(b)The circuit in Figure Q2 (b) below shows a rectifier circuit where Vin is a10kHz sine wave with an amplitude of 2Vpp and RL is 10k.(i)(iii)The componet between A and B is a PN diode, sketch and label itssilicon structure and explain its characteristics.Sketch the waveforms you would see at A and B and explain or sketchhow you would connect your scope probes to measure them. Labelyour sketches clearly showing values and axis details.Comment on any similarities or differences between the waveforms atA and B. VinAFigure Q2 (b)BWWRL

Given Data: An uncontrolled Half wave diode rectifier with, Input peak-to-peak voltage Vpp=2 V Load…

(b) The circuit in Figure Q2 (b) below shows a rectifier circuit where Vin is a 10kHz sine wave with an amplitude of 2Vpp and RL is 10k02. (i) The componet between A and B is a PN diode, sketch and label its silicon structure and explain its characteristics. (ii) (iii) Sketch the waveforms you would see at A and B and explain or sketch how you would connect your scope probes to measure them. Label your sketches clearly showing values and axis details. Comment on any similarities or differences between the waveforms at A and B.

(b) The circuit in Figure Q2 (b) below shows a rectifier circuit where Vin is a 10kHz sine wave with an amplitude of 2Vpp and RL is 10k02. (i) The componet between A and B is a PN diode, sketch and label its silicon structure and explain its characteristics. (ii) (iii) Sketch the waveforms you would see at A and B and explain or sketch how you would connect your scope probes to measure them. Label your sketches clearly showing values and axis details. Comment on any similarities or differences between the waveforms at A and B.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

How is a solid-state diode tested? Explain.
What is the difference between a diode and rectifier?
Q1/ a/Draw the output voltage waveform for the bridge rectifier in this figure : 5:1 D Da 120 V ms Dy RL B/ What PIV rating is required for the diodes in a bridge rectifier that produces an average output voltage of 50 V? Q2/ Determine the minimum input voltage required for regulation to be established in the figure. Assume an ideal zener diode with Izx = 1.5 mA and V, = 14 V. lllee 幸
Q1/ a/Draw the output voltage waveform for the bridge rectifier in this figure : D D4 120 V ms D D2 R3 Vout B/ What PIV rating is required for the diodes in a bridge rectifier that produces an average output voltage of 50 V? Q2/ Determine the minimum input voltage required for regulation to be established in the figure. Assume an ideal zener diode with IzK = 1.5 mA and Vz= 14 V. R 560 N VIN
You are asked to design a de power supply using a bridge full wave rectifier, as shown in Figure 1.d, to deliver a de voltage of Vo 12 V to a 3 kQ load resistor with a ripple of less than 0.6 Vpp, where Vpp is the peak to peak voltage. The input voltage is a sine wave with frequency of 50 Hz. The diodes have a forward voltage of 0.7 V. i) Calculate the value of smoothing capacitor C. ii) Calculate the rms value of the input voltage, v(t).
Draw the changes in Vi and Id of the ideal diode half-wave rectifier circuit in the figure. The frequency of the sine signal here will be taken as 50Hz. (Changes in Vi and Id will be drawn!!!)
For the rectifier in the figure below, state the conduction sequence of the diodes for periods t1 to tó. D1 D2 D3 22) tl: D. & D.. 23) t2: D. & D.. 24) t3: D. & D.. 25) t4: D. & D.. D4 D5 D6 26) t5: D. &D. 27) t6: D.AN A & D....... Vm cot t6
You are asked to design a de power supply using a bridge full wave rectifier, as shown in Figure 1.d, to deliver a de voltage of Vo = 12 V to a 3 k2 load resistor with a ripple of less than 0.6 Vpp, where Vpp is the peak to peak voltage. The input voltage is a sine wave with frequency of 50 Hz. The diodes have a forward voltage of 0.7 V. i) Calculate the value of smoothing capacitor C. ii) Calculate the rms value of the input voltage, v(t). Figure 1.d.
Draw the input waveform and output waveform for the circuit given below with proper values marked in the figure. Assume D1 as germanium and D2 as silicon diodes. Input Vpp%3D20V, V1=3 V and V2=10 V. R D2 D1 Vin Vout V1 V2 Maximum voltage of output waveform Minimum voltage of output waveform Ps
Consider the half-wave rectifier shown below. It needs to deliver 0.1 A and an average of 15 V to a load. The source is 60 Hz and the diode has a 0.7 V drop. The allowable ripple is no more than 0.4 V (2.5%). Find: Peak AC voltage Vm of the source a) b) The minimum value of the smoothing capacitor(s) c) Comment on the type of capacitor and its/their values you would use for this amount of capacitance vs(t) K Load UL
Exercise 3 Compare between Half-wave and Full-wave in term of the following: a- Number of diodes b- Law of average voltage c- Diagram of the wave after rectifier
Consider the half-wave rectifier shown in the figure below. Let vs be a sinusoidal with 10V peak amplitude with frequency of 60Hz and let R = 1000 ohms. Use the contant voltage-drop diode model with VD = 0.7 V.