Arithmetic Store Load Branch Total 17 17 6 25 Assume that Arithmetic instruction takes 1 cycle, Store and Load instructions take 3 cycles each, and Branch instruction takes 2 cycles. Calculate the average CP

Q: Execute the following instruction using zero address instruction. X=X*Y+Z/A-B*C+E*F *

A: The execution of the following Instruction using zero address instruction X=X*Y+Z/A-B*C+E*F  is…

Q: Given R= 20, PC = 12 and index register X = 15, show the value of the accumulator for the following…

A: The Answer is

Q: Execute the following instruction using one-address instruction format. R=(X+Y*Z)/(A-B*C+G*D)

A: Let's understand step by step :   One address instruction format : In one address instruction format…

Q: Assume that each instruction starts from these values: AL=A3H, AH=0H, BL=12H AL is negatively…

A: MUL BL  MUL BL will multiply the contents in BL to AX and will store the result in AX. And AX = AHAL…

Q: 1) Write an instruction sequence to decrement the contents of data memory locations 0x10, 0x1 1, and…

A: As per our policy, "Since you have asked multiple questions, we will solve the first question for…

Q: Find the machine code for the instruction: SUB.B #15, W10 Machine code in HEX is: 0x v v What would…

A: Here SUB is mnemonic which stands for the subtraction of the contents of R from the accumulator.…

Q: Assume DS=3568H, CS=2322H, SS=8216H, BP=2518H and DI=E23CH. Calculate the offset address of the…

A: Actually, DS-Data Segment CS- Code Segment SS- Stack Segment BP- Base Pointer DI- Destination Index…

Q: 1. Given R= 20, PC = 12 and index register X = 15, show the value of the accumulator for the…

A:

Q: iv) Using the following instruction format, a total of registers can be addressed 8 7 10 OP code…

A: 4) 4.10

Q: MOV CS, AX. Identify the instruction wrong or correct. If it’s wrong, then correct the instruction…

A: MOV CS.AX is the wrong instruction. Here CS is a segment register(Code Segment). Segment register…

Q: MOV BX, 649Bh ВХ, ЗАҺ OR The value for BX after OR instruction executes is 65BBH.

A: Summary: - Hence we discussed all the point

Q: Q2:- Home Work: Execute the following instruction using all previous instruction format types: 1- S…

A: Here given data is 1-S=F-(C*B)+M after then we need to create a postfix expression for this question…

Q: Q1) If BX=1000, DS=0200, SS=0100, CS=0300 and AL=EDH, for the following instruction: MOV [BX] +…

A: Given, BX =1000 DS =0200 SS =0100 CS =0300 AL =EDH   Instruction = MOV [BX]+1234H,AL Physical…

Q: Write the machine code (binary code) for the following instructions and identify the instruction…

A: Binary representation in 32 bit format is : 000000 10001 10010 01000 00000 100000 Registers format…

Q: define the following: Clock rate Instruction set Bandwidth

A: 1- defined the Clock rate,Instruction set and Bandwidth

Q: Assume AL=35h; CL=05. Write the content of AL after RCR AL, CL - showing the calculation steps.…

A: Dear Student, RCR instruction in 8086 assembly language is used to perform rotations of all the bits…

Q: Write an instruction sequence to subtract the 4-byte number stored in memory locations 0x10-0x13…

A: Write an instruction sequence to subtract the 4-byte number stored in memory locations 0x10-0x13…

Q: Register BC contain 2793H and register DE contain 3182H. Write instruction to add these two 16 bit…

A: MOV AL,BCMOV BL,DEADD AL,BL    //sum will be saved in ALDAA   //Decimal adjust ALMOV [2050],ALMOV…

Q: Consider the following instructions..Assume that the probability that the jump instruction will be…

A: 1 Delay Slots A machine encompasses a 5 stages pipeline consists of fetch, decode, execute, letter…

Q: 2. REPE instruction is equal to JNZ instruction. 3. SAL and SHL don't have the same operation. 4.…

A: As part of Q and A guidelines, we are only supposed to answer 3 questions, so solving 3 questions.…

Q: Assume AL=42h; CL=05. Write the content of AL after RCL AL, CL - showing the calculation steps.…

A: Initially      AL=42H, CL=05     CL=1 We need to find content  after RCL AL,CL  ;  // AL=01000010…

Q: For a given number of instructions, assume CPI is increased by 20%, and clock cycle time is…

A: The CPI is increased by 20%, so we can add 0.20 to CPI The clock cycle time is decreased by 20%, so…

Q: H\W: Assuming the SP-1236, Ax=24B6, DI= 85c2 and Dx=5f93n show the content of the stack and the…

A: Actually register is used to store the data or information. In that AX,DX,PX,BX,CX  are the general…

Q: Assume the following are given CS=9345H, DS=2835H, SS=9326H, ES=1955H, IP=2233H, BX=C235H, SI=3D32H,…

A: Actually, given information is: CS=9345H, DS=2835H, SS=9326H, ES=1955H, IP=2233H, BX=C235H,…

Q: H\W: Assuming the SP-1236. Ax-2486. DI= 85c2 and Dx-5f93, show the content of the stack and the…

A: Given Data: SP = 1236H AX = 2486H DI = 85C2H DX = 5F93H   ADD AX,SP: Add values of AX and SP and…

Q: Q1/ two bytes 32 and 17 stored at (0500H] and [0501H] respectively. Write an instruction sequence…

A: The provided things are as follows: Given:- Two bytes 32 and 17 are stored at [0500H] and [0501H]…

Q: 0S Let the clock cycles required for various operations be as follows: Register to trom memory…

A: The answer for total number of clock cycles is

Q: Question// calculate physical addressing mode for the following instruction MOV AX,[BX].ALPHA if…

A: GivenMOV AX,[BX].ALPHA we have given S= 0200H, ALPHA=AB54H and [BX]=9000H

Q: AIM: To write 8085 instruction sequence to calculate and display Fibonacci Series for first 10…

A: Write 8085 assembly instructions to calculate and display the Fibonacci series for first 10 Numbers…

Q: Question// calculate physical addressing mode for the following instruction MOV AX,[BX].ALPHA if…

A: The way of specifying data to be operated by an instruction is known as addressing modes. This…

Q: Q1/ two bytes 32 and 17 stored at [0500H] and [0501H] respectively. Write an instruction sequence…

A: Given:- Two bytes 32 and 17 are stored at [0500H] and [0501H] respectively.  The following…

Q: design a multi_cycle MIPS processor for the following instruction set: lhu (load halfword unsigned)…

A: design a multi_cycle MIPS processor for the following instruction set: lhu (load halfword unsigned)…

Q: 22. Suppose that DS = 0200H, BX = 0300H, and DI = accessed by each of the following instructions,…

A: The Answer is

Q: 1- Explain what operation is performed by each of the instruction that follow a. MOV AX,0110H b. MOV…

A: 1) MOV AX, 0110H It will move value stored in immediate operand in 0110H to AX   2)MOV D1,AX Data…

Q: Assume that AO - SN where N is your student number, and X is the sum of the least significant four…

A: MOVE.L INSTRUCTION Syntax: MOVE.L l,D0 Move the content of memory location l into D0.  Given…

Q: Question// calculate physical addressing mode for the following instruction MOVv AX,[BX].ALPHA if…

A: In the above instruction S=0200H, ALPHA=AB54H, and [BX]=900H are given. The data segment register…

Q: 1. If AX = 1001H and DX = 20FFH, list the sum and the contents of each flag register bit (C, A, S,…

A: Flag registers are used for special purposes to hold resulting value after the arithmetic operations…

Q: calculate the rate of MIPS by executing a program that has 600 MHz processor and 1 million…

A: Total execution time = Total CPI*Total # of instruction*clock cycle time.    Total CPI = 0.3*1 +…

Q: a. Tabulate the memory accesses required for the complete fetch and execution of the following…

A: a) Usually, the LDR instruction is used to load something from memory into a register. Now the…

Q: "uppose we have the instruction Load 500. Given that memory and register R1 contain the values…

A: Instruction Load is 500 So, Assuming R1 is implied in the indexed addressing mode. Immediate…

Q: Which segment will be accessed for the instruction MOV [BX],AH.

A: AX – This is the accumulator. It is of 16 bits and is again divided into two sub-8-bit registers AH…

Q: B- If AX = 34E5H and BX = 288DH, write a short sequence of instructions to exchange the contents of…

A: Answer:-

Q: B- If AX = 34E5H and BX = 288DH, write a short sequence of instructions to exchange the contents of…

A: I have answered this question in step 2.

Q: The following instruction is executed. Assume that before execution, register R15 contains 0x18, and…

A: answer    R15 contains =0x18 ZF=1 AF=0; CF=0;

Q: (B) - Identify the addressing mode for the following instructions then compute the physi for a…

A: 1)LDS SI, [200H]   LDS reads two words from the consecutive memory locations and loads them into the…

Q: Question//Evaluate the following arithmetic (5 * A) + (8 * B) 1- Zero addressing instruction 2- One…

A: Zero Address Instruction - A stack-based computer does not use the address field in the…

Q: Assume the following latencies of stages of a MIPS processor: IF ID EX МЕМ WB 150 ns 200 ns 250 ns…

A: Given Data : IF stage execution time  = 150 ns ID stage execution time  = 200 ns EX stage execution…

Q: Example 2: Define machine cycle, describe the contents of the address, data and control bus lines…

A: Given:

Q: Example 2: Define machine cycle, describe the contents of the address, data and control bus lines…

A: given data

Q: Example 2: Define machine cycle, describe the contents of the address, data and control bus lines…

A: using given data first we need to define machine cycle and given instruction is MOV [2400H], BX and…