Antenna Tank Circuit L Germanium Amplifier Diode To Speakers 12 pF - 120 pF Vout 4.7 nF 100 ka R2 Low Pass Filter R1 Figure 4 Figure 4 shows a radio receiver circuit. The antenna that receives radio signals can be modelled as an AC current source, I,. The antenna is connected to a "Tank Circuit" that consist of an inductor with inductance L, and a variable capacitor, and then connected to the ground. When the capacitor is tuned to the right value, a very high voltage Vo is generated to send signals through the Germanium diode, and the signals are passed into an amplifier system and then converted to sound in the speakers. If the inductance L is given as 1.0 micro-Henries, determine the capacitance values (in pico- Farads) to tune to your favourite Radio Stations in Malaysia listed in the table below: Radio Station Frequency, Angular Tuned Name f Frequency, o Capacitance, pF 988 FM Best FM 98.8 MHz 104.1 MHz Mutiara FM 95.7 MHz Nasional FM 88.5 MHz ||

Antenna Tank Circuit L Germanium Amplifier Diode To Speakers 12 pF - 120 pF Vout 4.7 nF 100 ka R2 Low Pass Filter R1 Figure 4 Figure 4 shows a radio receiver circuit. The antenna that receives radio signals can be modelled as an AC current source, I,. The antenna is connected to a "Tank Circuit" that consist of an inductor with inductance L, and a variable capacitor, and then connected to the ground. When the capacitor is tuned to the right value, a very high voltage Vo is generated to send signals through the Germanium diode, and the signals are passed into an amplifier system and then converted to sound in the speakers. If the inductance L is given as 1.0 micro-Henries, determine the capacitance values (in pico- Farads) to tune to your favourite Radio Stations in Malaysia listed in the table below: Radio Station Frequency, Angular Tuned Name f Frequency, o Capacitance, pF 988 FM Best FM 98.8 MHz 104.1 MHz Mutiara FM 95.7 MHz Nasional FM 88.5 MHz ||

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q/ Discuss how you can convert the square wave into the sinewave of fundamental frequency.
What is the advantage of using square wave-form as an Input Signal? What is the shape of the outputwhen the input signals are sinusoidal and triangular in shape? (Hint: Use Function generator andOscilloscope to observe the output)
Question A sinusoidal signal with a peak voltage of 10V is input into a frequency dependent circuit. What is the peak voltage at its -6dB frequency?
Determin: Frequency of the carreir signal (Hz):...........
please solve value of Capacitor with 0.1V Ripple. And draw output ripple waveform. Explain it one by one for me thanks..
product of (7(cos70+jsin70))(6(cos150+jsin150)) in polar form
Find the Igms value of the square waveform of Figure Q1) cof Figure Waveform
A schematic design of a full-wave bridge type power supply is given below. Provide the appropriate values for the inductors, diodes, capacitor and resistors, such that the output DC voltage is 7.5 V and the max. output power for the load resistance is 20 mW (percentage error for output voltage and output power is 2%). AC voltage source: Amplitude=311.13, Freq=60, DC offset= 0. For the rectifier part, choose diodes with an appropriate PIV rating. Show all the formulas and computations involved in acquiring the values for the inductors, diodes, capacitor and resistors. • In choosing your Zener diode, consider the output voltage and the output current. Note that the output current should be the minimum Zener current. • For the value of the series resistor RS, choose a lower value for less ripple but always consider the required output voltage. •The ripple voltage peak-to-peak value should be less than or equal to 1% of the required output voltage. Use the formula below for choosing the…
what is polyphasic Ac waveforms with diagram
Q6. What is the purpose of harmonic standards? Provide a summary of comparison of IEEE and IEC standards. Write the purpose of the following international standards shown in Table- 2: [12] Table-2 Sr No 1 IEEE-18 Standards Description 2 IEEE 518 3 IEEE 519 4 IEEE 1159 5 IEEE P1433 6. IEEE P1453 7 IEEE P1564 8 IEC61000-3-2 9 IEC 61000-4-7 10 IEC 61642 11 IEC SC77A/WG9 12 IEC SC77A/WG2
Determine: a) Describe how the square wave can be created by adding a fundamental frequency. Show this re-lationship graphically. b) Describe how the triangular wave can similarly be created by adding a fundamental frequency.Show this relationship graphically.
A schematic design of a full-wave bridge type power supply is given below. Provide the appropriate values for the inductors, diodes, capacitor and resistors, such that the output DC voltage is 6.2 V and the max. output power for the load resistance is 20 mW (percentage error for output voltage and output power is 2%). AC voltage source: Amplitude=311.13, Freq=60, DC offset= 0. For the rectifier part, choose diodes with an appropriate PIV rating. Show all the formulas and computations involved in acquiring the values for the inductors, diodes, capacitor and resistors. In choosing your Zener diode, consider the output voltage and the output current. Note that the output current should be the minimum Zener current. For the value of the series resistor RS, choose a lower value for less ripple but always consider the required output voltage. The ripple voltage peak-to-peak value should be less than or equal to 1% of the required output voltage. Use the formula below for choosing the value…