Air at 2 bar and 40°C is heated as it flows through tube of diameter 30mm at a velocity of 10 m/s. Calculate the heat transfer per unit length of the tube when wall temperature is maintained at 100° C all along length of the tube. How much would be the bulk temperature increase over one metre length of the tube ? Use the following relation : Nu = 0.023 Re8 P4 u = 20.6 x 106 N- s/m2: Pr = 0.694 c, 1.009 kJ/kg°C; k = 0.0297 kg/m°C;

Air at 2 bar and 40°C is heated as it flows through tube of diameter 30mm at a velocity of 10 m/s. Calculate the heat transfer per unit length of the tube when wall temperature is maintained at 100° C all along length of the tube. How much would be the bulk temperature increase over one metre length of the tube ? Use the following relation : Nu = 0.023 Re8 P4 u = 20.6 x 106 N- s/m2: Pr = 0.694 c, 1.009 kJ/kg°C; k = 0.0297 kg/m°C;

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water flows in a 3.5-cm-diameter pipe so that the Reynolds number based on diameter is 2000 (laminar flow is assumed). The average bulk temperature is 10°C. What would the heat transfer coefficient be in W/m2.°C for such a system if the tube wall was subjected to a constant heat flux and the velocity and temperature profiles were completely developed? Evaluate properties at bulk temperature.
Fluid is flowing through a 20 mm inside diameter and 25 mm outside diameter brass tube at no leaking with temperature at 65℃ and length of 10 m. Surface conduction of hot fluid is 5.2W/(m^2℃) and thermal conductivity of brass is 12.84W/(m℃). Brass tube is covered by silica of 6 mm thickness with thermal conductivity of 13.84W/(m℃) . Outside of it, is a fluid with 45℃ with surface conductance of 3.2W/(m^2℃). Find the heat transfer from the hot fluid with temperature of 65℃ to fluid with temperature of 45℃.
Water going into a pipe with a tempeture of T1 and going out T2 . ambient tempeture is T0. flow rate q. Develop an expression for T2 ( based on heat transfer) Length of the pipe Lh0 - convective heat transfer coefficient of the airhW -convective heat transfer coefficient of the waterk- pipe thermal conductivity (W/m·K)d – pipe diameter Use any other varilable that you need and can be found online easily .
Determine the mean heat-transfer coefficient and the quantity of heat transferred in water flowing in a horizontal tube 3 mm in diameter (d) and 2 m long (l), if ω = 0.3 m/sec; tf = 60 deg C and tω = 20 deg C. Constants: @ tf = 60oC, λf = 0.567 kcal/m-hr-oC; νf = 0.478 x 10-6 m2/sec β = 5.11 x 10-4 1/oC and Prf = 2.98. @ tω = 20oC, Pr? = 7.02
To cool the hot oil, an engineer has suggested that the oil be pumped through a submerged pipe in a nearby lake. The pipe (external diameter = 20 cm) will be placed in the horizontal direction. The average pipe outer surface temperature is 130 °C. The temperature of the surrounding water is assumed to be constant at 10 °C. Pipe length 150 m. If it is assumed that there is no movement of water. a. Determine the convective heat transfer coefficient of the outer pipe surface to the water. =AnswerWatts/ (m² °C) b. Determine the rate of heat transfer from the pipe to the water. =AnswerkW
Hot water (cp=4.18 kJ/kg.K, m = 2.8 kg/min) flows inside a tube (inner diameter = 9 mm, Length = 93 cm, thickness = 1.0 mm, k outer surface is 204 kW/m .What is the temperature drop of water ( C)? 40 W/m.K), if the heat flux on the tube %3D tube
Heat Transfer with a Liquid Metal. The liquid metal bismuth at a flow rate of 2.00 kg/s enters a tube having an inside diameter of 35 mm at 425°C and is heated to 430°C in the tube. The tube wall is maintained at a temperature of 25°C above the liquid bulk temperature. Calculate the tube length required. The physical properties are as follows (H1): k = 15.6 W/m K, c,=149 J/kg K, u = 1.34 x 10-3 Pa s.
Engine oil flows through a 50 mm diameter tube at an average temperature of147°C. The flow velocity is 80 cm/s. Calculate the average heat transfer coefficient if the tube wall is maintained at a temperature of 200°C and it is 2 m long. Hint: Area can be assumed to be equal to the vertical projectiion of the tube , i.e. LD. Ans.: h = 377.36 W/m2.K . Draw an illustration. Note: use the formula on the picture
Water flowing at 0.1 kg/s through a thin-walled 50-mm diameter pipe is cooled from 400 K to 300 K. Calculate the required length of pipe if the outside coolant moving cross ways over the pipe is atmospheric air at 250 K moving at 20 m/s. Assume properties are: Water: (k = 0.668 W/m K, density = 974 kg/m^3, Pr = 2.29, v = 3.75*10^-7 m^2/s, C_p = 4195 J/kg K). Air: (k = 0.0263 W/m K, Pr = 0.707, v = 15.89*10^-6 m^2/s). 1. For the above problem the inside pipe heat transfer coefficient h_in=____ W/m^2 K. a) 422 b) 451 c) 185 d) 493 e) 79 2. For the above problem the outside pipe heat transfer coefficient h_out=____W/m^2 K. a) 126 b) 55 c) 238 d) 83 e) 326
A Figure illustrates the tube-flow system. The heat transfer under developed flow conditions when the flow remains laminar. The wall temperature is Tw, the center of the tube temperature is Te the radius of the tube is re, and the velocity at the center of the tube is uo. The velocity distribution equation is: 1 uo Prove that: 1 aT uor. T - T= a ax 4 ro Start the solution of the equation : P{żar drjuc,T 1 a ()- aT 1 әт ur дr ar « дх
Water going into a pipe with a tempeture of T1 and going out T2 . ambient tempeture is T0. Develop an expression for T2 ( based on heat transfer) Length of the pipe Lh0 - convective heat transfer coefficient of the airhW -convective heat transfer coefficient of the waterk- pipe thermal conductivity (W/m·K)d – pipe diameter Use any other varilable that you need and can be found online easily .
Consider a pipe of 5 m in length and 1 cm in diameter. Temperature difference between the wall and the fluid (k = 1 W/mK) at exit is 25% that of at inlet. If the pipe wall temperature remains as constant of 80 ºC, total heat transfer rate 1000 W, and the flow is laminar what is the fluid temperature at inlet?