please answer all Art is diving 15 feet below the sea while Aaron is swimming in the 8 feet levelof the sea.The density of sea water is 1.03 x 10^3 kg/m^3. Compare the hydrostaticpressure experience bythe 2 boys. GRESFA1 PhM-hydrostatic pressure experienced by Art31. What is 15 feet in meters? 4.5 M32. What is the pressure of the sea water at that level? 4.63X10^433. What is the equation to determine the hydrostatic pressure? PA+PDG34. What is the atmospheric pressure? 1X10^535. What is the hydrostatic pressure experienced by Art? 1.46x10^5

Given Data:Density =ρ=1.03×103kg/m3g=9.80ArtH=15ftAaronH= 8ft

Answered: Art is diving 15 feet below the sea…

Art is diving 15 feet below the sea while Aaron is swimming in the 8 feet leve of the sea. The density of sea water is 1.03 x 10^3 kg/m^3. Compare the hydrostatic pressure experience by the 2 boys.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Determine the reactions at the supports and the forces in the members of the truss shown with the…

Q: The figure below shows an inflow and an outflow hydrograph that was calculating using the Muskingum…

A: in this question a inflow and outflow hydrograph is given and we are asked to find peak attenuation

Q: MAKE A CONLCUSION ABOUT THE EXPIREMENT SPECIFIC GRAVITY OF COARSE AGGREGATES AND ABSORPTION

Q: 400 N/mm 45° B. 400 N/mm The square element in the figure is subjected to a biaxial stress of 400…

A: Given data : The value of normal stress in X direction σX=400 N/mm2 The value of normal stress in Y…

Q: Two parallel BG track have a cross-over. The crossing number of both the tracks is 12. The two…

Q: Q2/ In field work, vertical angles was measured from station A to stations B.C, as show in table…

A: Elevation : The elevation of a point is its vertical distance above or below the surface of a…

Q: 13.1 Figure 13.9 shows a retaining wall that is restrained from yielding. Determine the magnitude of…

A: A retaining wall is given as shown in the figure above, that is restrained from yielding. It has…

Q: *2-40. Determine the reactions at the supports A and D. Assume A is fixed and B, C and D are pins.…

A: Given :

Q: In Figure Q6, a simply supported 3.50 m long beam (L) has a concentrated point load (F) of 150 kN…

Q: Explain what is meant by isotropic compression and by one-dimension compression. Sketch diagrams…

Q: Determine the smallest force P subjected at the wedge B that is required to lift the B Newton crate…

A: Given, B=465 N μ=22÷100=0.22 H=12 We need to find out P.

Q: The Azimuth from North of the forward and backward tangents of a 4°. curve is 260° and 280°,…

Q: Determine the governing (LRFD) negative bending-moment (kN-m) for a beam in a university building…

A: Answer We are given Negative Bending Moment due to 1) Dead Load (D)= -340 Kn-m 2) Live Load…

Q: Determine degree of static indeterminacy

A: Degree of static indeterminacy in zero. That means structure (truss) is determimate.

Q: Determine the governing (ASD) negative bending moment (kN-m) for a column in a multistory office…

Q: Question 3 Your EIA project involves excavation of an area before the construction. Describe the…

A: Mitigation measures during the construction phase Site clearing Water quality Air quality Noise

Q: DO 4 AND 5

A: There are different types of parameters used in traffic estimations. These parameters helps to…

Q: 4. An object in isometric view is given as in Figure 3. Draw the object in Third Angle Projection at…

A: An isometric view is given. We need to draw top view, front view and side view

Q: F3-8. Determine the force in members HG, HC, and BC and state whether they are in tension or…

Q: Find the value of kinetic energy stored in ball of mass 2.5 kg moving with velocity 2.1 m/s

A: Introduction : The given question is related with mechanics . In this question we are provided with…

Q: Design inlet system for the road in figure below with catchment area shown in figure, c=0.8, i=100…

Q: A horizontal force F shown in the figure is exerted on a vertical lever ta prevent a load (weight W)…

Q: A sımply supported beam carries a load as shown in the figure below. What is the value of deflection…

Q: Find the allowable capacity of the belled caisson shown. The diameter of the bottom of the bell is 4…

Q: You have three 24 ft long wooden 2-6's and you want to nail them together in two possible…

A: ASKED: To choose the correct statement corresponding to the beam stiffness of the two arrangements.…

Q: 1. The following are disadvantages of concrete except a) tensile strength b) forms c) suitability…

A: 1. Concrete has very low tensile strength and it requires formwork to cast. Both are disadvantages…

Q: n3: An open vessel of water accelerates up a 30 plane at 2 m/s? Determine the hori zontal component…

A: ASKED: To determine- horizontal component of the acceleration vertical component of the…

Q: Question 1 A 150 x 75 x 12 angle shown in Figure 1 is connected to a gusset plate with one leg by…

Q: 1. The beam shown below is to be subjected to carry a 24 kN/m dead load, 27 kN/m live load and a…

Q: 823.) An equilateral triongle has its base b homzontal, Shaw that the centroidal moment of inertia…

Q: 2. A water tank is fitted with a drain and outlet pipe as shown in the figure. The system has 82…

A: To find out the flow rate through pipe.

Q: The T-shaped column shown is reinforced with 4-28 mm diameter bar with fy = 414 MPa. Determine the…

A: Answer We are given As = 4-28 mm dia bars As = 4*π4*282 As = 2463 mm2 f'c = 27.6 Mpa fy = 414 Mpa…

Q: Calculate the individual quantity of cement, sand, gravel, and water for the concrete pedestal shown…

Q: he steel shaft is formed by attaching a hollow shaft to a solid shaft. Determine the maximum torque…

A: Determine the maximum torque T (in Nm) that can be applied to the ends of the shaft

Q: 10.4 A beam of the cross section shown is made of a steel which is opumed to be elastoplastic with E…

Q: 5 set of sieves are to be used for analysis of aggregates. After sieve shaking the sieves, the mass…

Q: Determine the tonnage of material to be blasted in a particular bench having the following data::…

A: ASKED: To determine the tonnage of the material to be blasted. Given, Bench height = 12 m Tonnage…

Q: Determine the force in each members in CD and GF. 2 kN 1.5 m 0.8 m B A 1.5 kN 2 m -2 m

Q: Q2/ In field work, vertical angles was measured from station A to stations B.C, as show in table…

A: Given:- The height of the instrument at point A = 1.3 m The elevation at point A = 25 m The…

Q: |1m 1.5 m -5 m -5 m - 2 m

Q: Find the value of roller support reaction

A: Given data : The value uniformly distributed load w=30 KN/m The value of uniformly varying load q=0…

Q: catchment of area For a sform C/2)em 2」魚は)he。 was as fallows : Time 2 3 30 40 5 Rain fell Cmai) 22…

Q: From the beam shown below, determine the maximum deflection and maximum slope of the beam. Use…

Q: Determine the crack width of the following given beams: Take Bh=1.20,fy=414MPa and fc'=28 MPa

Q: The 8-hour precipitation measurement is given below. fo=7 mm, f=2.25 mm. Answer the following…

A: Theory: Horton's equation is given by ft = fc + (fo - fc ) e-kt fc = constant infiltration…

Q: 1. A pipeline is conveying 0.05 m3 /s of water, at 30°C. The length of the line is 300 m, and the…

A: Head Loss: The total reduction of the head in a moving fluid of a pipeline is called head loss. When…

Q: Q3 (a) Describe briefly the main objective water quality and state the main parameters involved in…

Q: F a B A

Q: Why did we compute the time to complete 95% primary consolidation settlement instead of the time to…

Q: For a grit chamber, if the recommended velocity of flow is 0.2 m/s and the detention time is 2…

A: Grit chambers are long broad tanks that are designed to slow down the flow so that solids such as…

Question

please answer all

Art is diving 15 feet below the sea while Aaron is swimming in the 8 feet level
of the sea.
The density of sea water is 1.03 x 10^3 kg/m^3. Compare the hydrostatic
pressure experience by
the 2 boys.

GRESFA1 PhM-hydrostatic pressure experienced by Art
31. What is 15 feet in meters? 4.5 M
32. What is the pressure of the sea water at that level? 4.63X10^4
33. What is the equation to determine the hydrostatic pressure? PA+PDG
34. What is the atmospheric pressure? 1X10^5
35. What is the hydrostatic pressure experienced by Art? 1.46x10^5

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Interior finishes for wood light frame construction

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

1. Water at 68 degree farenheight has a dynamic viscosity of 1 centipoise. Compute its dynamic viscosity and kinematic viscosity in foot pound-second units.
Taking the coefficient of compressibility of water to be 7 x 1O5 psia, determine the pressure increase required to reduce the volume of water by 2.5 percent. The pressure increase required is 17.5 x 10' psia.
A 82.5g of iron shot is added to graduated cylinder containing 45.5cm'of water. The water rises to the 49.1cm2, calculate the density of iron? 49.10 cm3 45.50 cm3 O 7.9 kg/cm^3 all answers are correct. 7.9 g/cm^3 32 kg/cm^3 O all answers are incorrect. O 7.9 ml/cm^3 22.9 g/cm^3
A 2-foot diameter pipe carries stormwater discharge from a site. The concrete pipe was designed with a slope of 0.8 foot per 90 feet. At the time of measurement, the pipe has 0.8 feet of discharge flowing in it. What is the pipe discharge? (Express your answer in liter per second).
Determine the friction factor for water flowing at a rate of 1 cfs in a cast iron pipe 2 inches in diameter at 80°F. [Kinematic viscosity, v, of water at 80°F = iron = 8.0*10 ft.] 0.93x10 ft/s; Roughness of cast
What height of mercury column is equivalent to a pressure of 74 psig? The density of mercury is 498 Ibm/ft3. a. 11.28 ft O b. 21.40 ft c. 16.77 ft O d. 10.70 ft
Your company has been asked you to design a storage tank for liquid petroleum gas. The customer's specifications call for a cylindrical tank with hemispherical ends, and the tank is to hold (8000 m) of gas. The customer also wants to use the smallest amount of material possible in constructing the tank. By depending on Lagrange method, what radius (r) and height (h) do you recommend for the cylindrical portion of the tank? (Nate : For hemispherical, volume & surface area = 2nr?)
Exam Q1:- Consider a large cubic ice block of (1 m) surface area floating in seawater. The specific gravity of ice is 0.92. If a (15 cm) high portion of the ice block extends above the surface of the water, determine the height of the ice block below the water surface, h? 15 cm Sea Water Ice Block
Conservation of Mass and Energy 1. What is the Reynold's number for water flowing in a 24-inch circular pipe at a velocity of 6.21 ft/s? Is the flow laminar or turbulent? What is the velocity head? 2. Water in a pipe has a pressure of 22.1 lb/ft2. What is the pressure head?.
A block of wood w/ a horizontal square section 12 in x 12 in has a depth of 9 inches. If it is allowed to float on a body of liquid which consists of 7 inches layer of water above a 10 inches layer of mercury (sp.gr.= 13.6). If the specific weight of the block is 124 psf determine the distance the bottom of the block will come to rest below inte face. Use the most the mercury nearest value.
Water flow through a 100 mm diameter pipe with a velocity of 0.015 m/sec. If the kinematic viscosity of water is 0.13 * 10^-6 * m^2/sec. Determine the friction factor of pipe material?
Give me answer according to the question A vat holding paint (s=0.8) is 8m long and 4m deep. Calculate the resultant force acting on the cross-section of the vat, draw the pressure distribution on that surface of the vat, and label it accordingly?