Q.1) solve a b and c a) What is a phase shift oscillator?b) What is its practical application?c) Design an FET phase-shift oscillator having Ew=6000 ms, ra=36 k0, and feedbackresistor R = 12 k to operate at 2.5 kHz by selecting the values of R, C and Ro- Usethe circuit in Figure 3.1kQ16CVDD =12VRD&midR₂ C₂FHHS=2 √G RCwwwHC

The oscillation concept, which describes a periodic fluctuation between two objects based on changes…

a) What is a phase shift oscillator? b) What is its practical application? c) Design an FET phase-shift oscillator having E-6000 ms, ra=36 k0, and feedback resistor R=12 k to operate at 2.5 kHz by selecting the values of R, C and Re. Use the circuit in Figure 3. 1k02 H VDD =12V + www 1₁. RD 8mird HF C C, f= 2 √6 RC www HH C

a) What is a phase shift oscillator? b) What is its practical application? c) Design an FET phase-shift oscillator having E-6000 ms, ra=36 k0, and feedback resistor R=12 k to operate at 2.5 kHz by selecting the values of R, C and Re. Use the circuit in Figure 3. 1k02 H VDD =12V + www 1₁. RD 8mird HF C C, f= 2 √6 RC www HH C

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

In a Wien bridge oscillator circuit, resistor and capacitor form a series branch and a parallel branch. The value of the resistor is 200 ohm and the value of the capacitor is 10 mF. Determine the frequency of oscillation for the Wien Bridge oscillator circuit.
The circuit is shown below, Vin is the sinusoidal waveform with magnitude 5V and frequency is 100 Hz, R = 1 k, C = 1 uE, the chip is supplied by + 12 V source. a) What is the waveform of Yout? b) Calculate the magnitude of Vo c) If Vin is triangle waveform, what is the output waveform? -Vout , if Vin is triangle waveform with magnitude of 5 V (peak-to-peak value is 10 V) and frequency is 10 kHz, calculate waveform of you and the magnitude of I/?
D1 D V1 D4 D2 V D D Diode Model: 1N5817 R = 10k Vi= sine (0 5 100) Given the parameters above, simulate the given circuit using .tran 0 30m 0. Solve for the output peak to peak voltage across the resistor and the output frequency measured across the resistor. Output Frequency = (When computing for the frequency, use 4v as reference point) Output Voltage (pk-pk) = + R1 R D3 D
Vdc please show the circuit in the figure as a Chaotic Oscillator. Show it using one of the simulation programs. You can make any changes you want. m
Q2. Find Q-point when VBB = 1V, 2 V and 3 V.. Assume VCE(sat) = 0 V. Re 1.0 KO Vcc RB www Bpc = 50 20 kN Draw the output waveform for the circuit shown below
Q3( (A) Consider you have to analyze a Step-Down DC convertor having the following parameters: Input DC voltage - 24 V, Duty Cycle-0.65, L-20 μH, C = 15 μF, and R = 102. The switching frequency of IGBT/MOSFET Switch is 150 kHz. Analyze the above convertor for the following: a) The output voltage of the convertor b) The maximum and minimum inductor currents. c) The percent ripple in output voltage. (B) The full-bridge inverter of has a switching sequence that produces a square wave voltage across a series RL load. The switching frequency is 60 Hz, Voc-100 V, R=10. and L=25 mH. The power absorbed by load is 440 W. Analyze the above invertor for the following: (a) an expression for load current, (b) Average current in the DC source.
Q.2/ Find the value of R2 in figure below so that the circuit will oscillate. Q.3/ For the circuit shown below, find Rf if rds for the JFET is 350 ohms when oscillation is stable. Q.4/ Find Rf and fr: Q.5/ How to change the frequency of oscillation of the following circuit to 10kHz? Q.6/ Modify the sawtooth generator in figure below so that its peak-to-peak output is 4V. Is it aVCO? Q.7/ To what value must Cext be changed in figure below to achieve a frequency of 25kHz?What is the benefit of C1? Can be neglected? Q.8/ What is the crystal oscillator? Explain its principle of operation. Explain how to connect a crystal with frequency of 10MHz to a microcontroller?
What type of A/D converter would work best for video signals with a frequency content up to 5 MHz? Why? (Our subject is Principles of Electronic Communications)
If ADM = 3500 and ACM = 0.35, the CMRR is ..........
An op-amp comparator in a firing circuit can produce waveforms at the output of up to 20 V peak-to-peak without any distortion. An inverse cosine-based firing circuit with a voltage range from +10 to -10 (reference voltage) is used to produce a gating signal for the SCR at the desired delay angle. if the reference voltage is -5.01 volts, the delay angle (in degrees) would be: O A. None of the other choices are correct O B. 150 O C. -120 O D. 120 O E. 60
What is an A/D converter with Voltage-to-Frequency Conversion (VFC)? What is the working principle?
1- Mention any two advantages of Integrated Circuit . 2- For the circuit given below : Vin is a sine wave Vinpp=6 V and Vref=-2.4 V , Assume Vsat=±12V Name the circuit and draw the input and output waveforms . Vin Vref 3- Explain why open-loop op-amp configurations are not used in linear applications? Draw the block diagram of opamp and define the function of each block