According to the table, determine a) the most rigid material, b) the most ductile material, c) the most brittle material, d) the material with the lowest strength. Elastic Yield Strength Tensile Strength Elongation (%) Material Modulus (MPa) (MPa) (GPa) No 1 110 140 42 250 No 2 160 160 32 200 No 3 310 210 10 400 No 4 410 200 12 450 No. 5 360 220 36 225

According to the table, determine a) the most rigid material, b) the most ductile material, c) the most brittle material, d) the material with the lowest strength. Elastic Yield Strength Tensile Strength Elongation (%) Material Modulus (MPa) (MPa) (GPa) No 1 110 140 42 250 No 2 160 160 32 200 No 3 310 210 10 400 No 4 410 200 12 450 No. 5 360 220 36 225

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Ql- mm ,length 40 mm. The final diameter 18 mm and length 45 mm. Draw the force-extension diagram and determine the following : a) Ultimate tensile strength, c) Modulus of elasticity, d) Percent elongation and e) Percent reduction in area. The following data collected from tensile test of a metal bar diameter 20 b) The fracture strength, Force - kN 75 90 | 105 120 131 125 110 25 50 4.7 Extension-mm 0.02 0.04 0.06 0.20 - 0.60 1.60 3.00 4.0 Fracture
Read the question carefully and give me both A&B right solutions otherwise leave it. A) Steel Alloy rod made of Stainless Steel 304 is subjected to 60 kip of Tensile force. Steel rod is having diameter of 1 in. and Length of 8 in. Determine change in its length and diameter. Consider material behaves elastically. For determining material properties use Mechanical property table. B) An aluminium specimen made up of 6061-T6 Material has a diameter of d = 20 mm and a gage length of L0= 300 mm. If a force of 135 kN elongates the gage length 0.9 mm, determine the modulus of elasticity. Also, determine contraction of diameter.
a)Define the following mechanical properties which can be derived and, in each case, state the appropriate unit. i)Engineering stressii)Yield stress leveliii)Young’s modulusIv) Ultimate tensile stressv)Ductilityvi) Toughness B) Briefly describe a standard test method which can be used to establish properties (ii), (iii) and (iv) mentioned in part (a) of this question. Also provide a sketch of the apparatus.
Based upon the information in the table below, which material is the stiffest? Elastic Strain at Fracture Fracture Yield Strength (MPa) Tensile Modulus Strength (MPa) 120 550 340 Fractures before yielding 850 Strength (MPa) 105 500 265 650 720 Material 100 415 310 0.40 0.15 0.23 (GPa) 150 310 210 350 210 700 0.14 OE OB A. OD
The engineering stress-strain curve below was obtained for a precipitation hardened Aluminum alloy. What is the approximate Yield Strength for this alloy in psi? Engineering Stress Based on Original Area (psi) 50,000 45,000 40,000 35,000 30,000 25,000 20,000 15,000 10,000 5,000 0 O 0.02 0.04 0.06 Aluminum 6061-T6 0.08 0.1 0.12 Engineering Strain (in/in) 0.14 X 0.16 0.18
Which one(s) of the following about G, shear modulus of elasticity of a material are correct? select all which are correct. G is also called the modules of rigidity. G is related to the modulus of elasticity E and Poisson’s ratio . G is usually smaller than Young's modulus E for the same material. G is the ratio of shear stress to shear strain when the material's proportional limit in shear has not been exceeded.
hings The following results were obtained during a tensile test to destruction on a mild steel test piece of diameter 15.96mm and 80mm gauge length Extension for a load of 40KN = 0.08mm Maximum load applied during test = 93kN Diameter at fracture = 12.85mm %3D Final length between gauge points 106mm From these results, determine: i) The modulus of elasticity for mild steel ii) The tensile strength iii) Percentage of elongation iv) Percentage of reduction in area
BM Strength of Materials Dr. Maad Abdullah Hussein AL-ESRAA UNIVERSITY COLLEGE 8. BRINELL TEST Load (P) Kg Material Diameter of Ball Impression Diameter (mm) No. Brinell Hardness, HB (mm) 1 Iron 2.5 0.65 187.5 Соpper 2.5 0.74 62.5 3 Aluminum 2.5 1.06 31.25 9. THE VICKERS TEST Impression Diameter (mm) d average Vickers Hardness, No. Material Load (P) Kg di d2 HV 1 Iron 0.58 0.65 50 2 Сopper 0.72 0.76 30 3 Aluminum 0.94 0.86 30
Determine the percentage of ductility of a metal alloy having the following tensile stress-strain diagram. 600 500E 400 500 300 400E 300 200 200 100 100 0.000 0.002 0.004 0.006 Strain 0.00 0.04 0.08 0.12 0.16 0.20 Strain EN Stress (MPa) Stress (MPa)
250 Stress (MPa) 200 150 100 50 0.10 Q3. Using Figure 2 determine the: A). 0.2% offset yield strength B). Ultimate Stress Stress (MPa) 150 100 50 0.20 Strain Figure 2 Strain 0.005 0.30 C). Using Figure 2, determine the sample length at fracture, if the initial length was 10 cm. 0.40
Q3 : Rank the magnitudes of the moduli of elasticity for the following hypothetical X, Y, and Z materials from the greatest to the least.The appropriate A, B, and n parameters for these three materials are tabulated below; they yield EN in units of electron volts and r in nanometers: Material A В n 2.5 2.0 x 10-5 8. Y 2.3 8.0 x 10-6 10.5 Z 3.0 1.5 x 10-5 9.
Determine the percentage of ductility of a metal alloy having the following tensile stress-strain diagram. Stress-Strain Diagram 1200 1000 800 1000 600 800 600 400 400 200 200 0.00s 0.01 0.015 0.02 0.025 0.03 0.05 0.1 0.15 0.2 025 Strain (mm/mm) Select one: O 0.2% O 19% 3% 25% 0.5% Stress (Mpa)