bar is produced from water at (12263kJ) ive kg of eam at pressure of the amount of heat supplied if the steam is 0.9 dry. 7-One kg of water at 47.8°C is heated under constant pressure of 13.7bar until it is converted into steam with 111°C degree of superheated. Determine the quantity of heat supplied during superheating and the total heat. (268kJ, 2852kJ) etermine

bar is produced from water at (12263kJ) ive kg of eam at pressure of the amount of heat supplied if the steam is 0.9 dry. 7-One kg of water at 47.8°C is heated under constant pressure of 13.7bar until it is converted into steam with 111°C degree of superheated. Determine the quantity of heat supplied during superheating and the total heat. (268kJ, 2852kJ) etermine

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

13. A gas is transferred to an empty 0.7m3 cylinder until the pressure reaches 9MPaa. The temperature of the gas is 62°C. If the cylinder mass increases by 5.37kg after the gas has been added, calculate the value of the gas constant. a. 3.5334kJ/kg-K b. 3.5005KJ/kg-K c. 3.5020kJ/kg-K d. 3.4901kJ/kg-K 14. A 30ft x 5ft diameter storage tank containing water at its maximum level is being drained by a drain valve located at the bottom of the tank. It was seen that the velocity of exit water changes as the height of the water level in the tank. At the instant the water level is at 12ft from the bottom of the tank, determine the instantaneous time required to empty the tank if the drain pipe diameter is 26mm. a. 24.7184mins. b. 25.7277mins. c. 22.5647mins. d. 24.4060mins. 15. In a 6L storage, a gaseous compound is stocked weighing 0.782g at 19°C and 617mmHg. When the condition is at STP, find the density given by g/L a. 0.9475g/Li b. 0.9288g/Li c. 0.9595g/Li d. 0.9439g/Li 16. A bullet with a…
What is the internal energy of 2.2 kg of dry saturated steam at 11 bars ?
Steam at 3.2 MPa and with 77.49⁰C SH rejects 1975 kJ/kg of steam heatat constant pressure. Determine the following in SI units:a. Initial temperatureb. Final temperaturec. Wd. Δse. Δu
d. A rigid vessel of volume 1 m3 contains steam at 20 bar and 400°c. The vessel is cooled until the steam is just dry saturated. i. Calculate the mass of steam in the vessel. ii. Determine the final pressure of the steam. ii. Determine the heat removed during the process.
0.25gm/sec of wet steam with 0.6MPa and dryness faction of 0.96 undergoes an isochoric process until it becomes saturated. Determine its dS, dH, Q, Wsf, and dU.
PROBLEM 2. A certain gas with cp = 0.53 Btu/lb°R and R = 96 ft-lb/lb°R, expands from 6 ft3 and 90°F to 16 ft^3 while the pressure remains constant at 40 psia. Compute the final temperature in deg F. 550 O 1050 O 1810 O 1490 O 200
QUESTION 37 In an experiment, a certain amount of air is heated at constant pressure from 1.7 m³, 38 °C and 97 kPa to 415 UC. It is then cooled at constant volume back to its initial temperature. Calculate the change specific entropy in the cooling process in the correct unit in SI and 1 decimal place. Take Specific heat at constant pressure and constant volume for 0.717 kJ/kg K air as 1.004 kJ/kg K and respectively. add units. I decimal place.
1.2kJ of work was done on a DIATOMIC ideal gas in a PERFECTLY INSULATED container. A. How much heat energy was transferred? B. What is the change in the internal energy of the system? C. Will the temperature increase or decrease during this process, and how much? D. What is the change in enthalpy?
1. A steel flask of 0.04 m³ capacity is used to store Nitrogen at 120 bar and 20°C. The flask is protected against excessive pressure by a fusible plug which will melt and allow the gas to escape if the temperature is too high. A. How many kilogram of Nitrogen will the flask hold at the design conditions? B. At what temperature in °C must fusible plug melt in order to limit the pressure of flask to a maximum of 150 bar?
B2. The heat energy of 1605 kJ is supplied to saltwater in the steam generator to heat from 25°C to 104°C for the generation of water vapor, Take the density & specific heat of the solution as 1028 kg/m³ & 3 J/kg°K respectively. Determine the quantity of saltwater in the steam generator. I Solution: i) Change in Temperature (in K) ii) Mass of the saltwater (in kg) iii) Quantity (Volume) of salt water (in m³)
Identify the working substance, specify the kind of system and sketch the system boundary. PLEASE ANSWER it in 1hr.
Solve the following questions using Steam Table: 1. Determine T, h, s, u and v of saturated steam of 1.4Mpa except that it has a °SH of 100°C.2. Given: P = 2.47 Mpa and T = 384°C Find: h