Air is used for a Carnot power cycle, whose temperature and pressure bounds are 500 K and 300 K, and 750 kPa and 100 kPa, respectively. Consider air with constant specific heats at the average temperature. A. Draw this cycle on P-v and T-s diagrams. B. Find the pressure, temperature and specific volume at each state of the cycle. C. What is the net specific work output of the cycle? D. What is the thermal efficiency of the cycle?

Air is used for a Carnot power cycle, whose temperature and pressure bounds are 500 K and 300 K, and 750 kPa and 100 kPa, respectively. Consider air with constant specific heats at the average temperature. A. Draw this cycle on P-v and T-s diagrams. B. Find the pressure, temperature and specific volume at each state of the cycle. C. What is the net specific work output of the cycle? D. What is the thermal efficiency of the cycle?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

IMPORTANT: For problem solving items, start your solution by presenting the cycle in P-v and T-s diagrams. Label all points and mark the process where the heat is added and rejected. Also mark the area showing the net work of the cycle. The parameters of the initial state of one kilogram of air in the cycle of an internal combustion engine are o.095 MPa and 65 deg.C. The compression ratio is 12. Compare the values of the thermal efficiency for isobaric and isometric heat supply in the amounts of 820 kJ.
Consider an air-breathing Brayton cycle gas turbine. The compressor inlet state of the air is 302 K and 105 kPa, while the turbine inlet state is 962 Kand 1,42 MPa, What is the back work ratio for this device. expressed as a percentage to 1 decimal place? Take the specific heat c, of air to be 1.005 kJ-kgK and its specific heat ratio to be 1.4.
One kg is taken from the air during the Otto cycle, the initial pressure and temperature are 10 kN / m and 100 ° C respectively, the pressure ratio is 6: 1, and the added heat upon expansion is 3350 kJ / kg. Looking for volume pressure, temperature, thermal efficiency and work-down?
Provide a complete and logical solution for the problem. If linear interpolation is required in the problem, tabulated values is considered as a solution. Also, provide T-S or P-V diagrams for each problem. For a Rankine Cycle, steam at 5.25 MPa, 435°C expands to 0.036 MPa. For 10 kg/s of steam, determine: a. Heat added b. Heat rejected c. Work of turbine d. Thermal Efficiency
Two engines, one of the auto cycle type and the other of the diesel type, have the same compression ratio and the same amount of heat entering, which one is more efficient? Prove it with a diagram.
Fill in the blank: The compression in the Otto cycle involves an isentropic process in a closed piston-cylinder assembly, whereas the compression in the ideal Brayton cycle involves an isentropic process in a(n) (Type your answer here) operating at steady state.
On the diagram below sketch a basic Rankine cycle with superheating. Assume that there are irrevesibilities in the turbine and pump. Identify the device associate with each process. Make sure to label: the states and include important features, e.g. lines of constant temperature, volume, pressure, entropy, vapor dome, etc.
A generator uses a gas turbine cycle. Air enters the compressor at a pressure of 1 bar and a temperature of 30°C with a compressor efficiency of 0.85. Hot gas exits the combustion chamber at a pressure of 9 bar and a temperature of 900°C. The power generated by the turbine is 2400 kW with a turbine efficiency of 0.82. a. Draw installation diagrams and T-s cycle process diagramd b. Determine the work of the compressor and turbine and the mass rate of the air requirement c. Cycle thermal efficiency (air: Cp=1,005 kJ/kg. K dan γ=1.4; Gas hot: cp=1,005 kJ/kg K and γ=1.4)
1. Consider an ideal Carnot Cycle with water as the working fluid using operating conditions shown. a. Complete the following chart with relevant state properties. Turbine Temperature (°C) Entropy (kJ/kg K) Pressure Boileri State Quality (bar) Cooling water Pump Condenser 1 50 1 4 0.50 0.50 4 50 Sketch the process on a T-s diagram, including the liquid-vapor dome. How much work per kg of flow does the turbine produce, in kJ/kg? How much total work per kg of flow does the entire cycle produce, in kJ/kg? b. c. d. What is the thermal efficiency of the cycle? How would you expect that thermal efficiency to change for a Rankine cycle operating similarly, but with state 3 a saturated liquid at the same pressure, and state 4 a compressed liquid at the same pressure? Would it increase, decrease, or stay the same? Explain. e. f. 2. 31
Generic Air-standard cycle – A cycle is operating within a piston cylinder with the following processes. Draw the p-v and T-s diagram and find the cycle efficiency. 1→ 2: isentropic compression 2 → 3: constant pressure heat addition 3 → 4: isentropic expansion 4 → 1: constant volume heat removal State 1 State 2 State 3 State 4 100 kPa 2 MPa ? ? 15 °C ? 1200 °C ?
for a rankine cycle, steam at 5.25 Mpa, 435 C expands to 0.036 Mpa. for10 kg/s of steam, determine:
A 136 kg/s steam with an inlet condition of 52 bar, 400 C enters a rankine turbine and expands to 36 kPa. determine the work, the thermal efficiency, and the steam rate (a) for the cycle, (b) for the turbine. (c) With the same specifications, consider the steam expanded on an actual turbine and the brake steam rate is 4800 g/kwh and the driven electric generator has an efficiency of 0.93. Find Brake Thermal Eff, Brake Engine Eff, Combined Work, and quality or temperature of actual exhaust steam