The gross allowable soil pressure is 100 kPa andwidth of the wall is 200mm. Assume that the top ofthe footing is at the ground level.B) Check the adequacy of the footing for BeamShear considering 1m strip Problem 4A footing supports a 200mm thick concrete wall.Wall loads: = 175Dead Load kN/m89%DLive LoadkN/m= 20.6%3DConcrete, f'cMPа= 415Steel, fyMPаUnit weight = 23.6of concrete kN/m3Factored= 1.2Dload+ 1.6LcombinationThickness of =footing 350mmSteel Cover (bottom offooting tocentroid of90mmbars)

Given Data: The thickness of the concrete wall is T = 200 mm. The wall load is WL=175 kN/m. The dead…

Answered: B) Check the adequacy of the footing…

Engineering

Civil Engineering

B) Check the adequacy of the footing for Beam Shear considering 1m strip

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A footing supports a 200mm thick concrete wall. Wall loads: = 175 Dead Load kN/m = 89 Live Load kN/m = 20.6 Concrete, f'c MPа = 415 Steel, fy MPа %3D Unit weight = 23.6 of concrete kN/m3 Factored :1.2D %D load + 1.6L combination Thickness %3D of footing 350mm Steel Cover ( bottom of footing to centroid of 90mm bars) The gross allowable soil pressure is 100 kPa and width of the wall is 200mm. Assume that the top of the footing is at the ground level. A) What should be the width (m) of the footing so that the allowable soil pressure will not be exceeded? (Dimensions in multiples of 50mm) B) Check the adequacy of the footing for Beam Shear considering 1m strip C) Calculate the required spacing reinforcements for diameter 16mm main bars and 10mm shrinkage and temperature bars.
H.W.1: One-Way Slab: 1. Check slab thíckness. 2.Check shear force. 3.Design flexural reinforcement for the slab. I 4.Dosign flexural roinforcement for continuous beam B. fe=28Mpa 6m 5.8m 5.8m 6m f,-420Mpa Slab h=250mm 6m Beam Section: ha600mm bw#350mm Column Section: 500x500mm 7m LL=5kN/m? Exterior D.L-4kN/m? 7m K
Design a RC square footing by Ultimate Strength ACI Column dimensions: 14''x14'' LL= 100 k DL = 71 k qall= 4 ksf f'c = 3 ksi fy = 60 ksi
roportion a trapezoidal combined footing for uniform pressure under dead load plus reduced live load with the following data in table. Distance c/c of column is 6 m and projection beyond column not exceed 0.5 m DL+Reduce dLL=175Kn/m2 DL+LL=230KN/m2 columnA DL=620KN LL=390KN column B DL=670KN LL=815KN
ASAP PLS I GIVE UPVOTE If the square footing has an 800mm edge with a 300mm thickness, and that the 200mm x 200mm column has a 1.1m height from the top of the footing up to the finished ground line are both constructed, how much gravel (in m3) should be exactly used for a class B concrete mixture for the footing and the column (up to the finished ground line level).
A BPO will be built in a reclaimed area in Cebu City. Concrete piles will be used as its foundation with details and plans as follows: 1.25m +2.15m- +2.15m→ +2.15m→ +2.15m→ +2.15m→+2.15m + 1.25m 1.25m 2.15m 2.15m 2.15m 2.15m C-1 C-2 1.25m 田田田田田田田田田田田田田田田田田田田田
A simply supported 1 way slab having span of 3 meters is to carry the load for DL = 5kpa and LL = 4.8Kpa. If the concrete f'c = 28Mpa and rebar to be used is 10mm with fy = 276Mpa. a.) Determine the minimum thickness of the 1 way slab.(answer in millimeter in whole number) b.) Determine the Ultimate loading combination for the slab considering 1 meter strip?(answer in KN/m. in 3 decimal places ) c.) Determine the Ultimate moment for the slab considering 1 meter strip?(answer in KN-m. in 3 decimal places) d.) Determine the effective depth of the slab considering concrete cover = 20mmanswer in millimeter. in whole number e.) Determine the area of reinforcement for the slab based on the actual loadings.(answer in sq.mm. in 3 decimal places) f.) Determine the spacing of the rebar.(answer in millimeter(Don't round up, use actual value). in 3 decimal places)
Square column size 16" 280 kips, PLL = 180 kips L = 1.5B, fy = 60 ksi, f'c = 4000 psi fa 4 ksf, Footing base = 4'-6" Df PDL find 26", soil weight = 100 pcf, Reinforcement - #8 bars 1) Design for load transfer 2) Development length for the dowels 3) Design bars for footing at both directions 4) Bars fit the footing based on development length 5) Two way footing spacing diagram. 4'-6" 26 B VỈ L Ildi [ld₂ Dowel Configuration B 1.5
4. A 2.10m x 2.10m footing carries concentrically a square column 0.40m x 0.40m. Design data: Column factored loads: DL = 570KN = 460KN %3D Concrete cover to the centroid of footing reinforcement = 110mm Concrete f'c - 21MPA Steel fy= 415MPA %3D %3D Allowable stresses at ultimate loads: For diagonal tension or two-way action shear = 1.52MPA For wide-beam shear 0.78MPA Maximum steel ratio for moment = 0.016 a. What is the minimum thickness (mm) of footing required for punching shear? b. Determine the minimum thickness (mm) of footing required for wide beam shear. Determine the minimum thickness (mm) of footing required for maximum moment. C.
A square column with side dimension of 70 mm rests on top of a timber footing. It is determined that the column carries an axial load of 752 kN. If the punching strength of concrete is 14.69 MPa, determine the minimum thickness (mm) of the footing. Hiiiiiii need helppp thank u so much urgenttt
(Please Answer PROBLEM 102) PROBLEM 101:A continuous strip footing is to be located concentrically under a 300 mm wall that delivers service loadsD = 360 kN/m and L= 220 kN/m to the top of the footing. The bottom of the footing will be 1.2 m below the finalground surface. The soil has a density of 20Kn/m3and allowable bearing capacity of 280 Kn/m2. Materialsstrengths are fc’ =21 MPa and fy = 276 MPa. Find:a. The required width of footing,b. The required effective and total depths, based on shear,c. The required flexural steel area.d. Give an on-scale schematic structural detail.***Use 20 mm ØPROBLEM 102:Referring to problem 101, design the footing considering the moments induce by the following loads given belowin addition to the service loads:MD = 50 Kn-m Use the following load combinations:ML = 60 Kn-m U= 1.2D + 1.6 LME = 36 Kn-M U = 1.2DL + 1.0L + 1.0Ea. The required width of footing,b. The required effective and total depths, based on shear,c. The required flexural steel area.d.…
A3 mx 3 m square spread footing is to support a 350 mm x 350 mm column carrying a dead load of 750 kN and live load of 500 kN. For concrete f'c is 21 MPa and for steel, fy is 415 MPa. Use NSCP 2001 provisions. Determine the effective depth considering punching shear. A 300 mm 350 mm 400 mm 450 mm B.