AC7 x 9.8 tension member is connected to a thick gusset plate as shown in Figure (2). Both the member and the gusset plate are A36 steel. Compute the available block shear strength of the tension member.

AC7 x 9.8 tension member is connected to a thick gusset plate as shown in Figure (2). Both the member and the gusset plate are A36 steel. Compute the available block shear strength of the tension member.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter3: Tension Members

Section: Chapter Questions

Problem 3.5.1P

See similar textbooks

Related questions

Q: Explain how the functional characteristics and design selection criteria are informed by proposed…

A: OPERATING/FUNCTIONAL FEATURES OF THE PROPOSED BUILDING - 1. The proposed structure should be strong…

Q: Explain what is meant by temperature and give examples of itsimportant role in engineering analysis…

A: Temperature is indeed a measurement of the amount energy of the atoms and molecules inside a…

Q: START (FINISH SUMMARY ACTIVITY/DURATION ES EF LS LF FF TF A-12DAYS B-24 C-60 D-36 E-24 F=30 G-42…

Q: Identify two type of strains that have been used in order to assess pavement performance. O Linear…

Q: st unit weight o sture content is of the soil solids

Q: Mechanics of Deformable Bodies A simply supported beam of length L has a rectangular cross section…

A: Given: Simply supported beam Concentrated load at centre Span To find: fbmax/ tmax Notations :…

Q: 1- The moment of inertia of a rectangular section 3 cm wide and 4 cm deep about X-X axis through…

A: Moment of inertia of rectangular section 3 cm wide and 4 cm deep; Answer C.16 cm4 Ix=∬y2dxdyIy =…

Q: Question number (15) Highway Engineering civil engineering

Q: A shaft is subjected to torsional moments as shown in figure. Plot the torsional 3 kN-m 5 kN-m E…

Q: 2- A force acting on a body may A. Change its motion C. Retard its motion B. Balance the other…

A: When a Force acting on a body :- Change its position :- When a force acting on a body it may move…

Q: Create your own Workplace Housekeeping Inspection Checklist for a NETWORK /CABLE Company with the…

A: Checklist for a CABLE Company Floors and Other Areas Are floors clean and clear of waste? Are…

Q: If the height of moist fine sand in a measuring cylinder is 10.5 cm and the height reduces when it…

A: given initial height of sand h1=10.5 cmreduced height of sand h2=8.2 cm

Q: An installer finds that it takes 5 minutes to cut out a duct. It then takes 4minutes to bend the…

A: Given:- 5 minutes to cut out a duct It then takes 4 minutes to bend the metal and 7 minutes to lap…

Q: Assuming the data given in the following table, calculate turbulence effect in horizontal well for…

A: Solution- ln (y-33) =6 t y -33 = e6t y=e6t +33

Q: Question 9 Nota Pout of L00 The bolt in the figure below has a diameter of 0.75" inch. If the load P…

A: step 1-

Q: 3- The force induced in the string AB due to the load W, as shown in the figure is:

A: External Force W acting downford direction at point B so forced are developed due to this load W.

Q: What are the points of convergence and divergence in the approaches to waste management of two…

A: Plastic waste management in China The increase in the plastic waste in China lead to provide…

Q: hway Engineering civil engineering

A: We know Degree of compaction is given by R=Compacted SGExperimented SG

Q: Find the equivalent shear in beam of width 350 mm and effective dept 600 mm, Given data: Factored…

A: Given data- width of beam b=350 mmeffective depth=600 mmfactored shear force V=150 kNTorsional…

Q: Q1/ A traffic engineer urgently needs to determine the AADT on an urban minor arterial highway; he…

Q: In reference to the figure below, if us = 0.2 at the rear drive wheels B of the 1.5 Mg vehicle with…

A: The entire load of the car will get transferred through the front and rear wheel pair. And…

Q: 1. The angular momentum equation becomes ΣM = E(rxV)pV. A if the convective term of the angular…

Q: Q.12. The velocity distribution in the boundary layer is given by: U 3 1 n² η FORDE V y In which n=…

Q: /Abridge has been in use for twelve years at the following conditions: 1- during the first two years…

A: The given data is shown below: Amplitude stress, cars=108 cyclesAmplitude stress,lorries=106 cycles

Q: Two forces are acting at an angle of 120°. The bigger force is 40 N and the resu the smaller one.…

A: To find the smaller force (F1)-

Q: > determine the moment of inertia with respect to A-A axis for the shaded area shown in the figures.…

Q: Using the slope-deflection method, determine the end moments and the reactions at the supports of…

A: Given data E = 200 GPA = 2 × 105 N/mm2 I = 213 × 106 mm4 EI = 2 × 105 × 213 × 106 EI = 426 × 1011…

Q: Q- Depth of the root zone=1.8 m Existing moisture=8% Dry density of soil-1450 kg/m³ Quantity of…

Q: Q2: In the sewage pipe project, the readings of the ruler from left to right were as follows: 0.680,…

A: Given data in question Staff reading Elevation of 1st point To find out Elevations and check Note…

Q: Q2: In the sewage pipe project, the readings of the ruler from left to right were as follows: 0.680,…

A: Given data: 0.68, 1.455, 1.855, 2.330, 2.885, 3.380, 1.055, 1.860, 2.265, 3.540, 0.835, 0.945.…

Q: A rectangular pretensioned beam has concentric prestress force of 1000 KN. The beam is 300 x 50 mm…

Q: › determine the moment of inertia with respect to A-A axis for the shaded area shown in the figures.…

Q: A pump can lift water at a discharge of 0.15m/s to a head of 25 m. The critical cavitation number…

A: Given:discharge, Q=0.15 m3/shead, h=25 mcavitation number, σc=0.144Barometric pressure=9.8 m of…

Q: The rectangular wood beam is loaded as shown in the figure. Determine the largest allowable…

A: given: shear stress = 1.2 mpa working stress = 10 mpa From equilibrium, Ra + Rc = 24 + P taking…

Q: Consider a point in a structural member that is subjected to plane stress. Normal and shear stress…

Q: Give examples of engineering variables that are based on the fundamental dimensions of length and…

A: Although all technical issues require the use of units, measurements and units are frequently…

Q: 5.21 Determine the amount of reinforcing steel required for each T beam in the accompanying…

A: 1. Span4 = 204 = 5 ft = 5 × 12 = 60 inches 2. beff = bw + 16 × hf beff = 12 + 16 (4) = 76 inches…

Q: Each standard axle consists of 2 tyres. O True O False

A: To Determine Whether the given statement is true or false.

Q: At a point in a machine component that is subjected to plane stress, the normal and shear stresses…

Q: QUESTION 2 Determine the force in members CE, CD and AD and state whether the members are in tension…

Q: Rainfall of magnitude 4 cm, 4 cm and 2 cm occurring on three consecutive 2-hrs durations on a…

A: Given Data Time in hrs. 0-2 2-4 4-6 P in cm 4cm 4cm 2cm Catchment area is given as 45 Km2 We…

Q: 1. Following are the relationships of e and o' for a clay soil: e o' (kN/m²) 1 20 0.97 50 0.85 180…

A: The given data is shown below: H=1.37mσo=70 kN/m2σ'o+∆σ'=200 kN/m2

Q: acceleration at a ind the ratio of th

Q: Find the minimum size of the gravel that will not move in the bed of a wide rectangular channel of…

A: given wide rectangular channeldepth y=1.5 mslope S=0.003

Q: 1. A wire rope is used with total load of 8500 kg and bending load of 55,000kg. If the breaking…

A: Given, Total load (Ft) = 8500 kg Bending load (Fb) = 55000 kg Breaking strength (Fu) = 1,20,000 kg

Q: Point A B C D E X(m) 0 + 170 +470 + 340 - 40 Y(m) 0 + 320 +90 - 110 - 22

A: solution Use cross coordinate method to find the area of the traverse cross coordiantes are…

Q: Questions 9. An RCC slab (M 25 grade) of dimensions 5 mx 5 mx 0.15 m, is supported on four square…

Q: A reservoir with a live storage of 300 million cubic metre irrigates 40000 hectares (1 hectare=10000…

Q: O For a flow of 5.7 MLD and a detention of 2 hour, what is the surface area of a rectangular…

A: Given data, Flow rate for rectangular sedimentation tank, Q= 5.7 MLD = 5.7×10³m³/day Detention…

Q: Draw the profile for the point below: Distance (m) 0 22 30 45 60 78 85 91 125 150 Elevation (m)…

A: To Determine Draw the Elevation from from the given distances and the elevation at those distance…

Concept explainers

Mechanics of Solids

It is the study of the behavior of solid materials, their characteristics under various circumstances such as variation in external forces, temperature, and other internal factors. It is one of most important study in the field of engineering science, especially chemistry and mechanical engineering. In rigid body, the idealization of the solid body in which deformation is neglected. Deformation is known as the force acting on the solid state system which exerts change in its shape of the body but it continues to be at rest or in a uniform motion but it cannot accelerate. But those solid systems do have elasticity, compressibility and can be bent. This field is very vast since there are wide range of materials around us.

Question

AC7 x 9.8 tension member is connected to a thick gusset plate as shown in Figure (2). Both the
member and the gusset plate are A36 steel. Compute the available block shear strength of the
tension member.
3"
C7x9.8
O
O
O
O
O
"-diameter bolts

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The following image shows a front and side view of the column connection. The bolts have a diameter of ¾”. The W12X65 profile has a thickness of 0.605”. Determine: a. The shear stress in the bolts. Answ. 11.81 ksi b. The axial stress in the bolts. Answ. 23.62 ksi c. The support stress in the W12X65 profile. 11.50 ksi
Determine the LRFD design strength and the ASD allowable strength. Neglect block shear. A36 steel and 7/8-in Ø bolts N VA N SZ 2-MC 12 x 40 00 K All 2 in 2 in 3-in 3/in 2/in
2 hEe c W@ B & - For the beam shown find the value of Force (F) Ib and maximum stress due to flexure ( oy ) psi if the shear force in bolts is 300Ib and the shear stress in beam 120psi. Spacing between bolts (S) =5in F T —————————————+% 4ft 8ft 1in 1in -~ - 10in 1n § 8in
For the connection shown, determine the average shear stress produced in the 3/8- in. diameter bolts if the applied load is P = 2,500 lb. %3D O 5606 psi O 6559 psi O 2219 psi 6506 psi 5660 psi 1200 psi
6) Calculate the shear lag reduction factor, u, for the spliced W-shape tension member shown. Hint: you can treat the wide flange section like two WT6x25s. | W12x50 H THE 3" 3" Typical Splice Plate TH HHHH -Splice Plate W12x50
Problem # 8.0 The tension member shown is a C12 x 20.7 of A572 Grade 50 steel. Will it safely support a service dead load of 60 kips and a service live load of 125 kips? Use Equation 3.1 for U. by O O 2½" 22" | 2½" 7/8-in.-diameter bolts. оооо оооо m 000 U=0.90 Single and double angles m W10x 19 = 0.394 (for parent shape) 0000 by Single and double angles … W8 x 24 -=0.820 > U=0.90 O O O 00 U=0.80 W shape U=0.70
Considering the following steel connection. The plates in Pink are 9mm steel plates. The middle plate (Yellow) is 18mm thick. The width of the plate is 100mm. The maximum allowable tension stresses on any of the plates is 100Mpa in Gross Area Yielding and 150 Mpa for Net Area or Tension Rupture. The bolts used are 8mm in diameter, the holes are 10mm in diameter, no need to add 1.6mm. The bolts allow a maximum of 280 Mpa of shear. Determine the maximum allowable "P" of the connection in kN.
A C8x11.5 single channel section us bolted to a gusset plate with M22 bolts. Assume A36 steel, 5.6 mm thick web for the channel and an 8mm gusset plate. U=0.80 The channel has a gross area of 2181 mm^2. The bolts have a shear stress of 457 Mpa. What is the design tensile strength due to gross yielding (kN)?
= 410 N/mm? 8.20 A column section ISHB 300 @ 618 N/m (f, mand f, = 250 N/mm") is to be spliced. The factored design loads are: %3D Axial load over the column 450 kN Shear force 100 kN Bending moment (a) Design the splice plates and bolted connections using bolts of grade 4.6. (b) Design HSFG bolts and revise the splice plate size if possible. 30 kNm
The link shown is 9,25 in. Thick, and has a single Shear Pin connection. what is most nearly the required diameter (in) of the Pinif (tis average allowable shear Stress is 12ksi? 4 2in 20ksi
The following image shows a front and side view of the column connection. The bolts have a diameter of ¾”. The W12X65 profile has a thickness of 0.605”. Determine:a. The shear stress in the bolts.b. The axial stress in the bolts.c. The support stress in the W12X65 profile.
(See Attached picture of truss) 2. Since the reaction force at point A is 8975 #, The reaction force at point H is 7625#, the stress force in member AB is 14262 # (C), and the stress force in member BC is 11083# (T); calculate the minimum steel bolt size for attachment at points A and H. Use a factor of safety of 1.5 and a fitting factor of 1.15