As shown in figure 3., water flows through pipe A 1.5 m in diameter at 2.5 m/s and passes through pipe B 1 m in diameter. The water then flows through pipes C and D, if pipe C has a diameter of 70 cm and must have a flow rate of 2.7612 m²/s, and the velocity at pipe D must be 8.4375 m/s, calculate (a.) the flow rate at pipe A, (b.)velocity at pipe B, (c.) velocity at pipe C, (d.) the flow rate at pipe D and (e.) the diameter of pipe D. V1 V2

As shown in figure 3., water flows through pipe A 1.5 m in diameter at 2.5 m/s and passes through pipe B 1 m in diameter. The water then flows through pipes C and D, if pipe C has a diameter of 70 cm and must have a flow rate of 2.7612 m²/s, and the velocity at pipe D must be 8.4375 m/s, calculate (a.) the flow rate at pipe A, (b.)velocity at pipe B, (c.) velocity at pipe C, (d.) the flow rate at pipe D and (e.) the diameter of pipe D. V1 V2

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q.1.17 MASS FLOW AT A PIPE JUNCTION Consiuer the steady flow in a water pipe joint shown in the diagram. The areas are: A,= 0.2 m. A =02 m, and A, =0.15 m. In addition, fluid is lost out of a hole at a. estimated at a rate of 0.1 ms. The avcrage speeds at sections O and are V =5 mis and V3 = 12 m's, respectively. Find the velocity at section O Given: Steady flow of water through the device. A, = 0.2 m A; = 02m A, = 0.15m Vị = 5m/s V = 12m/s p=999kg m Volume flow rate at9=01 m's Find: Velocity at section
b. Three reservoirs A, B and are connected by a pipe system as show in the following figure. The length and diameter of pipe 1,2 and 3 are 2000m, 1000m, 500m and 30cm, 20cm respectively. Find the discharge into or from the reservoir B and C if the rate of flow from reservoir A is 50 lit/s. Find the height of water level in the reservoir C. Take coefficient of friction = 0.005 for all three pipes. 140m 138 m A 1 B 2 3.
Consider the figure shown. The discharge of reservoir a is 400 li/sec. Solve for the length of pipe 2 if the flow rate of pipe 1 is 240 li/sec and the elevation of point D. El. 50m A El. 40m B L1=1200m D1=650mm fi =0.02 L3=4700m D3 =350mm f3 =0.022 Node L2= ? D2=600mm f2 =0.02 L4=4600m D4=500mm f4 =0.019 El. C Answer: Length of pipe 2 = 1809.262m, Elevation of D = 15.46m
Three pipes 1,2 and 3 connect three reservoirs A, B and C, respectively, and meet at junction D. The elevation of A is 300 m while that of C is 277m. The rate of flow out of the reservoir B is 560Lit/sec. Pipe Length (m) Diameter (mm) Friction Factor 1 1200 800 0.0175 2 800 450 0.0208 3 1800 500 0.0183 Which of the following nearly gives the rate of flow in pipe 1? a. 45.91 L/s b. 122 L/s c. 459.78 L/s d. 514.09 L/s Which of the following nearly gives the rate of flow in pipe 3? a. 100.22 L/s b. 45.91 L/s c. 459.78 L/s d. 514.09 L/s Which of the following nearly gives the elevation of reservoir B? a. 360.55 m b. 336.67 m c. 323.37 m d. 3.90 m
Determine the flow in each pipe in the reservoir shown below. Use the values provided in the table. Elevation Reservoir A 80m в 50m 20m Pipe Diameter Length friction factor AP 400mm 1800m 0.027 BP 500mm 2000m 0.02 СР 700mm 3500m 0.025 El. A El. El.
Situation 1: Give the discharge/flow rate in (m/s) of the system with a constant velocity of 2.5m/s given the following diameters. 1. 2. d= 1.5 m. d= 150 mm.
SITUATION 1: The total head lost from points A to E in the figure shown is 15m. Assume f = 0.02 for all pipes with the following given pipe data: A B Pipe Length, L (m) Diameter, D (mm) 1 450 600 2 600 500 3 360 450 4 480 450 540 600 1. Determine the flow on pipe 1 in m/s. 2. Determine the flow on pipe 2 in m/s. 3. Determine the flow on pipe 3 in m/s.
Problem 1. A water reservoir with dimensions of 10 x 10 × 10 m is connected to 3 pipes. Water is entering the tank at velocity u1 = 0.1 m/s through the inlet pipe, which has a cross-sectional area A1 0.5 m?. The bottom outlet pipe has a mass discharge rate of 30 kg/s. Given that currently the water surface is 3 m below the top outlet pipe, and the outlet pipe has a cross-sectional area A3 0.1 m²: 1. Determine the rate of mass increase in the reservoir. 2. How long will it take before the water surface reach the bottom surface of the top outlet pipe? 3. What would be the water velocity in the top outlet pipe? -A, 3m V, A, -M2 Figure 1: A water reservoir is connected to 3 pipes.
N.S/m?) Q.4. Three pipes having lengths 1000 m, 800 m, 1200 m and dia. 250 mm, 200mm and 300 mm, Hazen- Williams coefficient (C) 120, 100, 140 respectively are connected in parallel between two points, A and B. When total discharge of 0.3 m³/s flows through the system, calculate the discharge in each pipe and head loss between A and B. Pipe 1 Q=0.3 m³/sec Pipe 2 Pipe 3 IGD The rapid mixing tank will have a
What is the flow rate through the smooth pipe of 5 mm-diameter shown in figure? Assume a laminar flow. (H=2 m, L=40 m, ν=1×10-6 m2/s)
2. Compute the rate of flow in a pipe with diameter300 mm for a length of 900 meter having a head loss of 6.119 meters, if f=0.02 (Hint: Use h=(0.0826fL(Q^2))/(D^5)
Three reservoirs A, B and C are connected by a pipe system as shown in the following figure. The length and diameter of pipe 1, 2 and 3 are 2000m, 1000m, 500m and 30cm, 25cm, 20cm respectively. Find the discharge into or from the reservoir B and C if the rate of flow from reservoir A is 50 lit/s. Find the height of water level in the reservoir C. Take coefficient of friction = 0.005 for all three pipes.