A wide-flange shape column AB carries a centric load P of magnitude 60 kN. Cables BC and BD are taut and prevent motion of Point B in the xz plane. Using Euler's formula and a factor of safety of 2.2, and neglecting the tension in the cables, determine the maximum allowable length L. Take E = 200 GPa and Ix= 48.9x106 mmª & Iy=4.73x106 mm4 for W250 x 32.7. (Hint: Consider buckling in xz-plane and yz-plane separately) P W250 × 32.7 L D B x

A wide-flange shape column AB carries a centric load P of magnitude 60 kN. Cables BC and BD are taut and prevent motion of Point B in the xz plane. Using Euler's formula and a factor of safety of 2.2, and neglecting the tension in the cables, determine the maximum allowable length L. Take E = 200 GPa and Ix= 48.9x106 mmª & Iy=4.73x106 mm4 for W250 x 32.7. (Hint: Consider buckling in xz-plane and yz-plane separately) P W250 × 32.7 L D B x

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

2..Assume that the cable GBH is replaced by a cable GB only (TBH-0). So the frame ACD is supported by ball-and-socket joints at A and D and by the cable GB. You know that the frame supports at C a load of magnitude of 268 N. Find the tension in the cable GB. CopMan se reared for praticion or decay 0.925 m 0.35 m 0.5 m 0.5 m 0.875 m H 0.75 m 0.75 m
6. Three wires are used to support the 150-lb force. The wires AB and AC are made of steel, and wire AD is made of copper. Assume that the three wires have constant cross-sectional area A = 0.0123 in?. For steel wire, a = 8 x 10 in/ (in°F ) and E = 29000 ksi and for copper wire, a = 9.6 x 10 in/ (in°F ) and E = 17000 ksi. Calculate the axial force exerted by the three wires if the temperature is raised by 80°F. Answer: Pu= 10 Ib, Pu= 136 Ib 40 in. 60 in. 45°. -45° 60 in. V150 Ib
The uniform 44 kN bar BC is supported by a pin at C and the aluminum wire AB. The cross-sectional area of the wire is 178.5 mm2. Assuming bar BC to be rigid, find the vertical displacement of B due to the weight of the bar. Use E = 71 GPa for aluminum. Anwer must be in mm.
3. The rigid bar AB is supported by two rods made of the same material. If the bar is horizontal before the load P is applied, find the distance x that locates the position where P must act if the bar is to remain horizontal. Neglect the weight of bar AB. L = 3 ft A = 0.2 in.2 L = 2 ft A = 0.4 in.2 х X B 10 ft
A light ridig member AB is pinned at A and is further supported by light elastic rods CD and GF, member AB supports a 5000lb load at B the elastic modulus for the two elastic rods CD and GF is given as E= 30x106 psi and the cross-sectional area for each of these rods is 1 in2. what are the forces in the two supporting elastic rods as a results of the loading?
Two cables DAC and ACB are rolled on two pulleys at A and C as shown in Figure 2. Load Q is applied to the center of pulley C, which held in stable position shown by a force P. If the load Q = 1800 N, determine: the tension in cable ACB, and the magnitude of load P. Solve the problem mathematically by equilibrium equations. Ignore the diameter of all pulleys. А 25° D 55° C VP VQ
Rigid bars AB and BCD are supported by pins A and D and by a steel rod at C. There is a roller connection between the bars at B. E = 200 Gpa A = 300 mm2 L = 3.5 m 70 kN 2 m 1.8 m Compute the vertical displacement of point B caused by the 70 kN load. A B 1.5 m 2.5 m
Member AB (helical spring) and Member AC (axial rod) are carrying a weight at point A. Member AB has the following properties: R = 90 mm, n =4 turns, G = 70 GPa, d = 30 mm, and Tallow = 105 MPa while Member AC has the following properties: L= 2, A= 500 mm2, E 200 GPa, and oallow = 30 MPa. Determine the maximum safe value of W (in N). Use simplified formula for the helical spring.
4. Find the axial loads for all the links. Specify if the links are in tension or compression. 15,000 lb k 6 10,000 16 E D ←4▬▬★¶★ªta 4' B
The rigid bars AB and CD shown in Fig. are supported by pins at A and C and the two rods. Determine the maximum force P that can be applied if the movement of (P) is limited to 10 mm. Neglect the wieghts of all members. Aluminum L = 2 m A = 500 mm² E = 70 GPa A 3 m 3 m 3 m 0 P 3m B Steel L= 2 m A = 300 mm² E = 200 GPa D P = 153 KN P = 133 KN P = 113 KN P = 103 kN O
A steel rod is acted upon by the loading shown below. 50 mm2is the area of the circular rod. The coupling sizes at B, C, and D are neglected. Use E st = 200 GPa.
1. A safety valve spring having 9 and 2 coils has the ends squared and ground. The outside diameter of the coil is 115 mm and the wire is 13 mm. It has a free length of 203 mm. The length of which this spring must be initially compressed to hold a boiler pressure of 1.38 MPa on the seat of 32 mm diameter. Modulus of rigidity is taken as G=80GN/m?. a. Find the force acting on the valve set. b. Determine the mean diameter c. Determine the spring index d. Find the spring deflection e. Find the operating length f. Calculate the solid length g. Calculate the deflection of solid length h. Compute the solid force i. Compute the Wahl factor