B-8-6. Consider the system shown in Figure 2. This system is subjected to three input signals: thereference input, disturbance input, and noise input. Show that the characteristic equation of this system isthe same regardless of which input signal is chosen as input.R(s)G₁(s)DisturbanceD(s)H(s)C(s)G2(s)Figure 2. Closed-loop control system.NoiseN(s)

Answered: B-8-6. Consider the system shown in…

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.2P

See similar textbooks

Similar questions

i. Draw the graph of Ramp signal and also write the equation. i. Define Peak time.
X Figure 1 High-precision CNC machine (https://www.aliexpress.com/i/32933630603.html)
Control Systems: Which type of compensation is show by the plots
What is the difference between a positive clamper and a negative clamper? Explain with the aid of circuit diagrams and output waveforms.
Explain about (ZCS) zero current switching and (ZVS) zero voltage switching in steady state transient condition: a) Switching current and voltage of the switch b) output current and voltage at the load
Explain the concept of “EXTENDED EQUAL AREA CRITERION” 2. Discuss in detail about “The Transient Energy Function Method” 3. Write about the “Factors Affecting Transient Stability”. Discuss about NUMERICAL SOLUTION OF SWING EQUATION
Topic: TOPIC: Thyristors and Phase Control Study the thyristor's IV Characteristic Curve. Then try and explain it to your younger self. Why is the maximum firing angle of the AC resistance trigger circuit limited to 90 degrees?
Compute the closed-loop poles. What effect does increasing the free pa- rameter K₂ have on the closed-loop poles, and so on the closed-loop re- sponse?
A single-phase full-wave converter in the figure below is supplied with a 120-V, 60-Hz source. The load is highly inductive and the load current is continuous and free of ripples. The electromotive force is neglected (E = 0) and the resistance has a value of R = 10 2. The average output voltage is 85% of the maximum possible average output voltage. The delay angle would be equal to: Select one: 81.8° O b. 31.8° O c 67.8° O d. 51.8° AT₁ AT, R L +7=4₂ W
Hybrid vehicle. FIGURE P1 shows the block diagram of a possible cascade control scheme for an HEV driven by a dc motor (Preitl, 2007). The block diagram of the speed control of an HEV taken from FIGURE P1, and rearranged as a unity feedback system is shown in FIGURE P2. Here the system output is C(s) = Kss V(s), the output voltage of the speed sensor/transducer. pC, Av,- Speed K, Gre(s) controller command Torque Amplifier controller output & power voltage amplifier Acro- Motive dynamie Armature Speed |drag torque Angular speed, Ref. circuit Armature torque Vehicle signal R,(s). error U(s) T(s)T,(s) current E,(s) speed, V(s) Gse(s) K, Grc(s) R. tot Friction Feedback speed signal Kss2(s) Feedback torque current signal Kes I(S) T,(s) E,(s) Back emf D=k ks Current sensor sensitivity Kcs Speed sensor sensitivity Kss FIGURE P1 Hybrid Vehicle R (s), E (s) Uc(s) |C(s) + Gsc(s) 0.11 (s + 0.6) SC s (s + 0.5173) + 5 (s + 0.6) (s + 0.01908) URE P2 Block diagram of the speed control of an HEV a.…
a. b. C. There is a dc-dc converter that provides isolation between input and output current. Identify the converter type and describe the operation. Draw the equivalent circuit to support the explanation. Assume the converter operates in continuous-current mode. Explain why a switched -mode dc-dc converter is better that a linear regulator. As an electrical engineer, you are required to design a chopper circuit with an output voltage of 10 V from a 30 V input with switching frequency of 50 kHz. The circuit is operated in continuous current, and output ripple voltage is less than 0.8% with resistance load of 30 Q. Assume the inductor value is 50 % larger than Lmin and assume ideal components for this design. Identify the chopper type and construct the circuit with IGBT as the power switching.
Environmental considerations for transducer selection includes: Select one: a. Natural Hazard, Human cause hazard, Power requirements and Loading effect b. None of the given answers C. Natural Hazard, Human cause hazard and transducer input quantity type d. Natural Hazard, Human cause hazard and transducer principle (resistive, inductive, capacitive)

SEE MORE QUESTIONS

Recommended textbooks for you

Power System Analysis and Design (MindTap Course …

Electrical Engineering

ISBN:

9781305632134

Author:

J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:

Cengage Learning