a. Determine the bias current, /BIAS, given that the input currents to an op- amp are and 7,9 mA, 8.3 mA. b. Compare a practical op-amp to an ideal op-amp. c. Determine the input and output impedances for amplifier configuration in Figure 2.

a. Determine the bias current, /BIAS, given that the input currents to an op- amp are and 7,9 mA, 8.3 mA. b. Compare a practical op-amp to an ideal op-amp. c. Determine the input and output impedances for amplifier configuration in Figure 2.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1- Mention any two advantages of Integrated Circuit . 2- For the circuit given below : Vin is a sine wave Vinpp=6 V and Vref=-2.4 V , Assume Vsat=±12V Name the circuit and draw the input and output waveforms . Vin Vref 3- Explain why open-loop op-amp configurations are not used in linear applications? Draw the block diagram of opamp and define the function of each block
If the ideal design for op-Amp circuit generate 200 mV at the output, Then practically with 26 mV offset voltage the output voltage of the circuit will be equal to .............. mV
One way to measure the slew-rate limitation of an op amp is to apply a sine wave (or square wave) as the input to an amplifier and then increase the frequency until the output waveform becomes triangular. Suppose that a 1-MHz input signal produces a triangular output waveform having a peak-to-peak amplitude of 4 V. Determine the slew rate of the op amp.
1) Op-amp limiting factors - Current Saturation U2 Vin R1 OUT OPAMP R2 RLoad The saturation output current for the above op-amp is +/- 15mA. For the following input signals, determine if the output appears as would be expected in an ideal circuit. Include sketches of the output voltage. a) R1 = 100, R2 = 900, an open circuit load, and Vin is 2Vpp triangle wave with zero offset voltage (Vmax 1V, Vmin = -1V) and a period of 2ms. b) R1 = 100, R2 = 900, a 1k load, and Vin is 2Vpp triangle wave with a 1V offset voltage (Vmax=2V, Vmin = 0V) and a period of 2ms. c) R1 = 100, R2 = 900, an open circuit load, and Vin is 4Vpp triangle wave with zero offset voltage (Vmax=2V, Vmin = -2V) and a period of 2ms.
Consider the following circuit using diode and Op-Amp. Assume ideal Op-Amp with output saturation at +-13V. Assume diode forward drop is 0.7V. a. Find Vo and VA when Vin = 1V and 3V. b. Find V, and VA when Vin = -1V and -3V. R Vin R VA ovo ER₂
Can you please explain and answer: Assume the opamp is power by -12V and +15V. What is the range of values for vs that does not saturateand the opamp remains in the linear region of operation?
An op-amp has a slew rate of 0.8 V/us. What is the maximum amplitude of undistorted sine wave that the op-amp can produce at a frequency of 40 kHz? What is the maximum frequency of the sine wave that op-amp can reproduce if the amplitude is 3 V?
1- Mention any two non linear applications of op- amp. 2- For the circuit given below : Vin is a sine wave Vinpp=9 V and Vref=2.4 V , Assume Vsat=±12V Name the circuit and draw the input and output waveforms . Vo Vin Vref 3- Explain why open-loop op-amp configurations are not used in linear applications? Draw the block diagram of opamp and define the function of each block
2. b) (i) Derive an expression for the differentiator using op-amp. (ii) Design a circuit to perform differentiation of an input signal that varies in frequency from 20HZ to about 2 KHz. (iii) If a sine wave of 0.5 V peak at 2 KHz is applied to the differentiator of part (ii), draw the output waveform.
You are hired as a technical consultant to model, design and analyze an efficient DC-DC buck converter for a solar PV battery charger as shown in the below figure. PV DC-DC Battery system Converter | MPPT algorithm Charge controller Given the following specifications for the design and analysis of a DC-DC Buck Converter: An input voltage of 15V < Vin < 20V and an output of Vout = 10V over a load range of 5w < Pout < 200W. Switching frequency is few = 500kHz. a) Design the inductor (L) and capacitor (C). The current ripple AiL should be below 5% of the average inductor current IL at the maximum load. The steady state ripple AVout is below 0.5 % of the steady-state value of the output voltage. For the designed L, find the value of Iout,crit at the boundary of DCM and CCM and then Plot Iout,crit vs. Vin . b) Design the rated values for switch, diode, and capacitor. Research and determine a manufacturer part number for your switch, diode, and capacitor. Provide data sheets for each. c)…
a. b. C. There is a dc-dc converter that provides isolation between input and output current. Identify the converter type and describe the operation. Draw the equivalent circuit to support the explanation. Assume the converter operates in continuous-current mode. Explain why a switched -mode dc-dc converter is better that a linear regulator. As an electrical engineer, you are required to design a chopper circuit with an output voltage of 10 V from a 30 V input with switching frequency of 50 kHz. The circuit is operated in continuous current, and output ripple voltage is less than 0.8% with resistance load of 30 Q. Assume the inductor value is 50 % larger than Lmin and assume ideal components for this design. Identify the chopper type and construct the circuit with IGBT as the power switching.
H: Design OP-Amp eircwt that Poduce an out Put an given by Uo = - ( 4 V,t Uz to.l U3) If u, = 2 sinwt = 5 V and U3 = - 100V sketch the ont Put vo ltage waveform ?