An armature controlled DC motor has the following parameters: Tf = 0.03 Nm KT = 0.15 Nm/A Imax = 2.4 A KE = 0.15 Vs/rad Wmax = 5000 rpm R = 0.8 Ohms %3D 1. Determine the following: (i) The maximum output torque. (ii) The maximum power output. (iii) The maximum armature voltage. (iv) The no load motor speed when e = Emax

An armature controlled DC motor has the following parameters: Tf = 0.03 Nm KT = 0.15 Nm/A Imax = 2.4 A KE = 0.15 Vs/rad Wmax = 5000 rpm R = 0.8 Ohms %3D 1. Determine the following: (i) The maximum output torque. (ii) The maximum power output. (iii) The maximum armature voltage. (iv) The no load motor speed when e = Emax

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A PWM signal is sent to a permanent magnet DC motor through an H-bridge circuit. The PWM frequency is 100 kHz, the DC voltage source is 16 volts, and the specification of the motor is given as: voltage = 16 volts, no load speed = 1500 RPM, holding torque = 2 Nm. a. Draw the voltage signal delivered to the motor when the duty cycle is 20% and 80% (at least draw for 5 periods). Calculate the speed of DC motor when the duty cycle is 20% and 80%. b. C. Estimate the output power when the duty cycle is 20% and 80%. Assume that the motor efficiency is 100%.
A DC chopper is used in regenerative breaking mode of a dc series motor. The dc supply is 600 V, the duty cycle is 70%. The average value of armature current is 100 A. It is continous and ripple free. What is the value of power feedback to the supply ?
A shunt motor is rotating at 1500 rpm and is powered by a 120V voltage source. The current line resistance is 51-A and the shunt field resistance is 120ohm. If the armature resistance is 0.12ohm, Determine: a) the armature current, b) the back emf (E), c) the total power that is supplied to the motor, d) the power absorbed by the armature, e) power dissipated in the armature. You have to answer all subpart not only first three subpart Either dislike is ready
A shunt motor is rotating at 1500 rpm and is powered by a 120V voltage source. The current line resistance is 51-A and the shunt field resistance is 120ohm. If the armature resistance is 0.12ohm, Determine: a) the armature current, b) the back emf (E), c) the total power that is supplied to the motor, d) the power absorbed by the armature, e) power dissipated in the armature. Please answer all subpart either dislike please I will like it please
A 48kW, 600V, 1500 rpm separately excited dc motor is controlled by single phase semi-controlled converter. The resistance of the armature is 192 and of the field is 1450. The field circuit is controlled by a single phase fully controlled converter and its firing angle is set to 20. The AC supply voltage to the armature and field converters is a single phase 220V, 60 Hz. The voltage constant is 0.946 V/A rad/s. If the armature converter firing angle is 45 and the speed is 1200 rpm; calculate the armature current and the developed torque.
1. Single phase full converter is used to control the speed of separately excited DC motors. AC supply voltage is 208 V. Motor armature and field resistance are 0.5 2 and 345 2 respectively. The field current is also controlled by a full converter and the field current is set as the maximum possible value. Motor voltage constant is 0.7 V/A-rad/sec. If firing angle is 45° and armature current is 55 A, determine the angular speed of the motor. Assume armature and field current are ripple free.
A 10 kW, 250 V Shunt motor has an armature resistance of 0.5 ohm and a field resistance of 200 ohm. At no load and rated voltage, the speed is 1200 rpm and the armature current is 3 A. At full load and rated voltage, the line current Is 47 A and because of armature reaction, the flux is 4 % less than it no load value. a.) What is the full load speed? b.) What is the developed torque at fll load?1158 rpm
Design a DC motor circuit to drive A fan-type load with a torque equation equal to: TL=1.34×10−7ω2TL=1.34×10−7ω2 N.m The fan speed range is from 500 to 1200 rpm. To achieve the required operation, the armature voltage of the motor is adjusted by a single-phase, full-wave, ac/dc converter. The input voltage and frequency to the converter are 480 V (rms) and 50 Hz. choose the motor type, show the motor rating, αα range, Supply voltage, and frequency, and any required other information Modify the design to automatically adjust the voltage drive the load within the specified speed range. show the control variable, controller type, connection, and controller weights.
(b) A 2 pole 220 V, 100A, and 850 rpm separately excited DC motor has an armature resistance of 0.15 0. Two field coils are connected in parallel and used to drive a load with the torque of TL = 400 – 0.2N, Nm Where N is the motor speed in rpm. Armature voltage control and two field windings connected in series are used in speed control below and above the rated, respectively. (i) Calculate the motor armature current and speed when the armature voltage is reduced to 110VV. (ii) Examine the motor speed and current when field coils are connected in series.
5. A 7 ½ Hp, 220 V, long-shunt compound dc motor draws a line current of 3 A when running light. The armature, series field and shunt field resistances are 0.2, 0.2, and 110 ohms, respectively. Determine the line current drawn at rated load.
Design a DC motor circuit to drive A fan-type load with a torque equation equal to: TL=1.34×10−7ω2TL=1.34×10−7ω2 N.m The fan speed range is from 500 to 1200 rpm. To achieve the required operation, the armature voltage of the motor is adjusted by a single-phase, full-wave, ac/dc converter. The input voltage and frequency to the converter are 480 V (rms) and 50 Hz. choose the motor type, show the motor rating, αα range, Supply voltage, and frequency, and any required other information Modify the design to automatically adjust the voltage drive the load within the specified speed range. show the control variable, controller type, connection, and controller weights. design the single-phase, full-wave, ac/ dc converter. show design specifications, the reason for DC motor selection. correct manual circuit, and correct automatic closed-loop control circuit
A250 V, dc shunt motor has an armature resistance of 0.5 chmand a field resistance of 250 chm When driving a load df constant tarque at 600 r.p.m, the armeture current is 20 A If it is desired to raise the speed fram600 to 800 r.p.m, what resistance should be inserted in the shunt field circuit? Assume that the magnetic circut is unsaturated