At the same depth, pressure against the bottom is greater in saltwater than in freshwater. Select one: True False
Q: Water is flowing horizontally in a pipe that has a diameter of 25cm. The water is flowing at 8 m/s. ...
A:
Q: otive power for the experimental 17.9-Mg bus comes from the energy stored in a rotating flywheel whi...
A: Bus mass=17.9Mg=17900kgFlywheel mass=1380kgRadius of gyration =560mmMax speed=3560rev/minv=60km/hr =...
Q: A car moves in a straight line such that for a short time its velocity is defined by v= (3t^2+ 2t) m...
A: v= (3t^2+ 2t) v=dx/dt, a=dv/dt dx/dt=(3t^2+ 2t) x=(3t^3/3+ 2t^2/2) x=(t^3+ t^2)+c At t=0, x=0 c=0, ...
Q: The elastic cord has an unstretched length l0 = 1.5 ft and a stiffness k = 12 lb/ft. It is attached ...
A: As per our guidelines we are supposed to solve only 3 subparts if multiple subparts are asked . Kind...
Q: ht ceing n A strel -200 Garod with a ceculer cross section k5m long Detemine the minum diameter regu...
A: The minimum diameter of the rod required is 18.80 mm or 0.0188 m.
Q: Еxample 2 During a high Reynolds number experiment, the total drag force acting on a spherical body ...
A: The friction drag coefficient of the sphere is CD,friction = 0.0115.
Q: Determine the resultant of the general force system, and find moment about x,y,z? 40KN 15cm locm 60K...
A:
Q: Give an example problem with this topic:Dynamic Equilibrium in Translation (Analysis as a Rigid Body...
A:
Q: An object will possess uniform motion as long as the resultant force acting on it begins to decrease...
A: It is required to choose correct answer
Q: Please solve and show your solution on a paper with units in every proceedure. Determine the densit...
A: Answer: The density of air is 0.0578 lbm/ft3.
Q: The weight of a metal in a satellite is observed to be 3 lbf where the local acceleration of gravity...
A:
Q: A golf ball is launched with the initial conditions shown in the figure. Determine the radius of cur...
A:
Q: The acceleration of a rocket travelling upward is given by a = (6 +0.02s) m/s², where s is Determine...
A:
Q: IN A THROTTLING VALVE, steam of P = 1000 kPa H = 1000kJ/kg flows until P becomes 100kPa. What is the...
A: Answer: ◆ The fraction of the liquid that was vaporized is 0.258. ◆ Therefore,the correct answer is ...
Q: ing each cycle, the fluid in a Stirling cycle engine accepts 2.67 kJ of energy from the combustion p...
A:
Q: A thin-walled spherical vessel, which is made of AISI C1020, as rolled steel has a diameter of 2.5 ...
A: Given Data The diameter of the rod is: d=2.5 ft=762 mm The joint efficiency is: ηj=0.80 The minimum...
Q: 1. The wheel starts rotating from rest, 4) if its angular velocity W as a function of angular positi...
A:
Q: Calculate the rpm if value of relative centrifugal field is 31,360 g and rotor radius is 7.0 cm
A: GivenRCF=31.360gr=7cm=70mm
Q: At the proportional limit, a 18 mm thick 84 mm wide bar elongates 6.9 mm under an axial load of 495 ...
A: The change in width of the bar is -0.1242 mm.
Q: Determine the force P that will give the body shown in the figure below an acceleration of 6 ft/s^2....
A:
Q: A compressor is to be driven by a 10-hp electric motor at 1750 rpm. What should be the diameter of ...
A: Given: The power of the compressor is 10 hp. The rotation speed of the motor is 1750 rpm. The mater...
Q: 2) Determine the mass of each of the two cylinders if they cause a sag of s equal to 0.85 m when sus...
A:
Q: 2. A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as s...
A:
Q: 2. Discuss the advantages and disadvantages of hydraulic control system with respect to pneumatics c...
A: Introduction: Hydralic system and pneumatic system both uses the fluid (liquid or gas) links to supp...
Q: 5. For the following pin-collected link assembly, link AO is pinned at point O, and moves with angul...
A:
Q: 1. The wheel starts rotating from rest, 2) if its angular velocity W as a function of angular positi...
A:
Q: A swimmer dives off a cliff with a running horizontal leap as shownin the figure. А. How long will i...
A: Given: h = 8.5 m x = 1.9 m
Q: Why did they chose 1.40MPA and 1.60MPA and not 1.45MPA and 1.50MPa since it is closer to 0.15436?
A: GivenT=250oCspeciic volume v=0.15436 m3/kg
Q: frictionless ring at B. Knowing that the tension in the cable is 385 N, determine the magnitude and ...
A:
Q: How many minimum turbines are required to produce 10000 kW power if: - The KE of the wind is conver...
A:
Q: A truck is traveling at 40 mph when the brakes are applied on all of its wheels, causing it to skid ...
A: Given: The initial velocity of the truck is 40 mph. The skidding distance is 33 feet. The weight of ...
Q: A container having pressurized gas in its upper part and water in its lower part. Pressure of the ga...
A: GivenP1=4MPam=1kgm=1kgV2=n×103Pa=1MPag=10
Q: 1. The wheel starts rotating from rest, 3) if its angular velocity W as a function of angular positi...
A: Given: r= 0.3m ω=0.3θ3 rad/s
Q: As a train accelerates uniformly it passes successive kilometer marks while traveling at velocities ...
A:
Q: A catapult is used to throw large projectiles by the ancient civilization. If a catapult swung from ...
A: Find the force on projectile.
Q: Q1) What does it mean when we say composites are notch sensitive? Q2) What are the differences betwe...
A: The given questions deal with material science. (NOTE: According to Bartleby's Answering G...
Q: a) Compute the bearing of line BC. b) Compute the distance of line DE. C) Compute the area of the lo...
A: Given data
Q: Determine the number of degrees of freedom for the following mechanisms:
A: given; find degree of freedom=?
Q: File Help x, Intro Torque Moment of Inertia Angular Momentum PHET Applied Force 2Fapplied=4 N Forake...
A: Given: Fapplied = 4N Fbrake = -3N r = 4m
Q: The thickness of the blank
A: Given; Determine thickness of the blank needed to produce; by power spinning a missile cone of thick...
Q: Q2/Calculate the magnitude of the tension T and the angle 0 for which the eye bolt will be under a r...
A:
Q: A dormitory at a large university, built 50 years ago, has exterior walls constructed of L, = 25-mm-...
A: Answer: (a) The heat flux through the original walls is 75.51 W/m2. (b) The heat flux through the re...
Q: Determine the following based on the diagram below Magnitude of the maximum shear force • Location o...
A:
Q: In each case, calculate the support reactions forces and then draw the free-body diagrams of joints ...
A: Consider the free body diagram for the system.
Q: Calculate the forces in members BC, BE, and EF. Solve for each force from an equilibrium equation wh...
A: Given that, the load is 8.9 kN and length of the members AG and BF are 4 m. Let's mark the point H a...
Q: Prove the following derivation
A:
Q: 9. Calculate the increase in stress for each segment of the compound bar shown. If the temperature i...
A:
Q: A single-threaded power screw is 25 mm in diameter with a pitch of 5 mm. A vertical load on the scre...
A:
Q: 2. Solve for the following pitch angles if the gears has zl = 12, z2 = 14 and E = 110° Fill up the f...
A: Solution: Given Data: z1=12z2=14∑=110o Note: Since, you have asked to solve 9-11 sub-parts, those ...
Q: An inventor claims to have a machine that outputs 34hp. The machine uses a 20 kg/min flow rate of li...
A: Decesion is based on the entropy generation . For canot cycle it should be zero First assume cycle ...
At the same depth, pressure against the bottom is greater in saltwater than in freshwater.
True
False
Step by step
Solved in 2 steps
- 1. A tube contains an oil of specific gravity 0.9 to a depth of 120 cm. Find the gauge pressure at this depth in psi. Given: Required(aim): Formula: Unit analysis: Answer: Note: pls follow the format( need asap) thanks.a drum has gasoline s.g=0.9, with oil s.g=0.8 and sea water s.g=1.03. the depth of the liquid is 0.8m, 0.5m, and 1.0 for gasoline, oil and sea water.1. find absolute pressure at depth 1.2m 2.find the depth at 1.8m 3. find the force F at depth 2.1m when diameter of drum is 0.5m1. Given an air with a known temperature and pressure of 4 degree Celsius and 105 KPa, respectively, find the density of the air. 2. A rigid container is closed at one end and measures 7 inches diameter by 14 inches long. The container is held vertically and is slowly moved downward until the pressure in the container is 16.5 psia. What will be the depth of the water surface measure from the free water surface?
- Consider the sealed containers (same fluid and on the same ground level) below with heights given in ? and ? values.Provided that ? = 2?, answer the following items. (refer to a.jpg) What container has the greatest pressure at the point indicated? Which point experiences the least pressure? Suppose the bottom pressure is evaluated, what container experiences the second highest pressure?A tank open to the atmosphere contains oil of sp. gr. = 0.80, gasoline sp.gr. =0.90 and seawater sp.gr. = 1.03. If the depths of the liquids are 0.65 m., 0.92 m., and 1.15 m. for oil, gasoline and sea water respectively. Find the absolute pressure at a depth of 2 m.1. A tube contains an oil of specific gravity 0.9 to a depth of 120 cm. Find the gauge pressure at this depth in psi. 2. Determine the vertical pressure in kgf/cm² due to a column of water 70 m high.
- A concrete block is attached to the gate as shown. If the water level is 1.3 m from the bottom of the container, there is no reaction force at A.What would be the reaction force for the level shown?Note 1: Specific gravity of concrete is 2.4.Please show clear workings with explanations to steps taken. I don't just want the answer, I want to understand the process to answering this question. ThanksAn open tank contains oil and water. Oil, having a specific gravity of 0.80 forms a 1.90 m deep layer in the tank with a total depth of 5 m. What is the gage pressure at the bottom of the tank?A container, closed on the left and in the middle but open to atmosphere on the right, is almost completely filled with water, as shown below. The points a-g are marked in the container. Rank the points from lowest pressure to highest pressure. Note that points b, cand fare at the surface. C d b e
- An open tank contains water up to a depth of 1.2m from the bottom and above it mercury for a depth of 0.8m and above it an oil of specific gravity 0.8 for a depth of 1m. Assume the atmospheric pressure is 1 bar. Find the gauge pressure and absolute pressure i) at the bottom of the container, ii) at the interface of water and mercury and iii) at the interface of an oil and mercury. ( i) At bottom Gauge Pressure = ________________N/m2 Absolute Pressure =_________________ N/m2 ii) At the interface of water and mercury Gauge Pressure =_______________ N/m2 Absolute pressure =_____________ N/m2 iii) At the interface of oil and mercury Gauge Pressure =_____________ N/m2 Absolute Pressure = _________________ N/m2ASAP pls dont round off initial values, round off final ans only ty An open tank contains 3.86 m of oil (sp.g=0.8) and 5.41 m of water. Find the pressure at the midpoint level of water.Discuss the variations of hydrostatic force with depth of immersion.