An A36 W14X605 simply supported steel beam with span “L” carries a concentrated service liveload “PLL” at midspan. The beam is laterally supported at supports and its midspan. Consider its beam selfweight to be its service deadload, “w” (use ASEP steel manual for selfweight, w and other section properties). In checking section's compactness, calculate the upper limit for non-compact web category? Express your answer in 2 decimal places.

An A36 W14X605 simply supported steel beam with span “L” carries a concentrated service liveload “PLL” at midspan. The beam is laterally supported at supports and its midspan. Consider its beam selfweight to be its service deadload, “w” (use ASEP steel manual for selfweight, w and other section properties). In checking section's compactness, calculate the upper limit for non-compact web category? Express your answer in 2 decimal places.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter5: Beams

Section: Chapter Questions

Problem 5.5.3P

See similar textbooks

Similar questions

A beam must be designed to the following specifications: Span length = 35 ft Beam spacing = 10 ft 2-in. deck with 3 in. of lightweight concrete fill (wc=115 pcf) for a total depth of t=5 in. Total weight of deck and slab = 51 psf Construction load = 20 psf Partition load = 20 psf Miscellaneous dead load = 10 psf Live load = 80 psf Fy=50 ksi, fc=4 ksi Assume continuous lateral support and use LRFD. a. Design a noncomposite beam. Compute the total deflection (there is no limit to be checked). b. Design a composite beam and specify the size and number of stud anchors required. Assume one stud at each beam location. Compute the maximum total deflection as follows: 1. Use the transformed section. 2. Use the lower-bound moment of inertia.
An A36 W14X605 simply supported steel beam with span “L” carries a concentrated service liveload “PLL” at midspan. The beam is laterally supported at supports and its midspan. Consider its beam selfweight to be its service deadload, “w” (use ASEP steel manual for selfweight, w and other section properties). a. Check for compactness of the given section? b. In checking section's compactness, calculate the upper limit for compact flange category? c. In checking section's compactness, calculate the upper limit for non-compact web category?
PROBLEM 4: The beam shown the figure below is a W16x31 of A992 steel and has continuous lat- eral support. The two concentrated loads are service live loads. Neglect the weight of the beam and determine whether the beam is adequate. a. Use LRFD. b. Use ASD. 60k 60k W16 x 31 asap +4
ASSIGNMENT #5 BIAXIAL BENDING Problem: Check the beam shown for compliance with the NSCP Specification. Lateral support is provided only at the ends, and A992 steel is used, F, = 345 mPa. The 90 kN service loads are 30% dead load and 70% live load. a. Use LRFD b. Use ASD d tw by ty 1x(106) S(10³) mm mm mm mm³ mm mmª W410x100 415 10 260 16.9 398 1920 SECTION Tx mm 177 1m 90 kN 90 KN 1.5m W410x100 I Loaded Section Ly(106) Sy(10³) Ty mmª mm³ mm 49.5 381 62.4 1m Zx(10³) Zy(10³) mm³ mm³ 2130 581
Determine whether the D = 560 kips L = 68 kips compression member shown is adequate to support the given service loads. Take %3D note Pu = 1.4D. 20' W12 x 79 = 3.05 in K = 0.80, r= E = 29000 ksi, Fy = 50 ksi A992 steel Input Yes or No for your final answer. Note: Ag = 23.2 in^2
6 6a 6b 6c Alaterally supported beam was designed for flexure. The beam is safe for shear & deflection. The most economical section is W 6 x 20 however the said section is not readily available at the time of the construction. If you are the engineer in charge of the construction what alternative section will be the best replacement? Why? Use: Fy=248 MPa: E=200,000 MPa Designation W8 x 24 W8 x 21 Weight Ag (mm2) 3787 36 31 width mm kg/m d (depth) 30 157.48 152.91 9.27 W6 x 20 expla'n briefly your cho'ce. (transform your comparative analys's 'nto a narative form to support your cho'ce) W8 x 28 42 204.72 165.99 11.81 5323 4568 201.42 164.97 10.16 3974 210.31 133.86 flange bf thickness tf Web 10.16 thickness tw 6.60 Elastic Properties mm 4 Ix x 106 7.24 6.22 6.35 17 41 34 31 mm 3 Sxx 103 220 398 342 298 mm rx 67.56 87.63 86.87 88.65 mm 4 lyx 106 6 9 8 4 mm 3 Syx 106 72 109 92 61 mm ry 38.10244 41.15 40.89 32 Plastic properties. mm 3 Zx x 103 244 446 380 334 mm 3 Zyx 103 110 166 140 93…
A 1.5" x1.5" solid steel bar is made of a steel having an Fy = 50 ksi and an Fu = 65 ksi. It is loaded in tension by the following unfactored forces: • DL = 30 kips ● LL = 50 kips • SL 10 kips = Determine if the bar yields in tension. Assume LRFD. Use the ASCE 7-22 Load Combos and Factors.
Problem 3b. The built-up shown has Fy=50 ksi MC18X 42.7 W12 X 72 KL = 18.5 ft %3D Find the following: a. The KL/r b. The design strength for LRFD. c. The allowable strength for ASD. d. Is the section? Why?
Use the composite beam tables and select a W-shape and stud anchors for the following conditions: Span length = 18 6 Beam spacing = 9 ft Total slab thickness = 51 2 in. (the slab and deck combination weighs 57 psf). Lightweight concrete with a unit weight of 115 pcf is used Construction load = 20 psf Partition load = 20 psf Live load = 225 psf Fy=50 ksi and fc=4 ksi A cross section of the formed steel deck is shown in Figure P9.8-9. The maximum live-load deflection cannot exceed L/360 (use a lower-bound moment of inertia). a. Use LRFD. b. User ASD.
Determine the design strength of the beam shown. Assume fy-345MPa and fc'-21 MPa.
Using the Yield Strength of Grade 60 Steel, what would be the Maximum load that the 25 mm diameter bar can carry? a 204 kN b 203 kN c 205 kN d 206 kN
Q4/ Give reason PLLA and PDLA are more common used for load-bearing applications?