After running the lab, you select an analysis point with the following properties: Atmospheric Pressure: 14.7 psia Compressor Inlet Pressure: 0.02 psig Compressor Exit Pressure: 7.24 psig • Turbine 1 Inlet Pressure: 7.42 psig • Turbine 1 Exit Pressure: 0.41 psig ● Compressor Inlet Temperature: 20.4°C Compressor Exit Temperature: 145.14°C • Turbine 1 Inlet Temperature: 532.9°C • Turbine 1 Exit Temperature: 488.48°C • Fuel Flow: 10.26 L/hr Engine RPM: 47,222 What is the velocity at the compressor inlet (m/s)? Your Answer: Answer

After running the lab, you select an analysis point with the following properties: Atmospheric Pressure: 14.7 psia Compressor Inlet Pressure: 0.02 psig Compressor Exit Pressure: 7.24 psig • Turbine 1 Inlet Pressure: 7.42 psig • Turbine 1 Exit Pressure: 0.41 psig ● Compressor Inlet Temperature: 20.4°C Compressor Exit Temperature: 145.14°C • Turbine 1 Inlet Temperature: 532.9°C • Turbine 1 Exit Temperature: 488.48°C • Fuel Flow: 10.26 L/hr Engine RPM: 47,222 What is the velocity at the compressor inlet (m/s)? Your Answer: Answer

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Directions: Identify whether each statement is True or False. 1.When Dealing with liquids and gases, we ordinarily speak of stresses, for solids we speak pressures True False 2 .Open system is defined when a particular quantity of matter is under study. This system always contains the same matter. There can be no transfer of mass across it`s boundary True False 3. Thermodynamic properties can be placed in two general classes control volume and intensive True Flase 4. Triple point of water- is the condition of water temperature and pressure under which gaseous liquid and solid phases cannot exist in equilibrium True False 5. Intensive properties are additive in the sense previously considered. Their values are dependent of the size of extent of system and may vary from place to place within the system at any moment. Specific volume pressure. and temperature are important intensive properties True False
3. At a load of 43,000 KW in a steam turbine generating set, 3600 RPM, the following data appear in the log sheet. Steam flow -190 Metric Tons/hour Steam pressure - 8.93 MPaa Steam temperature - 535C Feed-water temperature - 230 C Fuel Flow: Bunker Oil -3.4 Metric Tons/hr HHV=10,000 Kcal/hr Local coal -18 Metric Tons/hr HHV = 5350 Kcal/hr Determine the overall boiler efficiency. h at 8.93 MPa and 535°C -3475.7 KJ/kg hf at 230°C-990.12 KJ/kg
Definition, diagrams, equations, & sample problems 合 Test Your Skills 14.1 2. A substance undergoes a polytropic process where n = 1.4. If the final pressure is twice as large as the initial pressure and the initial temperature is 264 K, find the final temperature in K. Your answer
QUESTION 18 Describe the T-s diagrams accordingly by filling it the blanks accordingly. Use the sets of words given below for correct description. Ideal / Actual / vapour /cycle /Carnot/ Rankine/ Diesel/Otto/ Brayton/Ericsson/Stirlin g/regenerative/ reheat/ closed open/with/a Wurbout 9in A B P= constant 9in V= constant (b) T-s diagram D 4s 4a G Yout v=const. 9in v=const. E H Yout Yout Wpumpin High-pressure turbine C F Reheating I 4 3 Low-pressure turbine
1- The following observations were recorded during a test on a steam condenser of counter flow: Barometer reading = 765 mmHg Vacuum reading = 710 mmHg Steam and air temperature = 35 •C Condensate temperature = 28 •C Condensate collected per hour = 2 tons Cooling water collected per hour = 60 tons Inlet cooling water temperature = 10 •C Exit cooling water temperature = 25 •C Cooling water tubes specification = Thin tubes D=2 cm ,L=5 m ,n=350, Determine: a- The vacuum efficiency. b- The condenser efficiency. c- Quality of steam x entering the condenser.
Item 10 A house is heated and maintained at 20 °C by a heat pump. Part A Determine the maximum possible COP if heat is extracted from the outside atmosphere at (a) 10 °C, (b) 0 °C, (c) –10 °C, and (d) -40 °C. Express each COP numerically to three significant figures, separated by commas. ΑΣφ vec COP10 °C, COP, oc, COP 10 °c, COP 40 °c = Submit Request Answer
Course: ThermoDynamics 1
Question 11 A 4 stroke gasoline reciprocating internal combustion engine operating stoichiometrically in an environment at standard temperature and pressure consumes 0.8 kilograms of fuel per hour and it has a displacement of 0.77 litres. The engine speed is 2,714 revolutions per minute. Assume the ambient air density is 1.2 kg/m3. What is the volumetric efficiency of the engine. Enter your answer as a rounded percentage. e.g., if the volumetric efficiency is 63.6%, enter the number 64.
View Policies Current Attempt in Progress A High-Performance Engine. You and your team are tasked with evaluating the parameters of a high-performance engine. The engine compresses the fuel-air mixture in the cylinder to make it ignite rather than igniting it with a spark plug (this is how diesel engines operate). You are given the compression ratio for the cylinders in the engine, which is the ratio of the initial volume of the cylinder (before the piston compresses the gas) to the final volume of the cylinder (after the gas is compressed): VV, Assume that the fuel-gas mixture enters the cylinder at a temperature of 26.0 °C, and that the gas behaves like an ideal gas with y-7/5. (a) If the compression ratio is 14.9:1, what is the final temperature of the gas if the compression is adiabatic? (b) With everything else the same as in (a). what is the final temperature of the gas if the compression ratio is increased to 16.117 (c) Everything else being the same, for which compression ratio…
Problem 2 An Air Force Research Lab engineer is asked to evaluate the maximum theoretical work that could be produced by the first stage turbine section of an experimental jet engine. Test stand measurements provide the following information: a. Entering air conditions: 1400 K, 8 bar b. Exiting air conditions: .8 bar Part 1: Since you don't have a mass flow rate measurement, what will be the units will you report maximum theoretical work in? Part 2: Write the first law equation for your control volume showing all terms. What assumptions will you make to simplify the equation. Part 3: Pin down the outlet state on a notional T-s diagram for air (just show the two isobars). Why did you select this point? Part 4: What assumption about the properties of air will you make in order to solve this problem? Part 5: Use the appropriate form of the 'Tds' equation and the air tables to solve for the exit state. Part 6: Calculate the max theoretical work
Read the questions carefully before answering. Box or indicate your final answers when solving and draw your diagrams cleanly. Use the steam tables provided and DO NOT ROUND the values from the steam table. Write down the values taken from the steam table. Steam undergoes an Isentropic process where it is initially at 1.30MPa and200C then it expands to a pressure of 0.75MPa, thus becoming wet steam. What is the dryness of the steam and the change in enthalpy for the process?
Water leaves the safety valve of a boiler at a velocity of 100 ft/sec. What is the gauge pressure in the boiler? * 5154 Ib/ft? 9700 Ib/ft2 19400 Ib/ft2 75100 Ib/ft2 What is the specific heat of a metal substance if 135 KJ of heat is needed to raise 5.1 kg of the metal from 18 °C to 31.5 °C ? * 1630 J/kg °C 1922 J/kg °C O 1961 J/kg °c O 1554 J/kg °C