An RTD is connected to a quarter bridge circuit with 1200 matched resistors and 10V power supply and has the following characteristics: 12002 at 0°C℃ α = 0.0032 Ω/Ω/°C Linear from -10°C to 110°C If the bridge voltage is 0.2V, what is the temperature measured by the RTD? Your answer should be in degrees Celsius.

An RTD is connected to a quarter bridge circuit with 1200 matched resistors and 10V power supply and has the following characteristics: 12002 at 0°C℃ α = 0.0032 Ω/Ω/°C Linear from -10°C to 110°C If the bridge voltage is 0.2V, what is the temperature measured by the RTD? Your answer should be in degrees Celsius.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A stabilization circuit has a stability factor of 0.04 and an internal resistance of 5 2. The unstabilized voltage can vary between 75 and 100 V, and the load current can vary from 40 to 80 mA. Determine the maximum and minimum values for the stabilized load voltage.
9. Compute the bias point of the circuit depicted in Figure Vcc=2.5 V 100 ΚΩ Σ1 ΚΩ KQ₁ + 0.5 V- OVCE=738V and IC=1262A OVCE=0.738V and IC=0.001262A OVCE=0.0738V and IC=0.1262A None of the mentioned. OVCE=0.738mV and IC=1262mA
wit Determine Ssketch the output voltage mave form? 1MF- pvi/v 200KR Viown 80807 -4
Sketch the DC load line for the fixed bias circuit and place the Q-point on it. - (1.24 MA, Io.76V) %3D Q - Peint Vcc =+12V RC 1k2 RB 1 MQ BC107 Vc VB Quantity Measured VB 0-6 28 volt 07-82 V1t 0.628 volt VC V BEQ IBQ 0-0000|13,A A 0-00418 A 0.782 Uolt IcQ V CEQ Bac
In the circuit shown in the figure, Rs = 1.88Kohm, R1 = 1201.67Kohm, R2 = 5.72Kohm, R3 = 59.80Kohm, R4 = 15.44Kohm, R5 = 3.15Kohm, R6 = 1.05Kohm, Ry 94.19Kohm, VCC1 = 11.00V, %3D VCC2 = 10.00V, Beta1= 126.00, Beta2= 248.00, VT = 25mV, IVBE| = 0.7V and OPAMP is ideal, calculate the absolute value of the voltage gain (IVO/VS|) of the circuit relative to the source (The %3D result will be positive).
plot the digital signals 1-101010011 2-111001100 using 1-on-off(Rz) 2-polar(RZ) 3-bipolar (RZ) 4-on-off(NRZ) 5-polar (NRZ)
Draw the small signal equivalent circuit of the following circuit. Note that C1 and C2 are large AC coupling capacitors. 5 VIO C1 RF Q1 C2 fem RL Vo
(c) A 2400 V, 1000 KVA, 0.85 power factor (PF) lagging, 50 Hz six-poles, Y-connected synchronous generator has a synchronous reactance of 1.4 2 and an armature resistance of 0.15 2. At 50 Hz, its friction and windage losses are 25 kW, and its core losses are 15 kW. The field circuit has a DC voltage of 230 V, and the maximum IF is 10 A. The resistance of the field circuit is adjustable over the range from 20 to 200 £2. The Open Circuit Characteristic (OCC) of this generator is shown in Figure Q1(c). Calculate the internal generated voltage, EA of this machine at rated conditions. (i) (ii) (iii) Determine the required field current to make Vr equal to 2400 V when the generator is running at rated conditions. If this machine is operating at rated conditions, determine the input torque, TAPP that must be applied to the shaft of this generator.
2- For the circuit given below : Vin is a sine wave Vinpp=9 V and Vref=2.4 V , Assume Vsat=±12V Name the circuit and draw the input and output waveforms . Vo Vin Vref +
In the circuit given in the figure | VBE | = 0.7V, R1 = 17.07Kohm, R2 = 64.82Kohm, RC = 1.49Kohm, RE = 4.46Kohm, VCC = -11.00V, Beta = 125.00, calculate the IC current by full analysis. When making your transactions, 2 steps will be taken after the point. Select the closest option according to +/- 10% margin of error. There is only one correct answer to the question. vcc RE C1 R2 Q1 c2 RC R1
QUESTION 8: A Widlar current source has the configuration shown in the following figure. Assume the bias voltages of V* = 7.5 V and V = -7.5 V. Also assume VBE1 = 0.7 V. Design the circuit such that IREF=1.2 mA and Io=13 µA. Format : 68.642879589768 Format : 3.0902422522623 R1 (kN) RE (kN) V+ Ic2 = lo IREF R1 Ro oVc2 Q2 + + V BEI VBE2 IE2 RE V-
Why was the smoothing capacitor C1/47 not placed directly after the unit bridge? It was placed in its place in the circuit, where its work as a smoothing filter for the base voltage of transistor Q1 was deliberately stopped, but it works with the rest of the circuit elements. Capacitor C1 is isolated between transistor Q1 and the rest of the circuit by a diode (1N4001).