An inverter which produces the output voltage shown the figure above is used to supply the series R (-10[Ohm]) and L(-20 [mH]) load. Determine the Total Harmonic Distorsion (THD) of the load current up to n 3 for the DC input voltage 125 [VI, the output frequency of 60 [Hz), and a=25[Degree] O 32.60% O 23.60% O 5237% O 19.45% O 44.25% O 13.02% O 16.88% O 2953%

An inverter which produces the output voltage shown the figure above is used to supply the series R (-10[Ohm]) and L(-20 [mH]) load. Determine the Total Harmonic Distorsion (THD) of the load current up to n 3 for the DC input voltage 125 [VI, the output frequency of 60 [Hz), and a=25[Degree] O 32.60% O 23.60% O 5237% O 19.45% O 44.25% O 13.02% O 16.88% O 2953%

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

In a rectifier circuit , DC output voltage and RMS output voltage is 0.3 V & 0.48 V respectively. The form factor of this circuit is ___________________.
A. For the circuit diagram shown below, determine and sketch the output voltage (Vout). 1_ohm GaAs 1 ohm 1_ohm Ge Si A 1_ohm. 6_Vpeak w. Vout)
An ideal boost converter is required to have a constant output voltage of 12 V at 24 W load.The input voltage varies from 2.7 to 4.5 V (as in a battery cell). Select a switching frequency of100 kHz. The value of the inductance in the boost converter is 2.2 uH. Determine:(a) The range of duty cycle that the converter will operate with (hint: mode?), and(b) The minimum value of the output capacitance such that the pk-to-pk load voltage rippleis less than 2%.
A Capacitor filter is used at the output across the load in order to minimize the ripple factor of the output voltage. The expressions of the average output voltage Vpc and the output AC component VAc are given below. If R = 1k2 and the single phase bridge rectifier supplied from a 120V - 50 Hz sinusoidal source, then the capacitor value that will maintain the amount of the output ripples to less than 4% would be equal to: VDC = Vm(4FRC – 1)/4ƒRC) VAC = Vm/(4/2ƒRC) Select one: O a. 63.39uF O b. 33.2uF O c. 93.39UF O d. 126.2uF TOSHIBA
Q1. a) Figure Q1 is a single phase 2-level voltage source converter (VSC) with a total DC voltage V-1000V. A PWM scheme, by comparing a reference value with a 1kHz triangular waveform, is used to control the switches S₁ and S2, and output 340v at Vo. With the aid of graphs explain how pulse signals for the switches are generated, sketch the output voltage Vo, determine the duty cycle and the modulation index. Va + 2 it Va d + TS₁ V {1+5₂ = Figure Q1 A single phase VSC
QUESTION 1 Design a high efficiency 3.3 V, 5A d.c.to d.c. power converter from a 4 to 5.5 Vdc source. The maximum allowable inductor current ripple and output voltage ripple are 0.1A and 20 mV, respectively. Assume a switching frequency of 20 kHz. a) Design a suitable converter power circuit using a MOSFET switch, showing all calculation of inductor and capacitor values and drawing a circuit diagram of the final design including component values. Indicate the peak inverse voltage and forward current rating of any diode required, and the maximum drain- source voltage of the MOSFET. b) On the Schematic diagram, draw the path of the current flow during the ON time and the OFF time. c) Describe the effect of changing the values of the inductor and the capacitor in the circuit. d) What is the effect of switching frequency in the circuit? e) Draw the schematic diagram of a circuit with the output voltage higher than the input voltage.
Please written by computer Answer the following questions:a. Name a suitable topology that can be used in the above DC/DC converters to achieve the required regulation with the minimum provided efficiency.b. Calculate the efficiency of the linear regulator.c. Calculate the total input power and the input current.d. Calculate the overall efficiency of the system.e. If a 100uF capacitor is used at the input to minimize the ripple. Assume the rise time of the input source is 0.2ms. Estimate the maximum inrush current to charge the capacitor to 12V.
Part 1) Consider a step down converter with a resistive load. It is supplied by a DC power source of magnitude Vs = 160 V. The switching period is 0.25 ms and the duty cycle k is first set to 0.5. The load is resistive with R=10 Ohms. The critical value of L and the critical value of C are equal to: a. 0.625mH and 0.392uF b. 0.625mH and 0.196uF c. 0.312mH and 0.196uF d. None of these Part2) Now consider the same given but the load is an inductive load with R=10 Ohms and L=10 mH. The switch is ideal. Calculate The RMS load current Io and the RMS converter current Ir are equal to: Select one: a. 5A and 3.54A b. None of these c. 8A and 5.66A d. 12.5A and 8.84A
The neutral current is equal to three times of ....... sequence current.
1) 169sin 377t a) What is the peak factor? b) What is the form factor?
iii. For fully controlled single phase bridge rectifier with inductive load (load current is continuous) ,supply voltage 220 V(RMS) and a=30° .The mean value of output voltage is : (a) 150.32V (b) 171.52V (c) 120.98V
(a) Plot the even and odd parts of the signal of Figure