I want the second part, you have solved the first part for me The single-line diagram of a simple three-phase balanced power system with the components ratings is shown inthe figure below:500MVA13.2KVXs = 150%400MVA13.8/132KVX₁ = 10%Τ1T2:300MVA13.8/132KVX1 = 7.5%Transmission Linej75ΩT3fö600MVA132/33KVX₁ = 12%DLoadThe load at D is 400MVA at 30kV and 0.8 p.f. lagging. Choose a base of 500MVA and 33kV at the load circuit.(a) Determine the per-unit quantities and draw the per unit impedance diagram for this system.(b) Calculate the line voltage (in kV) at bus B and the complex power at the sending end of the transmission line.

Answered: Image /qna-images/answer/eef56e48-bb86-4c67-99c2-6ce696629ea6.jpg

Answered: (b) Calculate the line voltage (in kV)…

Engineering

Electrical Engineering

(b) Calculate the line voltage (in kV) at bus B and the complex power at the sending end of the transmission

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.31P: Consider two interconnected voltage sources connected by a line of impedance Z=jX, as shown in...

See similar textbooks

Related questions

Q: Given the network shown in Figure Q1, draw the s-domain equivalent circuit and then determin draw…

Q: SOLVE STEP BY STEP IN DIGITAL FORMAT XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX…

A: Introduction When the primary winding of a transformer receives an alternating current, the primary…

Q: 45) A 40hp, 440V, 4 pole dc motor has an armature wave-wound with 846 conductors and the commutator…

A: We need to find distorting ampere turns per pole and demagnetizing ampere turns per pole for given…

Q: H-W Agiven FM Signal is e(t) FM lo Cos [lont+ 8 Sin (1877-+)] Petermine 1) The Carrier frequency 2)…

A: We need to find out the modulation index , carrier frequency and deviation for given FM signal .

Q: Q6: Test the periodic and aperiodic behavior of this natural signals a) G[n]=3sin [4pi n] +7 cos [3…

A: We need to check whether the given signal is a periodic or aperiodic .

Q: 1. The resistance of the armature of a 25 hp 250 volt series motor is 0.12 ohm and the series field…

A: We need to find out the speed at given current for given motor .

Q: a) Derive the gain for the circuit shown in Fig.2 below and explain the usefulness of this device.

A: Given data, Circuit diagram is given as,

Q: For the system Given Evaluate the system Responce what is the system type? specify the system…

Q: Q1. Consider a system defined in state-space by dx (t) dt where A = Ax(t) + Bu(t) y(t)=Cx(t)+Du(t)…

Q: A short transmission line connects a step-up transformer on the source side with a series impedance…

A: It is given that: VL-L=17 kVVL-N=173 kVN1N2=114N3N4=181ZL=0.463+j0.0772 ΩX1=j0.5 ΩR1=50 ΩZc=-j0.324…

Q: For the given circuit, with R1 = 3.07 kohms, R2= 1.99 kohms and R3= 1.82 kohms, compute for the…

A: We need to find out the thevenin equivalent Voltage for the given circuit.

Q: Draw a schematic circuit diagram the oscillator circuit (with its differential output) that Raphael…

Q: Compute the DFT of the following sequence using the matrix form. x(n) = {0, 1, 2, 3} Then compute…

Q: Question 10 Refer to the figure below. e(t) = 200 sin(314t) V R = 40 02 ww VR Determine the voltage…

A: We need to find out the voltage across resistor and value of capacitor for given circuit.

Q: (d). In a dynamic random access memory (DRAM) unit cell, what is the minimum number of devices for…

A: We need to tell about DRAM ans compare with SRAM .

Q: A 3-phase 6-pulse converter is operated from a three-phase delta- connected 230 V, 50 Hz supply to…

A: Given information is written below. A 3-phase, 6-pulse converter is operated from a 3-phase…

Q: (b) A steam power station spends RM30 million per year for coal used in generation. The coal has a…

A: We need to find out the average load for given system .

Q: 2. Determine whether the following discrete-time signals are periodic or not. For the periodic ones,…

A: We need to check whether the given signal are periodic or not .

Q: Determine the voltage V, using node-voltage method. -j2 Ω 3/0° A j4 Ω m ΤΩ => 2V 2Ω

A: In this question We need to determine the voltage Vo as shown the circuit using the nodal analysis.…

Q: A wire carrying a current of 3.8 A is located inside a magnetic field of constant magnetic flux…

A: Given data, Current I = 3.8 A Flux density B=14.1 T. Angle θ=210. Length of conductor l=20 mm=…

Q: A trans-impedance amplifier (TIA) has a signal gain of -1500 V/A up to certain operation frequency.…

Q: What are the expected voltages at points C and D of this circuit? 三三三三三季 O 6 V and 0 V 12 V and 12 V…

A: Note Current in series circuit remain same but voltage change based on resistance. Voltage in the…

Q: Explain in basic terms how the wire above the ground plane acts as a transmission line? What is the…

A: A transmission line is a specific type of electrical circuit that is used to transfer electrical…

Q: Consider that you have the following state representation system, Determine the Transfer function by…

A: Given: x1˙x2˙x3˙=-5-30200010x1x2x3+200u, y=016x1x2x3

Q: Waveform Generator RED CLIP BLACK CLIP R1 C1 1kΩ 100μF GND Figure 3: Breadboard circuit. Wave I Gen…

A: Note Time constant τ of RC Circuit=RCTime constant τ of RL Circuit=LR

Q: M*SH ANALYSIS. CALCULATE THE BRANCH APP POTENTIAL DIFFERENCE ACROSS C AND D 10123 lov b IN ww 252 25…

Q: Compared with a wired system, what are the advantages of the radio system?

A: 1. When the number of devices involved in the communication system increases, to connect all the…

Q: As an assignment for antenna course work, you are asked to design a mobile phone antenna which is…

A: Design a mobile phone antenna which is suitable for a 4G LTE mobile cellular radio system, Centre…

Q: For a microprocessor similar to ATmega328p an 8 bit ADC uses a VREF= 3.3 V. When an analog read is…

A: We need to find out input voltage for given output .

Q: What is common channel signaling? And how does it work?

A: Common channel signalling It is signalling in which a group of voice and data channels share a…

Q: 1.1 Given the timing diagram for 3-bit input A and two outputs, S and C in Figure la, where A2 is…

A: Given: Timing diagram for 3 bit input A and two outputs S and C as, To do: Determine the minimum…

Q: 2. These circuit values: Vs 9.0V, Vz-6.8V, Rs= 100 2 and RL=1 KQ. Is the Zener diode operating V₁ in…

Q: Given the continuous time signal x₁ (t)=(t+1)·(u(t−2)−u(t−4)) draw the signal x₂ (t) = x₁(-t-1).

A: Since you have asked multiple questions in a single request, we will be answering only the 1st…

Q: b) For the circuit in Figure Q4b, determine; i) ii) The phasor current, I, and the phasor voltage,…

A: Note: Only active power will be available in purely R Load Only Reactive power will be available in…

Q: Q5: Use Z transformer method to design digital microprocessor starting from desecrate digital…

Q: Q2: The normalized radiation intensity of a given antenna is given by U = sin 0 cos Ø 0 ≤0 ≤π/2 Find…

Q: b) Analyse the principles of circuit theory as applied to the circuits illustrated in Figure 4b with…

A: Given circuit, Given data, Voltage V=120 V Frequency f=50 Hz Resistance R2=30 Ω Inductance L=106 H

Q: A digital signal is defined as x[n] = cos(n47/5) a. Is this sequence periodic b. Find the first 6…

A: We need to check whether the given signal is periodic and we need to find out the first 6 elements…

Q: 6. Draw the signal x[n] = e e(-0.5*n)

Q: Example 4. In the circuit show in Fig. 7, calculate the value of the unknown resistance R and the…

A: We need to find out the resistance and current for given circuit .

Q: A constru is required to lift a load of 5000 kg from ground to a height of oom in 308. The hoisting…

A: Given: The weight of the load is as follows, Lw = 5000 kg h=60 m D= 0.9 m ηm=94% ηg=98% PF = 92%

Q: Compare the quarter-wavelength monopole and half-wavelength dipole in terms of their radiation…

A: We need to compare the given antenna .

Q: 10\ The amplitude fluctuation exhibited by QPSK may be be reduced by A\bpsk b\QAM C\ MSK d\ OQPSK

A: Given: Amplitude fluctuation exhibited by QPSK may be reduced by, a) BPSK b) QAM…

Q: 2-24. Voltage and current for a device (using the passive sign convention) are Σ(0) Σ(1) Determine…

A: Given data Voltage, vt=50+∑n=1∞50ncosnπt V Current, it=10+∑n=1∞10n2cosnπt-tan-1n/2 We need to…

Q: 4-v SHOW COMPLETE SOLUTION FIND THE CURRENT in THe 8 OHM wad USING NORTON'S THEORUM - 252 an 452 62…

A: We need to find out the current for given resistor by using of norton equivalent circuit .

Q: What should be the number of revolutions of a dc machine to be able to have a generated em of 200V?…

A: Given data- DC machine- Generated emf E=200 V, Number of poles P=4, Total active conductors Z=746,…

Q: PA $ !!

A: Given data, Voltage Vst=V^ssinωt Output Voltage Vct=V^csinωt+ϕc ω=1RC

Q: Solve for IA, IB,and I of the circuit shown below using Superposition method.

Q: in Figure 2 where K is a positive gain. (a) Find the closed-loop transfer function (s)/R(s).

Q: a) Determine re b) Calculate the gain Av=Vo/Vi c) Determine Zi and Zo

A: Given: Formula used:Voltage gain =-αRc||RLre+RE α=ββ+1 Zin=RB||β+1rE+RE

Concept explainers

Star Delta Conversion

Find the input resistance between points A and B of the following resistive network:

Question

I want the second part, you have solved the first part for me

The single-line diagram of a simple three-phase balanced power system with the components ratings is shown in
the figure below:
500MVA
13.2KV
Xs = 150%
400MVA
13.8/132KV
X₁ = 10%
Τ1
T2
:
300MVA
13.8/132KV
X1 = 7.5%
Transmission Line
j75Ω
T3
fö
600MVA
132/33KV
X₁ = 12%
D
Load
The load at D is 400MVA at 30kV and 0.8 p.f. lagging. Choose a base of 500MVA and 33kV at the load circuit.
(a) Determine the per-unit quantities and draw the per unit impedance diagram for this system.
(b) Calculate the line voltage (in kV) at bus B and the complex power at the sending end of the transmission line.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Q2) A 13.2-kV single-phase generator supplies power to a load through a transmission line. The load's impedance is Ztoad 500 236.87° ohm , and the transmission line's impedance is Zine = 60 253.1° ohm. To reduce transmission line losses to 0.0103 of its losses without using the transformers design and use two transformers T1 between the generator and the transmission line and T2 between the transmission line and the load.
A parallel connection of a RL branch with a C branch is connected across a 100V AC mains. At first R = 10 ohms, L = 20mH and frequency of 1000rad / s, the current measured is 2.2361A at 89.44 leading power factor. A) Determine the initial capacitance. B) However, a fault occurs on the capacitor branch making its capacitance 20% lower and a resistance of 5 ohms is detected. If this faulty circuit is rerun but at a frequency of 500 rad / s, determine the new current that will flow through the circuit.
A synchronous generator has been synchronized to an infinite grid of 13.8 kV and 60 Hz. The generator prime mover C/C is such that the no-load frequency is 62.5 Hz and the power slope is 1 MW/Hz. The AVR C/C (The reactive power against the terminal voltage C/C) is such that the zero reactive power voltage is 14.6 kV, while the slope is 0.4 MVAR/kV. Calculate (a) the kVA loading of the generator and its power factor. (b) the settings of the prime mover and AVR such that the generator delivers 3 MW at 0.85 lagging power factor.
A 480V/240V, 60Hz single transformer has Z1 = 0.1+j0.22 ohms and Z2 = 0.035 + j0.12 ohm. Find the equivalent impedance in ohm referred to the secondary. Group of answer choices 0.07+j0.135 0.06+j0.175 0.04+j0.135 0.06+j0.135
5.5 kW, 1450 rpm. L-type equivalent circuit and parameters for a continuous sinusoidal phase of a star connected 3-phase ASM with line voltage 220 V and frequency 50 Hz are given as follows, ignoring core (iron) losses: R1=0.21 Ohm, R2=-0.18 Ohm, X1=X2-0.66 Ohm and Xm = 9.9 Ohm How many times the inrush current will be the rated current when the ASM is started directly? Answer options group 8.0815 2.6455 4.3763 7.1534 1.2558 6.3414 5.2280 3.7473
A- A 3-ph, double circuit O.H.T.L, 320 kV, 340 km, 50 Hz has a configuration as shown in the figure below where each phase in the double circuit has a double bundle with a spacing of d cm between the two conductors in the bundle where d is the last two digits (from right) of your registration number (i.e for the student that has a registration mumber 202112396, d= 96). Each conductor in the bundle has a diameter of 0.135 ft and a geometric mean radius (Ds = 1.6 cm). Calculate: 1- Inductance per phase per km. 2- Total inductive reactance. 3- This T.L. is required to supply 240 MVA at 0.86 lag P.f. at 320 kV, assuming that this load is divided equally between these two circuits, find the voltage drop across this T.L (ignore capacitive effect in the calculation). 4- What may happen if we replace the location of a' and c' bundles. Discuss your answer. 5- Suggest a way to ređuce the value of the inductance. Verify your suggestion. -8 m 3m 3m 8 m 11 m
L-type equivalent circuit and parameters for a continuous sinusoidal phase of a 5.5 kW, 1480 rpm, line voltage 220 V and frequency 50 Hz star-connected 3-phase ASM, ignoring core (iron) losses given as follows: R1=0.21 Ohm, R2=0.18 Ohm, X1=X2=0.66 Ohm and Xm=9.9 Ohm i, i, R, R, eee R, (1-s) m S How many times the rated current will the inrush current be when the ASM is started directly? O 6.3414 O 1.2558 5.2280 O 3.7473 O 7.1534 4.3763 O 2.6455 8.0815
Two power system areas operating at a nominal frequency of 60 Hz are connected with a tie line, and have the following characteristics: Area 1: R1 = 0.02 pu and D1 = 1 pu on a base of 1200 MVA Area 2: R2 = 0.03 pu and D2 = 0.8 pu on a base of 700 MVA The power flow direction on the tie line is from Area 1 to Area 2. Using a common base of 1000 MVA, what is the change in tie flow (in MW) for a load increase of 200 MW in Area 1? Select one: a.-56.16 MW O b. None of these O c.-143.84 MW O d.-38.02 MW <
6.5% ans ex A so kvA. 2o00/20 V, So He single-phase transformar has impedance drof of8% and resistance drop of 4%. Caleulate. The Requlation of the Thams former at full- Load o8 P.s Legging. also find The Power factor at which Voltage requlation will Be Zero. Sols 0.5 leading. s alculate The % Noltege Requlation af atransformar in w hich the Percantage resistance drof is 1% and Percentage dre is 6% when The Power fador is 0.8 lagging ) > unity aMS 38 % ans 1 % (シ→ 0.8 leading . amS - 2.2%
Problem 5 Consider a three winding transformer with the following particulars: = Z₁ Z2 Z3 =0.02 + j0.08 £, V₂ = 400 V, 12 = 60/30° A, and I3 = 50/-40° A. Assume that V₂ is the reference phasor, calculate: The intermediate voltage Vo. a. b. The primary current I₁ and the primary voltage V₁. c. The tertiary voltage V3 referred to the primary side. d. The apparent powers and the power factors at the primary, secondary and tertiary terminals. e. The transformer efficiency.
Q.3 Power Systems - Basics of Power Syst... A power system is represented by a single line diagram which is shown below p.u do 11 12 The Ratings of the system is as follows Generator rating = 40 MVA, 25 KV, XG = 0.2 hee Transformer T₁ Rating = 33/220 KV. What will be the p.u reactance of generator near to transformer 1 to a base of 100 MVA, 33KV?
2) The one-line diagram of a three-phase power system is as shown in Figure. Impedance are marked in per-unit on a 100-MVA, 400-kV base. The load at bus 2 is S2=15.93 MW - j33.4 Mvar, and at bus 3 is S3-77 MW + j14 Mvar. It is required to hold the voltage at bus 3 at ...L0 kV. Working in per-unit, determine the voltage at buses 2 and 1. (Please determine the voltage magnitude within the specified limits: 410-450 V. By considering the voltage magnitude value you determined yourself, solve the question.) V₁ j0.5 pu V₂ j0.4 pu S₂ Figure V3 S3