A wood beam reinforced by an aluminum channel section is shown in the figure. 150 mm 232 mm 38 mm 6.5 mm 163 mm The beam has a cross section of dimensions 150 mm x 232 mm, and the channel has a uniform thickness of 6.5 mm. If the allowable stresses in the wood and aluminum are 8 MPa and 46 MPa, respectively, and if their moduli of elasticity are in the ratio 1 to 6, what is the maximum allowable bending moment for the beam? Enter the magnitude in kN- m. (Assume that the component parts of the beam are securely bonded by adhesives or connected by fasteners. Also, be sure to use the transformed-section method in the solution.) kN- m

A wood beam reinforced by an aluminum channel section is shown in the figure. 150 mm 232 mm 38 mm 6.5 mm 163 mm The beam has a cross section of dimensions 150 mm x 232 mm, and the channel has a uniform thickness of 6.5 mm. If the allowable stresses in the wood and aluminum are 8 MPa and 46 MPa, respectively, and if their moduli of elasticity are in the ratio 1 to 6, what is the maximum allowable bending moment for the beam? Enter the magnitude in kN- m. (Assume that the component parts of the beam are securely bonded by adhesives or connected by fasteners. Also, be sure to use the transformed-section method in the solution.) kN- m

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter8: Engineering Materials

Section: Chapter Questions

Problem 7ETSQ

See similar textbooks

Similar questions

A wood beam reinforced by an aluminum channel section is shown in the figure. 150 mm 230 mm 38 mm 6.5 mm -163 mm- The beam has a cross section of dimensions 150 mm x 230 mm, and the channel has a uniform thickness of 6.5 mm. If the allowable stresses in the wood and aluminum are 8 MPa and 50 MPa, respectively, and if their moduli of elasticity are in the ratio 1 to 6, what is the maximum allowable bending moment for the beam? Enter the magnitude in kN · m. (Assume that the component parts of the beam are securely bonded by adhesives or connected by fasteners. Also, be sure to use the transformed-section method in the solution.) (No Response) 14.06 kN· m
A bar having the cross section shown has been formed by securely bonding brass and aluminum stock. Using the data given in the table, determine the largest permissible bending moment when the composite bar is bent about a horizontal axis. Take x = 32 mm. Modalus of elasticity Allowable stress Aluminum Brass Aluminum 70 GPa 100 MPa 10 mm 10 mm Brass 105 GPa 160 MPa 10 mm mm 10 mm The largest permissible bending moment when the composite bar is bent about a horizontal axis is [ kN-m.
What is the value of reduction factor of the beam, if the stress in the steel is 400 MPa, and the Modulus of Elasticity of the Steel is 200,000 MPa. O 0.671 0.692 O 0.660 O 0.650 None of the Choices O 0.681
3.* Figure 3 shows a tapered glued joint between two pieces of wood subjected to a tensile force. If the glue can sustain a maximum average tensile stress of 30 MPa and/or a maximum average shear stress of 50 MPa, what is the maximum angle that will permit the joint to transmit a tensile force F = 25 kN with a safety factor of 3.0? [Ans: 23⁰] F 1.6 A 3.4 Ө all dimensions in cm F
A flat bar of aluminum alloy 25 mm wide and 5 mm thick is placed between two steel bars each 25 mm wide and 10 mm thick to form a composite bar 25 mm x 25 mm as shown. The three bars are fastened together at their ends when the temperature is 15℃. Find the stress in each of the materials when the temperature of the whole assembly is raised to 55 ℃.Steel: Es = 200 GPa; Coefficient of expansion = 1.2x10^-5/℃.Aluminum: Eal = 200/3 GPa; Coefficient of expansion = 2.3x10-5/℃.
A composite beam made of steel and bronze has the cross section shown. The cross-sectional dimensions are b1 = 0.5 in, b2 = 1.5 in., and d = 1.0 in. The elastic modulus of the steel is E1 = 30,000 ksi, and its allowable bending stress is 24 ksi. The elastic modulus of the bronze is E, = 15,000 ksi, and its allowable bending stress is 16 ksi. Calculate the magnitude of the allowable bending moment that can be applied about the z centroidal axis. y Bronze (2) Steel (1) bị b2 Answer: M = i Ib-in. Save for Later Attempts: 0 of 1 used Submit Answer
Compute the value the shear modulus G of steel whose modulus of elasticity E is 200 GPa and poisson's ratio is 0.30.
A bar having the cross section shown has been formed by securely bonding brass and aluminum stock. Using the data given in the table, determine the largest permissible bending moment when the composite bar is bent about a vertical axis. Take x = 30 mm. Modulus of elasticity Allowable stress Aluminum Aluminum 70 GPa 100 MPa 10 mm Brass- 10 mm 40 mm- Brass 105 GPa 160 MPa 10 mm X 10 mm t The largest permissible bending moment when the composite bar is bent about a vertical axis is 1.689 kN-m.
A bar having the cross section shown has been formed by securely bonding brass and aluminum stock. Using the data given in the table, determine the largest permissible bending moment when the composite bar is bent about a vertical axis. Take x = 30 mm. Modulus of elasticity Allowable stress Aluminum Brass Aluminum 70 GPa 100 MPa 10 mm 10 mm 40 mm- Brass 105 GPa 160 MPa 10 mm X 10 mm The largest permissible bending moment when the composite bar is bent about a vertical axis is 1.689 kN.m.
1. Three metal strips, each 40 mm height, are bonded together to form the composite beam shown. The modulus of elasticity is 210 GPa for the steel, 105 GPa for the brass, and 70 GPa for the aluminium. If the allowable bending stress for the aluminum (Gallow)al= 100 MPa, for the steel (Gallow)s=150 MPa and (Gallow)b= 200 MPa for brass determine the maximum allowable intensit of w of the uniform distributed load. 2w Aluminum 2w 10 mm Brass 10 mm Steel 20 mm 2m - 40 mm
The wood beam has a cross section shown in figure. Determine the magnitude and location of the maximum tensile and compressive stress acting on the beam.
A composite bar is fabricated by brazing aluminum alloy [E = 10,000 ksi] bars (1) to a center brass [E = 17,000 ksi] bar (2) as shown in the fıgure. Assume d = 0.65 in., a = 0.1835 in., L = 22 in. If the total axial force carried by the two aluminum bars must equal the axial force carried by the brass bar, calculate the thickness b required for brass bar (2). Brass (2) Aluminum (1) (1) P a b = i in.