B1 a) b) c) The simply supported beam in Fig QB1a is made by gluing two pieces of wood of rectangular cross-section as shown in Fig QB1b, i.e. the top board (flange) is glued onto the bottom board of the web. The supports at A and B exert only vertical reactions. 150mm y 30mm A 4m C 30mm 150mm 6.5 kN/m Fig QB1a 4m B y = 0.120m Fig QB1b Calculate the support reaction forces, and hence sketch shear and bending moment diagrams indicating the values at A, B, C. Describe how shear force and bending moment vary along the beam; Compute the moment of inertia of the section about the neutral axis. The position of the neutral axis is y = 0.120m as shown in Figure QB1b; Determine the maximum shear stress in the glue necessary to hold the beam together along the seam where they are joined.

B1 a) b) c) The simply supported beam in Fig QB1a is made by gluing two pieces of wood of rectangular cross-section as shown in Fig QB1b, i.e. the top board (flange) is glued onto the bottom board of the web. The supports at A and B exert only vertical reactions. 150mm y 30mm A 4m C 30mm 150mm 6.5 kN/m Fig QB1a 4m B y = 0.120m Fig QB1b Calculate the support reaction forces, and hence sketch shear and bending moment diagrams indicating the values at A, B, C. Describe how shear force and bending moment vary along the beam; Compute the moment of inertia of the section about the neutral axis. The position of the neutral axis is y = 0.120m as shown in Figure QB1b; Determine the maximum shear stress in the glue necessary to hold the beam together along the seam where they are joined.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

How many zero force members are there in the truss shown? F. [E Hl100 '1 60 VKN kN 60 ♥kN Select one: O a. 4 O b. 2 О с. 1 O d. 3
Draw the SFD and BMD for the following frame. 120 KN 30 kN/m 60 KN 8 m A >>> 3 m 1 m B 6 m
Given is a truss structure: Where: Working shear stress for the rivets is 70 MPa Working bearing stress due to rivets is 140 Mpa Thickness of the member is 5 mm Thickness of the Gusset plate is 6 mm Rivet diameter is 15 mm Determine the no. of rivets to fasten the member BD 80 kN 120 kN B. 3 m E 200 kN 4 Panels @ 4 m = 16 m
A steel beam having a span of 14 m. carries a dead load concentrated load Pp = 60 kN at its midspan. The beam is laterally supported at its span. Properties of the wide flange section. rts - 104.39 mm ho - 338.08 mm Jo -1.69 x 10^6 Cw - 4.3 x 10^12 d=356.11 mm tf = 18.03 mm tw - 11.18 mm Sx - 2343 x 103 mm rx = 155.96 mm ry - 93.98 mm Sy = 818 x 10^3 mm Zx = 2573 x 10^3 mm Zy= 1239 x 10^3 mm Fy = 345 MPa Iy = 151 x 10 mm Lp=3.98 Lb=14m Lr=12.98 Cb=1.14 Determine the safe concentrated live load that the beam could support at the center based on its design strength
The cantilevered W530 x 150 beam shown is subjected to a 7.5-kN force F applied by means of a welded plate at A. Determine the equivalent force-couple system at the centroid of the beam cross-section at the cantilever O. 0.58 m -5.3 m- 7280 F
What is most nearly the internal forces on member FG in the truss shown below 3 ft 5k B A fe-handbook-10-1.pdf O FG = 1.67 k (C) O FG = 13.33 k (T) O FG = 8.33 k (T) O FG = 20 K (C) 5k C D 10 k E F 4 @ 4 ft = 16 ft 5k G. H 5k I
Where is/are the location(s) of the maximum transverese shear stress? A simple I-beam is loaded as shown. 20 mm P KN PKN PKN Į Į -C B с D L/4 m L/4 m Midspan at point C Roller at E at the NA Section B at the top fiber Pin A at point C Midspan at point D Roller E at point D L/4 m L/4 m OE 20 mm 20 mm- 250 mm 150 mm 150 mm A
The cantilevered W530 x 150 beam shown is subjected to a 7.5-kN force F applied by means of a welded plate at A. Determine the equivalent force-couple system at the centroid of the beam cross-section at the cantilever O. 0.58 m -5.3 m- 28 Answers: F = i+ i j) kN Mo = k kN-m
Principle of superposition The beam is indeterminate to the first degree. Force in member BD is chosen as the redundant. This member is therefore sectioned to eliminate its capacity to sustain a force. 60 kN/m 3 m 1.8 m 60 45 actual structure (a) 160 kN/m B FaD redundant рrimary structure ARD FRp applied Fap D
Note: Attempt Five Quest Q1: Specify the type of the truss shown in Fig.(1). Then, find the forces in bars FK and JH. 3.0 m 3.0 m A i 50KN B N o 100KN K 120ml-20-13.0-2.0-12,0 -
(1)Consider the truss loaded and supported As shown Force (KN) T/C Member 3 m3m --4 m--4 m---4 m- (1) AB (2) AC (3) BD (4) BC (5) CD (6) DE (7) CE (8) EF (9) GE (10) 1.75 KN 2kN 1.5 IN 2IN 0.75 IN 6m -6 m .6m G (11)GF (12)H,
Classify structurc shown bclow as stablc or unstablc. If stablc, dcterminc whcther statically determinate or statically indeterminate. Explain your reasoning. If statically indeterminate, specify the degree of statical indeterminacy. Telles lixed