As an Electronic Engineer in XYZ Analog IC Design Centre, you are required to design Operational Amplifiers (Op-Amp). Based on combination of ideal Op-Amp as illustrated in Figure Q3 (b), derive the output voltages Vo1, Vo2, V03, and V04. If V₁ = 4 V and V2 = 2 V, determine V04. R Vio-W V₂0- 2R Voi R www R R www R 3R R www V03 V02 Figure Q3 (b) 2R www 4R 2R R V04

As an Electronic Engineer in XYZ Analog IC Design Centre, you are required to design Operational Amplifiers (Op-Amp). Based on combination of ideal Op-Amp as illustrated in Figure Q3 (b), derive the output voltages Vo1, Vo2, V03, and V04. If V₁ = 4 V and V2 = 2 V, determine V04. R Vio-W V₂0- 2R Voi R www R R www R 3R R www V03 V02 Figure Q3 (b) 2R www 4R 2R R V04

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1- Mention any two advantages of Integrated Circuit . 2- For the circuit given below : Vin is a sine wave Vinpp=6 V and Vref=-2.4 V , Assume Vsat=±12V Name the circuit and draw the input and output waveforms . Vin Vref 3- Explain why open-loop op-amp configurations are not used in linear applications? Draw the block diagram of opamp and define the function of each block
Op amp and diodes are ideal. Derive Vout and sketch the transfer function of Vin vs Vout. Please show complete solution.
Ex) A standard two-junction thermocouple configuration is being used to measure the temperature in a wind tunnel. The reference junction is held at a constant temperature of 10 °C. We have only a thermocouple table referenced to 0 °C. Determine the output voltage when the measuring junction is exposed to an air temperature of 100 °C.
Op amp and diodes are ideal. Derive Vout and sketch the transfer curve of Vin vs Vout. Please show complete solution.
Draw the circuit diagram of DC to DC converter using switched capacitor.
Submit a brief report on 3 different Analog and Digital applications ofop-amp and represent a circuit design in details.(Maximum 3 page)
Determine the type of opamp circuit, the gain and the output voltage of the circuit for each of the operational amp circuits below
Q3. Design a DC/DC buck converter (as shown in Figure Q3) for an input voltage of 12V and an output of 5V at 20A. Assume a switching frequency of 10kHz. Constrain the inductor ripple current to be 10% of the input current and limit the output voltage ripple to 50mVp-p. a) Explain the working mechanism of the converter by sketching equivalent circuit diagrams when the switch Q is ON and OFF, Calculate the duty cycle of the switch. Find the ripple of the inductor current. Calculate the required inductance and capacitance. Sketch the waveform of the output voltage. Is the converter works at continuous conduction mode CCM? If so, give proof of that b) c) d) e) f) g) If the load current varies between 0 and 2A, what is the value of the duty cycle range and at what operating condition? DA L C² Figure Q3 DC/DC buck converter. R
Calculate the total offset voltage for the circuit shown below for op-amp specification values of input offset values, VIO=2.8 mV and IIO=110 nA with RF=14000 ohm and Rin= 3000 ohm.
3) Consider the Zener-diode voltage regulator shown below. Suppose you design this circuit to drive (supply) a load resistance RL. The supply voltages to the op-amp are +15 V and -15 V (not shown). a) What is Vout? b) If R = 1 k 2, what is the smallest R, that the circuit can handle without "sagging" the output voltage? c) What should be the power rating of the resistor R? Be explicit about your assumptions. +15 V R Vout IN4738 CS Scanned with CaScanner
In circuit analysis, expound separately the meaning of getting negative values for the current & voltages, in theoretical calculations or experimental data? Relate to Kirchoff Rules
A differential op-amp circuit as shown below is used to implement a given linear voltage measuring functionV = f(V,). ouf Provide answers to questions 19 – 22. ww V. V; W R out R2 Ground