An aluminum tube is fastened between a bronze rod and a steel rod as shown. Axial loads are applied at the positions indicated. (a) Find the value of P (kN) that will not exceed a maximum overall shortening of 2 mm. (b) Determine the stress in the aluminum tube and the stresses in the bronze and steel rods. Express the stresses in MPa. Indicate whether tension or compression. 3P LB = 0.6 m Bronze A = 450 mm² E = 83 GPa P LA = 1.0 m Aluminum A = 600 mm² E = 70 GPa 4P Ls = 0.8 m Steel A = 300 mm² E = 200 GPa 2P

An aluminum tube is fastened between a bronze rod and a steel rod as shown. Axial loads are applied at the positions indicated. (a) Find the value of P (kN) that will not exceed a maximum overall shortening of 2 mm. (b) Determine the stress in the aluminum tube and the stresses in the bronze and steel rods. Express the stresses in MPa. Indicate whether tension or compression. 3P LB = 0.6 m Bronze A = 450 mm² E = 83 GPa P LA = 1.0 m Aluminum A = 600 mm² E = 70 GPa 4P Ls = 0.8 m Steel A = 300 mm² E = 200 GPa 2P

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.5.25P: A capped cast-iron pipe is compressed by a brass rod, as shown. The mil is turned until it is just...

See similar textbooks

Similar questions

A capped cast-iron pipe is compressed by a brass rod, as shown. The mil is turned until it is just snug, then add an additional quarter turn to pre-compress the cast-iron pipe. The pitch of the threads of the bolt ap = 52 mils (a mil is one-thousandth of an inch). Use the numerical properties provided. (a) What stresses a and arwill be produced in the cast-iron pipe and brass rod. respectively, by the additional quarter turn of the nut? (b) Find the bearing stress ahbeneath the washer and the shear stress t(in the steel cap.
The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the principal stresses and show them on a sketch of a properly oriented element.
Repeat the previous problem using ? = 50° and stresses on the rotated element: sy1= 70 MPa, ??y1=-82 MPa, and tx1y1=-35 MPa.
An element on the top surface of the fuel tanker in Problem 7.2-1 is in biaxial .is in the and is subjected to stresses a, = 6250 psi and a. = -1750 psi, as shown in the figure. Using Mohr s circle, determine the following: (a) The stresses acting on an element oriented at a counterclockwise angle ? = 550 from the x axis. (b) The maximum shear stresses and associated norm al stresses. Show all results on sketches of properly oriented elements.
Answer the ff correctly. The rectangular bar shown is connected to a support bracket with a 24 mm diameter pin. The width of the rectangular bar is 70 mm and its thickness is 15 mm. The bearing stress in the bar cannot exceed 120 MPa. Determine the maximum value of Pmax that can be supported based solely on consideration of the bearing stress in the bar. Note: This question is not asking about any stresses in the support bracket...just bearing stress in the rectangular bar.
A cylindrical tank steel pressure vessel 200mm in radius and 4.0m in length, is subjected to an internal pressure of 3.0 MPa. Determine the thickness of tank (nearest mm) if the following stresses are not to be exceeded: tangential stress of 45 MPa and longitudinal stress of 30 MPa. and also show the free body diagram
The rectangular bar shown is connected to a support bracket with a 24 mm diameter pin. The width of the rectangular bar is 70 mm and its thickness is 15 mm. The bearing stress in the bar cannot exceed 120 MPa. Determine the maximum value of Pmax that can be supported based solely on consideration of the bearing stress in the bar. Note: This question is not asking about any stresses in the support bracket...just bearing stress in the rectangular bar.
Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded, as shown. The diameter of rod (1) is d1 = 1.66 in. and the diameter of rod (2) is d2 = 2.68 in. Determine the normal stresses in rods (1) and (2). Assume P = 17 kips and Q = 29 kips. Use positive for tensile stress and negative for compressive stress.
The rectangular bar shown is connected to a support bracket with a 24 mm diameter pin. The width of the rectangular bar is 80 mm and its thickness is 25 mm. The bearing stress in the bar cannot exceed 120 MPa. Determine the maximum value of Pmax that can be supported based solely on consideration of the bearing stress in the bar. Note: This question is not asking about any stresses in the support bracket.just bearing stress in the rectangular bar. Rectangular bar Support bracket
The element in the image has a horizontal force of 20 N and a vertical force of 25 N. The element was made of a 25.4 mm diameter steel bar. Determine:to. The four states of stress from the farthest place of the forces and obtain the critical point.b. For the critical point, construct the Mohr circle.C. Obtain the maximum principal and normal shear stresses for the critical point.d. The angles at which the maximum normal and shear stresses occur.and. Draw the rotated tension state for the angles obtained and with the corresponding tensions.
A steel pipe 120 mm external diameter and 60 mm internal diameter is subjected to an internal pressure of 15 N/mm2 and an external pressure of 5 N/mm2. Determine and sketch curves showing the distribution of the radial and circumferential stress across the section using Lame’s equations.
1 m Section of connection for AB and BC 1m An elbow shaped frame made of Al 2024 T6 aluminum has a circular cross-section having a radius of 5mm. a. Take a cut through the section where the AB and BC segments are connected (shown in the figure at point B). Define the stress types that will occur on this section as a result of loading on the frame and show the variation of these stresses on the cross-section. b. Drawing a free body diagram, show and calculate the internal loads at point C. Show the stress distribution that are caused by these internal loads on this cross-section. Do the internal loads vary along the beam BC ?