As shown in the figure below, a Venturi meter is installed on a 300-mm diameter pipe whose maximum flow is 125 liters per second and the pressure head is 6.5 m of water. Determine the minimum throat diameter that will give a negative head. Solve for the discharge that will pass through the meter when the double column differential mercury gauge connected to it will show a difference of 25 cm. 25cm 6.5 h A2 300mmø A1 ANSWER: a. D = 118mm b. Q = 87 liters/sec

As shown in the figure below, a Venturi meter is installed on a 300-mm diameter pipe whose maximum flow is 125 liters per second and the pressure head is 6.5 m of water. Determine the minimum throat diameter that will give a negative head. Solve for the discharge that will pass through the meter when the double column differential mercury gauge connected to it will show a difference of 25 cm. 25cm 6.5 h A2 300mmø A1 ANSWER: a. D = 118mm b. Q = 87 liters/sec

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

In the figure, for a pressure at A of 25kPa and with losses at A which is 5 times V₁²/2g and the loss at nozzle of 0.05 times the V2²/2g, determine the discharge and head H. Ans: 0.0136m³/s & 2.731m A 150mm dia Wit 50mm dia
M MEQ2.jpg 200mmø 690mm 300 mm 400 mmø Z Hg (13.6) A 200mm diameter venturi meter is installed in a 400mm diameter vertical main pipe as shown. If the deflection of mercury (SG = 13.6) at the manometer reads 300mm and the vertical distance between point 1 and point 2 is 690mm, determine the discharge in the system assuming a head loss of 600mm. Hide answer choices a A) 307.36 L/s B) 279.84 L/s No Answer among the choices D) 224.67 L/s 256.29 L/s O O O O C
A Venturi meter having a throat diameter of 150mm is installed in a 300mm diameter horizontal pipeline carrying oil (S = 0.80). A mercury U-tube connected as shown shows a difference in height of mercury columns of 200mm, the remainder of the tube being filled with oil. If the meter coefficient is 0.95, determine the following: a.)The theoretical discharge (m3/s). Consider HL = 0. b.)The actual discharge (m3/s). Consider HL c.)The head loss (m) between the inlet and the throat.
Glycerin of SG 1.26 flows through the nozzle shown and deflects the mercury in the U-tube gage. What is the pressure at B in kPa? A 2.75 h B Hg(13.6)
3. A 30m long, 20mm diameter steel pipe is used to drain an oil tank determine the discharge 3E when the oil level in the tank is 4m above the exit of the pipe. Neglect minor losses, (assume f = 0.12) 4m D-20 mm, L-30 m, t 0.12
Q2) Calculate The head loss due to friction in The Piping system shown below. The pipe is (15o mm) in diameter and C1som) Long, Passes aflow of Co.13 m/s 15omm 30m 2. 18m
1.) For the water shooting out of the pipe and nozzle under the condition showed, find the height above the nozzle to which the water jet will "shoot". Assume negligible head loss. Water 1.100m 1 ORECA DE Nozzle D-100 mm Point A D-200 mm Pa- 55.0 hPa
A venturi meter with 150 mm diameter at inlet and 100 mm at throat is laid with its axis horizontal and is used for measuring the flow of oil of sp. gr. 0.9. The oil mercury differential manometer shows a gauge difference of 200 mm. Calculate the discharge in liters/s. Assume the co-efficient of meter as 0.98. a. 56.4 b. 25.7 c. 27.8 d. 63.93
A venturi meter with a throat diameter of 100 mm is fitted in the inclined pipeline of 200 mm diameter with oil of specific gravity 0.88 flowing upwards. The venturi meter coefficient is 0.96. Two pressure gauges are fitted at tapping points, one at the throat reads the vacuum pressure of 40 cm of mercury and the other in the inlet pipe 320 mm below the throat is 20.231 N/cm2. If the loss of head in the main and throat is 0.35 times the kinetic head of the pipe, determine2.1 the volume flow rate of oil through the pipe2.2 the difference in level in the two limbs of the mercury manometer if it is connected to the tapping points and connecting pipes are filled with the same oil
200mmø 690mm 300 mm 400 mmø 金Ho0 Z Hg (13.6) A 200mm diameter venturi meter is installed in a 400mm diameter vertical main pipe as shown. If the deflection of mercury (SG = 13.6) at the manometer reads 300mm and the vertical distance between point 1 and point 2 is 690mm, determine the discharge in the system assuming a head loss of 600mm.
- Dekrmine the total head loss hf. from Å to o in the systen shomwn in the figure iF the discharge is 1. G0 mls. Assume f=0:02 for all pipes 450 mm o, GO0 m 9oomm ở , 90 m 구5Dmmd,40m D GUD mm,720m
In the simple hydraulic circuit shown in Figure 1 below, why is the counterbalancing pressure valve required? Sol A Sol B Ci u s 1