll bridge, four toll booths are open. Vehicles arrive at the bridge at an…

A: Vehicle rateTime, To find: Average queue length if fifth tool booth were opened.

Q: The wet density of soil mass= 1800 kg/m³ and the dry mass=90kg. If the w = 10 % and G₁ = 2.6,…

Q: 2. Determine the reaction at the hinge support at point A and roller support at point B, which is…

Q: Problem #2 Determine: the reactions at A and B when (a) a = 0, (b) a = 90°, (c) a = 30°. 300 mm 330…

Q: The following net accumulations were calculated. The free haul area begins at station 4+30 and…

A: Stations are horizontal measurements along the center line (also called baselines) of a project.…

Q: Consider the warren truss below, assume all members are pin connected and use W8x13 for member…

Q: 8. Design a column with an effective length of 20 ft to support a dead load of 75 k, a live load of…

Q: The dead weight tester has been used to calibrate a pressure gage. After finishing the calibration…

Q: *7-12. Determine the slope and the displacement at C. EI is constant. Use the moment-area theorems.…

A: EI = ConstantDetermine the slope and deflection at C using Moment-Area method.

Q: 5) In contrast to the Greenshield's model of traffic flow that considers a linear relationship, the…

A: Given that :-The Greenberg model of traffic flow assumes a non-linear relationship between…

Q: Three locations are supplied with a big water tank. Determine the flow rate at the pipes and at the…

A: Given that :-Cross-sectional area of pipes and exits (A₁ = A₂ = A₃ = A₄ = A₅) = 0.01 m²Heights of…

Q: P2: The structures below are unstable. Alter the supports or internal configurations as described to…

Q: A -4 ft- 8 ft- 3 k/ft B 8 ft C 4 ft

A: Given data,Continuous beam is given FINDBending moment diagram.

Q: Design a rectangular beam for a 5 m simple span to support a uniform dead load of 12 kN/m and…

A: The span of beam = 5 m Uniform dead load = 11kN/m Uniform live load = 20kN/m fc' = 20 MPa fy = 400…

Q: Assume that the top of a round sprue has a diameter of 100 mm and has a height of 300 mm. At the…

A: top dia(D)=100mmbottom dia(d)=25mmheight(h)=300mm

Q: Describe in detail the phases or stages involved in the Wilson approach, and discuss the activities…

A: given data,question given related to the managementLet's discuss about the detail the phases or…

Q: Problem 3 A Determine the maximum flexural stress (MPa) developed for the beam loaded as shown.…

Q: Design a flexible pavement (granular pavement with thin bituminous surfacing) for the given…

A: Given that :-Design traffic = 6,000,000 ESACBR = 1.5Use a sprayed seal surfacing layer of less than…

Q: What is the purpose of sensors in perimeter and building security?

A: Given data,question given related to the sensors and building security.Let's discuss the purpose of…

Q: Can you recheck the k1= 55m from this figure. Thank you so much.

Q: Results of traffic flow studies on a highway indicate that the flow-density relationship can be…

A: The given data is shown below:

Q: A soil sample having a void ratio of 1.3, water content of 50% and a specific gravity, 2.60, is a…

A: Void ratio = 1.3 Water content = 50 %Specific gravity = 2.60To Find :State of Soil sample ?

Q: Determine the maximum axial force developed in members ID, DE, and KL of the truss shown below due…

Q: (Note: @ does not include beam weight) @D = 2 kip/ft @= 4 kip/ft 12 ft P₁ = 10 kips (A) f = 5,000…

A: Longitudinal section of the beam:Cross-section of beam

Q: If a W27X84 beam is coped 2” in depth and at a length of 5” with a ½” gap between the member and the…

A: beam:

Q: Determine the reactions at the supports for the structures shown

Q: -12 ft- 80 lb/ft 600 lb -12 ft-

Q: A 1 in diameter rod decreases in length by 0.001 inches when subjected to a 4,893 kip load. If the…

A: Diameter of the rod (d) = 1in. Decreases length of the rod (∆L) = 0.001 in. Load (P) = 4893 Kips Rod…

Q: Problem #2 The bar shown below has uniform cross section and material properties throughout. In…

Q: Required information NOTE: This is a multi-part question. Once an answer is submitt Warren bridge…

Concept explainers

Reactions with Materials

Limestone

Question

Basically, there are four types of Portland cements. Which one of the followings is
more suitable for cold weather?
a. Type C: Low heat cement
b. Type A: Normal Portland Cement
Oc. Type B: High early strength
d. Type D: Sulphate resisting cement

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Explenation to Options

VIEW

Step 2: Explenation to Options

VIEW

Solution

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The composition of a certain brand of cement is given (C3S = 16.0%, C2S = 38.0%, C3A=11.0% and C4AF = 8.0%) the type of cement is Ordinary Portland cement Sulphate resisting cement Low heat cement Rapid hardening cement Which cement is used for mainly building construction where strength required with age. Rapid Hardening Cement Low Heat Cement Quick Setting Cement Portland Pozzolana Cement
Main Compounds of Portland Cement
Which compound of cement is responsible for strength of cement? a. Magnesium oxide b. Silica c. Alumina
The relative amounts of the four chemicals in the final cement depends on the desired properties of the cement concrete. The table below gives the typical compound composition of different types of Portland cements Compound Composition No. C3S C,S C3A C4AF 1 60 13 9. 8 40 40 4 3 26 50 5 12 4 50 24 11 5 42 33 5 13 Depending on the properties of the different chemicals and their relative composition, identify the high early strength (HE) and low-heat (LH) cements from the table. Give detail explanation for your answer
Which cement is used for mainly building construction where strength .required with age Rapid Hardening Cement Quick Setting Cement Low Heat Cement Portland Pozzolana Cement The composition of a certain brand of cement is given (C3S = 53.0%, C2S = 18.0%, C3A-12.0% and C4AF = 8.0%) the type of cement is i need clear ans and solve very very fast in 20 min and thank you | DYBALA 4 Sulphate resisting cement Ordinary Portland cement Low heat cement Rapid hardening cement
The composition of a certain brand of cement is given (C3S = 53.0%, C2S = 18.0%, C3A=12.0% and C4AF = %3D 8.0%) the type of cement is * Sulphate resisting cement Rapid hardening cement Ordinary Portland cement Low heat cement For the If the chemical composition of cement is as follows (CaO=60%, SIO2 =25.6%, Al2O3= 3.8%, MgO=4%, SO3=2.1%, C4AF=13.7%) the type of cement is * White cement None of the above Expansive cement Pozzolanic cement
In designing a concrete mix, if the amount of mixing water is estimated at W = 185 Kg/m, the SSD weight of the coarse aggregate is 1045 Kg/m, and the SSD weight of the fine aggregate is 617 Kg/m. The coarse aggregate has a moisture content of 1% and an absorption capacity of 2%. The fine aggregate has a moisture content of 2% and an absorption capacity of 5%. The adjusted weight of mixing water (in Kg/m³) is: O 177 O 214 156 193 O 172 O O O O O
Which of the following material is/are used as an accelerator’s additive for cement? a. Sodium Chloride b. Caustic Soda c. Calcium Chloride d. Nitrogen e. Barite f. Bentonite g. Gypsum
Although the constituents of concrete (aggregate and hydrated cement paste) behave in a linear elastic manner if stress is applied to them and the resulting strain is measured, concrete is not a linear elastic material throughout its entire stress-strain curve. What is the main reason for the deviation from this behavior? Interfacial transition zone (ITZ) Incomplete hydration of cementitious phases The loading rate applied according to ASTM C 39 presence of C-S-H very close to the aggregate/paste interface
The composition of a certain brand of cement is given (C3S = 16.0%, C2S = 38.0%, C3A-11.0% and C4AF = 8.0%) the type of cement is Rapid hardening cement Low heat cement Sulphate resisting cement Ordinary Portland cement
The composition of a certain brand of cement is given (C3S = 53.0%, C2S = 18.0%, C3A-12.0% and C4AF = 8.0%) the type of cement is i need clear ans and solve very very fast in 20 min and thank you | DYBALA Sulphate resisting cement Ordinary Portland cement Low heat cement Rapid hardening cement
Which of the following materials is/are a good weight additive for cement (include both weight increase and weight reduction)? a. Bentonite b. Barite c. Hematite d. Sand e. Nitrogen