An electron is fired at a speed v = 3.1 x 10° m/s and at an angle 0, = 36.8° between two parallel conducting plates as shown in the figure. If s 1.8 mm and the voltage difference between the plates is AV = 98.8 V, determine how close, w, the electron will get to the bottom plate. Put your answer in meters and include at 6 decimal places in your answer. Do not include units. The x-axis of the coordinate system is in the middle of the parallel plate capacitor. !!

An electron is fired at a speed v = 3.1 x 10° m/s and at an angle 0, = 36.8° between two parallel conducting plates as shown in the figure. If s 1.8 mm and the voltage difference between the plates is AV = 98.8 V, determine how close, w, the electron will get to the bottom plate. Put your answer in meters and include at 6 decimal places in your answer. Do not include units. The x-axis of the coordinate system is in the middle of the parallel plate capacitor. !!

University Physics Volume 1

18th Edition

ISBN:9781938168277

Author:William Moebs, Samuel J. Ling, Jeff Sanny

Publisher:William Moebs, Samuel J. Ling, Jeff Sanny

Chapter1: Units And Measurement

Section: Chapter Questions

Problem 15P: Use the orders of magnitude you found in the previous problem to answer the following questions to...

See similar textbooks

Similar questions

Give an educated guess for the requested values of in Volts expressed as integer numbers, i.e. no decimal place necessary.(Find all values) 1. Vout(0+) = 2. Vout(pi/40) = 3. Vout(pi/20) = 4. Vout(pi/15) = 5. Vout(pi/10) = 6. Vout(pi/5) = 7. Vout(infinite) =
QUESTION 6 Find the uncertainty in a calculated electrical potential difference from the measurements of current and resistance. Electric potential difference depends on current and resistance according to this function V(I,R) = IR. Your measured current and resistance have the following values and uncertainties 1 = 1.5 Amps, Sl = 0.2 Amps and R = 36.4 Ohms and SR 0.3 Ohms. What is the uncertainty in %3D the , SV ? Units are not needed in your answer.
Pls. refer to the answerk eys so that I will know if my solution is wrong
ANSWER THE PROBLEM, MAKE SURE THAT YOUR SOLUTION IS READABLE AND YOUR FINAL ANSWER SHOULD BE IN 4 DECIMAL PLACES.
The active area of the amd ryzen 5950x processor in high end computers today has about 19.2 billion transistors (transistors are semiconductor device that control electronic processes). The dimensions of the die sizes are 2x 80.7 + 125 (I/O) mm2 (please refer to the image below.). What are the dimensions of one transistor on the die, assuming that all of the area across the die is transistors and each is a square?
How can I solve this problem? A 12 nC charge is located at (-4, 0) and a -9 nC charge located at (4, 0) exerts a net force on a 3 nC charge located at (0, -3). Assume that the coordinates are measured in millimeters. a) Calculate the y-component of the force exerted by the -9 nC charge, in millinewtons, to the 3 nC charge. b) Calculate the direction of the net electric force, in degrees, experienced by the 3 nC charge. Use the positive x-axis as reference. c) Calculate the electric potential energy experienced by the 3 nC charge in microjoules. d) Calculate the electric potential at the origin in kV/m.
If k = 0.207, how long will it take a battery to reach a 60% charge? Assume that the battery was fully discharged when it began charging. (Round your answer to one decimal place.)
An electron volt, eV is a unit of energy,. Which is larger, a GeV or MeV?
Express each of the following as requested: -5 a. 2.34 x 10 eV in decimal notation. b. Express 891 MeV in scientific notation. c. Express 7.4 x 10-4 sec in msec.
Cylindrical-conductors has inner and outer radii of 25 mm and 50 mm, respectively. If V(p = 25 mm) = 0 V and V(p = 50 mm) = 300 V, ɛr = 15 %3D calculate : a. V, E, and D at p = 40 mm b. Ps on each plate. %3D
1. 1500 200W 370 comple 150N Ř= ? IR = ? x = ? OB. 2. Given A(2, -3,1), B(0, 0, 2); and ((2, 2, 0), find 08.
1.4 Analyze the circuit shown in Figure 1.35. Assume circuit and diode parameters of VDD=5V, R=5kN, VDon0.6V, and v=0.1sinot (V). VDD R vo (a) Figure 1.35