(Barbir Chp6 Problem 4) A fuel cell has 100 cm? active area. Air at the inlet is fully saturated at 60°C. Pressure at the inlet is 200 kPa, and there is a 15 kPa pressure drop through the flow field. Oxygen stoichiometric ratio is 2.5. Calculate the heat generated at 0.65V and 1 A/cm? by (i) assuming energy of fuel (higher heating value) is converted into electricity and heat and (ii) by doing a detailed mass and heat balance analysis (assume hydrogen is supplied in dead-end mode saturated at 60°C and that net water transport through the membrane is such that there is no water accumulation on the anode side). (Answer: 83.2 W. 85.13 W)

(Barbir Chp6 Problem 4) A fuel cell has 100 cm? active area. Air at the inlet is fully saturated at 60°C. Pressure at the inlet is 200 kPa, and there is a 15 kPa pressure drop through the flow field. Oxygen stoichiometric ratio is 2.5. Calculate the heat generated at 0.65V and 1 A/cm? by (i) assuming energy of fuel (higher heating value) is converted into electricity and heat and (ii) by doing a detailed mass and heat balance analysis (assume hydrogen is supplied in dead-end mode saturated at 60°C and that net water transport through the membrane is such that there is no water accumulation on the anode side). (Answer: 83.2 W. 85.13 W)

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter30: Dc Motors

Section: Chapter Questions

Problem 6RQ: What is CEMF?

See similar textbooks

Similar questions

A triac can pass a portion of …………… half-cycle through the load a. neither positive nor negative b. both positive and negative c. only negative d. only positive
DA shunt generator is used to charge a battery of 100 cells in series. If each cell has a terminal p.d. of 2.5V at the completion of charge and is of internal resistance 0.001 Q calcu- Cate the e.m.f. to be generated to give a charging current of 15A at the end of charge. Assume that the armature and field resistances are 0.2 2 and 200 2 respectively and the cables onnecting the generator to the battery have a resistance of 0.6 Q.
When the capacitance is increased, what is the effect on the charging and discharging times? What is the mathematical relationship between duration and capacitance?
Draw the energy band diagram based on the following diffusion gradient condition. Show the directions of diffusion current (Ilan) and drift current (lain) on the energy band diagram. E No EF
Which of the following statement is true? a. Angle between load voltage and load current in a pure capacitive load is 45 degree. b. Angle between load voltage and load current in a pure capacitive load is is 180 degree. c. Angle between load voltage and load current in a pure capacitive load is is zero. d. Angle between load voltage and load current in a pure capacitive load is is 90 degree.
7. Each of three insulators forming a string has self-capacitance of "C farad. The shunt capacitance of each cap of msulator is 0 25 C to earth and 0-15 C to line. Calculate the voltage distribution across each insulator as a pecentage of line voltage to earth and the string efficiency.
Describe in words how you want to control the electric fields in a capacitor bushing and where we use such bushings.
Please choose the correct answer and explain if possible. Thank you. 4. The main terminal voltage across an ON conducting SCR depends on the instantaneous main terminal current in the following way: a. They are proportional b. The voltage increases as the current increases, but no quite proportionally c. The voltage increases as the current increases, by a squared (seond power) relationship d. They are virtually non-related 5. To turn Off a conducting SCR in a dc-powered circuit, it is necessary to: a. Interrupt (stop) the gate current b. Wait for the main terminal current to fall below IHO when the supply voltage crosses through zero c. Deliver a pulse of negative gate current via the gate lead d. Place a temporary reverse bias across the SCR’s main terminals 6. In a simple RC charging circuit used for trigger-control of an SCR, a good range of adjustment of the RC time-constant is: a. 1 to 5 msec b. 1 to 30 msec c. 0.1 to 10 msec d. 2 to 25 μsec
A step-up chopper has input voltage of 220 V and output voltage of 660 V. If the conducting time of the IGBT based chopper is 100 micro- sec, then duty cycle will be a. -0.66 b. 0.7 c. 1.66 d. 0.66
Subject Linear Control I need answer for MCQ
6. What do you understand by Ferranti effect?
A voltage reflection coefficient is measured as 0.75 , and the correspondingload voltage is 1 V. Determine (a) the incident voltage component at the load , (b) the reflected voltage component at the load , and (c) the current reflection coefficient