An audio power amplifier delivers an 80-volt peak 35 Hz sine to a subwoofer. If the subwoofer impedance at this frequency is 4 at −30°, determine the peak current delivered to the load and the true power.

An audio power amplifier delivers an 80-volt peak 35 Hz sine to a subwoofer. If the subwoofer impedance at this frequency is 4 at −30°, determine the peak current delivered to the load and the true power.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.4P

See similar textbooks

Related questions

Q: 13.8 kV Source Load m 1.5KG

A: Given data, Circuit diagram is given as,

Q: 2.10 In the circuit of Fi 2.67, a decrease in R3 leads to a decrease of: (a) current rough R3 (b)…

A: Answer: b, d Explanation: a. It is not a valid option. The resistance and current are inversely…

Q: 2Ω O5V Ε 20 V 3Ω 4Ω 52-54. The voltage v across the current source in the circuit is: 20 V 15 V 10 V…

Q: V ΤΟ 20 Ω Μ j10 Ω Μ 40 Ω j30 Ω Ξ 30 Ω Μ j60 Ω

Q: Grinding Force →→K₂(Rs+1) Machine Stiffness 1 Deflection ms2+bs + k Control Filter 1 1 Additional…

A: The given system is shown below: The first closed-loop system is a negative feedback system, the…

Q: Q4) let V (cos 20)/r in free space; find the volume charge density at point. A(0.5,60°,1).

A: In this question we will find volume charge density from potential....

Q: a group of incandescent lamps draws 7.4 A, from a 120v supply. due to a small resistance in the wire…

A: A group of incandescent lamps draws 7.4 A, from a 120v supply. Due to a small resistance in the wire…

Q: What is the reason why there is either lower or higher voltage error in the output? (for example,…

A: Error: Error is a difference between the true value and measured value. Every meter has some error,…

Q: Assuming that there are no charges in the four regions shown in the figure, which of the patterns…

A: The electric field lines originate at a positive charge and terminate at a negative charge. In…

Q: A voltage source with a source resistance of 12 is connected to a low pass Butterworth filter (Both…

Q: 37. Fig. 2.28 shows a part of a closed circuit What is the potential difference between points A and…

A: Given a part of closed circuit,

Q: C. Find the Fourier transform of f(t) = 28 (t + 2) - 28(1-2).

Q: Considering the system shown below: R(s) (s+a) (s+b) S PID controller Plant G(s) G(s) a. Set-up the…

A: The proportional integral derivative controller produces an output, which is the combination of the…

Q: PROBLEM: Find the number of branches in plotting root locus. R(S) K s(s+ 1)(s² + 4s +13) C(s)

A: In this question, We need the determine the number of branches in plotting root locus?

Q: Consider two systems A and B connected with each other and bound to stop and wait protocol. System A…

A: Let p is the error rate and X is the actual packet Total send packet =Y Y=X( 1+p+p2 +p3 +........)

Q: A λ / 2 dipole , with a total loss resistance of 1 ohm , is connected to a generator whose internal…

A: Antenna:- It's main purpose is to transmit and receive signals between wireless points. It consists…

Q: A balanced delta-connected load with impedance per phase of 30230° 2 is connected to an abc-sequence…

A: It is given that: Z∆=30∠30° ΩeAC=-1202cos120πt-π6 V

Q: . The magnetic field intensity is given in the region defined by H = z²ax + x³ay + y^az A/m. Find…

Q: Consider the RL circuit below. UI a. Obtain the transfer function H(s) = Vo/V₁. b. Find the relation…

Q: A current of 10A flows through a conductor an 10W is dissipated. What p.d. exists across the end of…

A: Given: Current flow through conductor, I = 10 A Power dissipated, P = 10 W

Q: A 280 V, separately excited DC motor with armature resistance of 122 and constant field excitation…

A: In separately excited motor, Flux remain constant generally Back emf of a DC machine depends on…

Q: f. oooo M x(1) f(n)

A: In mechanical network interconnection of mechanical network along a circuit diagram. In mechanical…

Q: 1000 Ω W R m ig 160 nF 100 mH ?For the circuit shown above, what is the average power supplied by…

Q: S 20V $2,4k -Vo Ivonz6m14 Vasen = 8V Vesth=6V 15m= 50ms 3m-20m 1k 610N for the cascade amplifier,…

A: Voltage gain Input resistance Output resistance is found. While finding output resistance previous…

Q: An AM signal of 50 watt power is transmitted in a frequency range 200 - 210 kHz in a transmission…

A: given an AM signal of 50 watts power is transmitted in a frequency range 200-210KHz in a…

Q: Find the general Solution of (Q(t)) cst Ite circuit of the given values : R = 102 c=10-2² F E (t) =…

A: An RLC circuit is an electrical circuit consisting of a resistor (R), an inductor (L), and a…

Q: 2. Find Vo in the circuit of figure shown below using Kirchhoff's law and Maxwell Analysis. -6Q -j4Q…

A: The Problem can be solved by using mesh analysis and kirchhoffs law. The calculation is shown in the…

Q: A non-magnetic circuit has a reluctance of 38.6 gilbert per maxwell. Calculate how much flux will be…

A: Here the concept & the calculations related to the magnetic circuit. Given :- Reluctance R=38.6…

Q: Determine the current flowing through an element if the charge flow is given by (a) q(t) = (3t+ 8)…

Q: Calculate the capacitor's voltage for t 0 for the following circuit a) 2 F 12 V X=0 www 352 b)…

Q: HW1. Find the transfer function H(s) = Figure 1. 192 120.5F 1Η 402 V(t) www lo (s) 1₁ (s) 292 www in…

A: We need to find out the transfer function .

Q: Assuming ( 4 7 )₁ = (abcdefg), consider the Boolean function F(A,B,C,D) given by the following truth…

A: Brief description: For the above given decimal number we need to implement the minterms by using 8×1…

Q: Find the total impedance, voltage drop on the 100-ohm resistor, draw the phasor diagram of the…

A: Current and voltage always in phase incase of resistance Current lag by 90 degree with respect to…

Q: 1.4 A charge of 2 C flowing past a given point each second is a current of 2 A. (a) True (b) False

A: A charge of 2 C flowing past a given point each second is a current of 2 A. To select correct answer

Q: A 220 V self-excited shunt motor has armature and field resistances of 0.2 Ω and 220 Ω respectively.…

A: In this question we need to find a new speed in rpm (rev/min) if an external armature resistance of…

Q: Refer to the figure; the value of VBE İS: Rc470 ft Ra www 5 kf Vas SV → O 0.7 V O 1.2 V O 0.079 V O…

Q: 15) The saturation current of ap- junction diode is 350 mA and the operating temperature is 295 K.…

A: Brief description: Here we need to calculate the value of reverse biased voltage to get the reverse…

Q: Determine the z-transform and ROC of the given signal: -n x(n) = (G) u(−n)-n-5^u(−n − 1) + 2^(n

Q: Two single-phase transformers, one of 100 kVA and the other of 50 KVA are connected in parallel to…

A: Given data, Rating of transformer S1=100 KVA, S2=50 KVA Resistances are given 2% and 5% Reactance's…

Q: R1 Vs R2 +21 www R3 R4 ?For the circuit shown in the figure above, what is the value of the…

A: Brief description: In the above given question we need to calculate the value of capacitor voltage…

Q: For the circuit given, obtain vi and v2. 2 Ω για 10 Ω 3A www www 5Ω 64 4Ω A) v = 0 V, va = -12 V = 0…

A: Nodal Analysis- The mathematical method for calculating the distribution of voltage between the…

Q: Q2: Astable multivibrator was designed using a 555 timer. The frequency of the output signal should…

Q: Determine the value of the source current, designated by I, and the total power delivered to the…

A: The required parameters can be calculated by using ohms law and resistor reduction method.

Q: Find the laplace transform ol (22) of е-е

Q: One side of a transformer has 1,800 turns while the other side has 450 turns. The high voltage side…

Q: 1. Obtain Zin in the circuit 50 Ω Zina j30 Ω m -j100 Ω 40 Ω 60 Ω j20 Ω

A: The given circuit is shown below: On simplifying the above circuit, by solving the equivalent of…

Q: Subject: Quality engineering Mention examples of problems in real life, in which some…

A: In field of electrical engineering,, the quality is power flow, efficiency, and the circuit. The…

Q: 89. If the ripple voltage in a full-wave rectifier is 25 V at a load current of 60 mA, its value at…

A: Given, Ripple voltage of full wave rectifier, VR1=25 V At load current, IL1=60 mA Ripple voltage,…

Q: Q3) Obtain frequency and impulse response of type III - correlative level coding scheme. Plot…

A: Correlative coding is also known as partial response signalling schemes which are used to obtain a…

Q: Q18. In the R-L-C series circuit shown, suppose R = 200 2, L = 70 mH, C = 2.0 μF, Vmax=80V and the…

A: As per guidelines given to us we can only provide the solution of first three subpart in multi part…

Concept explainers

Power Amplifier

The power amplifier is an electronic amplifier designed to maximize the signal strength of a given input. The input signal strength is enhanced to a high enough level to drive output devices such as speakers, headphones, RF (Radio frequency) transmitters, etc. Unlike voltage / current amplifiers, the power amplifier is designed to drive core loads directly and is used as a storage block in the amplifier series.

Maximum Efficiency Criterion

In every field of engineering, there is a tremendous use of the machine and all those machines are equipped for their popular work efficiency so it very much important for operation engineers to monitor the efficiency of the machine, planning engineers to check out the efficiency of the machine before installing the machine and design engineers to design machine for higher efficiency than and then the utility will procure their products that will ultimately lead to profit and loss of the company. It indicates the importance of efficiency right from the initial stage as manufacturing units, intermediate stage as planning coordinators, and end-users stage as a utility.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Derive the average and rms values of output voltages and currents for three phase semi converter. Power Electronics
A load consists of XL=70 and XC=150 are connected in parallel across 120 Volt supply.The reactive power of the circuit is.......
A single-phase, 60 Hz(input) convertor, such as shown below, operates at a synchronous carrier frequency of 300 Hz, The DC Link voltage is 680 V, and the effective value of the fundamental AC voltage E34 is 430 V. Calculate; 1) The duty cycle D, and Ton when the AC voltage is 500V. 2) The duty cycle D, and Ton when the AC voltage is -30V. 3) Draw the waveform of the convertor output. 5 EL 4-quadrant switching converter EH 2 4 6 D Se
In a single-phase half-wave ac-dc converter, the average value of the load current is 1.78 A. If the converter is operated from a 240 V, 50 Hz supply and if the average value of the output voltage is 27% of the maximum possible value, calculate the following, assume the load to be resistive. (a) Load resistance (b) Firing angle (c) Average output voltage (d) The rms load voltage (e) The rms load current (f) DC power (g) AC power (h) Rectifier efficiency (i) Form factor (j) Ripple factor
4) A single-phase full-wave AC voltage controller consists of two SCRs connected in invers-parallel. The supply voltage is 220V at 50Hz. The controller is used to control heater element of 2500W in an electric oven. The trigger angle is 30o. i) Draw the circuit diagram ii) sketch compatible waveforms for the supply, load and SCR voltages. iii) calculate the rms value of the load voltage and current. iv) Determine the input power factor of the circuit. v) Calculate the average value of the SCR current.
Q2) A 3-phase, half-wave thyristor converter is connected through a voltage source 150 V as input voltage and used to supply resistive load of 10 N. Determine rsm voltage, rms current, ripple factor and dissipated power in the resistor R. If a = 45° and f = 50 Hz.
What is the ripple factor and what causes it? Discuss and explain how this factor can be used as a metric to improve the quality of the designed AC to DC converting system
Design of a DC-DC Converter. The Circuit Below shows a basic Buck-Boost Converter with a highly inductive Load. With a Deliberate mistake in the configuration of the Circuit Connection. The Value of L1 is 22mH, C1 is 10uF, R1 is 220 and L2 is 10mH. The circuit operates with a switching frequency of 20KHZ. The Duty cycle of the Clock signal V2 is given by the function below: ( 17 ) х0.2 Duty Cycle, k = 0. 55 + 100 Your Unique Duty Cycle = %3D Buck-Boost Converter Q1 IRG4BC10U D1 R1 222 1N4009 C1 LV1 12V L1 22mH 10µF L2 10mH a) Find the mistake in the configuration of the circuit and correct the connection error.
Q1. a) Figure Q1 is a single phase 2-level voltage source converter (VSC) with a total DC voltage V-1000V. A PWM scheme, by comparing a reference value with a 1kHz triangular waveform, is used to control the switches S₁ and S2, and output 340v at Vo. With the aid of graphs explain how pulse signals for the switches are generated, sketch the output voltage Vo, determine the duty cycle and the modulation index. Va + 2 it Va d + TS₁ V {1+5₂ = Figure Q1 A single phase VSC
A single phase full wave AC voltage controller has a resistive load of 5 ohms and an input voltage of Vs = 240 V (RMS), 50 Hz. The delay angles of both thyristors are set to 45 degrees. The maximum RMS and average current ratings of the thyristor are equal to: Select one: O a. 33.94A and 21.6A O b. None of these O c. 24A and 10.8A O d. 48A and 26.09A Clear my choice
A de chopper has a load resistance of 202 and input voltage V,-220 V. When the chopper is ON, its voltage drop is 1.5 V and chopping frequency is 10 KHz If the duty cycle is 80%, determine average output voltkge, ms output voltage and chopper ON time.
EX1: The AC Voltage controller shown below is used for heating a resistive load of 5 N and the input voltage Vs = 120 V (rms). The thyristor switch is on for n=125 cycles and is off for m = 75 cycles. Determine the RMS output voltage Vo, the input factor and the average and RMS thyristor current.