A water pump produces a flow of 8 ft" /s and a power of 4 hp, using an 11-in.-diameter impeller. Part A What is the flow if a 6-in.-diameter impeller is used to maintain dynamic similitude? Express your answer using three significant figures. ft /s Q = - Part B What is the power if a 6-in.-diameter impeller is used to maintain dynamic similitude? Express your answer using three significant figures. W = hp

A water pump produces a flow of 8 ft" /s and a power of 4 hp, using an 11-in.-diameter impeller. Part A What is the flow if a 6-in.-diameter impeller is used to maintain dynamic similitude? Express your answer using three significant figures. ft /s Q = - Part B What is the power if a 6-in.-diameter impeller is used to maintain dynamic similitude? Express your answer using three significant figures. W = hp

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

LR = 5m, LG = 2.5m and LC = 1.1m Q2. The Skylark family of sounding rockets consisted of a number of variants (denoted Skylark 5, Skylark 7, and Skylark 12 respectively). These are illustrated on Page 3. The data given below is based on that for the rocket motors they used (all manufactured and named by what was Royal Ordinance – now part of Roxel): Raven XI Motor Total mass: 1280 kg Length = LR See Case Table (units are m) Diameter = 0.44 m Goldfinch IIA Motor Total mass: 420 kg Length = LG See Case Table (units are m) Diameter = 0.44 m Cuckoo IV Motor Total mass: 242 kg Length = LC See Case Table (units are m) Diameter = 0.44 m The payload mass which is additional to the motor masses is to be taken as 100 kg. (a) For the configurations of the three rockets shown on Page 3 in Fig. Q2: (i) Determine the Pitching/Yawing moment of inertia of each rocket about the base of each rocket. (ii) Explain how you could then find the the Pitching/Yawing moment of inertia of each rocket about its…
Find : The acceleration (in m/s^2) of cylinder C.
5. A tank contains two substance oil (A) and water (B) subject to variable air pressure; the dimension is shown below and corresponds to 1atm. If air is slowly added from a pump to bring pressure p up to 1MPA gage, what will be the total downward movement of the free surface of oil and air? Take average values of bulk moduli of elasticity of the liquids as 2050MPA for oil and 2075MPA for water. Assume the container does not change volume. Neglect hydrostatic pressures. Air 200 mm 600mm Oil- Water 700 mm 300 mm
Assume that annual energy requirement of an industry is 20000 kWh . DETERMINE size of wind turbine that is required to be installed to meet the energy requirement . Following assumptions are taken into account for estimation Annual energy requirement - 20000 kWh Propeller type wind machine is used . Coefficient of performance -0.40 Wind speed at 15 meter height is 5 meter / sec ( if the turbine hub is placed at the height other than 15 meter , the wind speed should be estimated as shown in " vertical wind speed variation section Density of air - 1 kg / m Capacity factor -0.30
a. CH, CQ and  are functions of CP. Draw the dimensionless performance curves of the turbine on a single graph by makingthe necessary scalings. (Fit the curve by using the excel program for drawing. Also give the values you used for plotting inthe table) b. Find the efficiency of the model at the most efficient operating point and the coefficients of head (CH), flow (CQ) and power(CP). Show them on the graph you have drawn. c. Calculate the diameter, net head, number of revolutions (rpm), flow rate, power (MW) and modified efficiency of theprototype d. Determine the turbine type ÖN number is 5
Please solve! Find the air horsepower of an industrial fan that delivers 55 000 cubic feet of air per minute through a 3 ft. by 4 ft.; pressure is 5 in. of water; air temperature is 700 F and barometric pressure is 29.92 in. of mercury.
E Reading list ogle Mee Use g =9.81m/s2. A 2m diameter open cylindrical tank, half-filled with water, is rotated about its vertical axis. If the height of the tank is twice the diameter, determine the following: the maximum speed (rpm) without spilling any water; the height (m) of water at the sides of the tank if the depth of water at the center is zero; the vertical distance (m) of the vertex of the parabola from the top of the tank if the angular speed is 90rpm; and the volume of water spilled (in liters) if the angular speed is 90 rpm. Note: Do not include units in your answers. Do not round off intermediate values and answer in four decimal places. 600 pm
1) From 0 to 10 sec, find alphaA1, alphaC1 in rad/s^2, omegaA1(t), omegaC1(t) in rad/s, thetaA1(t), thetaB1(t) and thetaC1(t) in rad, and the distance made by the load s1 in inches and in feet made by the load during this time.
Question 7 Convert the gravitational acceleration g = 9.8 m/s2 to (ft/s?). g = ft/s?
THERMODYNAMICS UPVOTE WILL BE GIVEN. PLEASE WRITE THE COMPLETE SOLUTIONS/DIAGRAMS LEGIBLY. NO LONG EXPLANATION NEEDED. USE 3 DECIMAL PLACES. BOX THE FINAL ANSWER. A pump discharges into a semi spherical tank at the bottom and cylindrical on top with a radius of 2 meters, and a total tank height of 8 meters. The flow rate is 80 gallons per minute and fluid specific gravity= 1.1. Determine the following: A) flow rate in kg/sec and time it takes to fill the tank in hours. Flow Rate and Time
THERMODYNAMICS UPVOTE WILL BE GIVEN. PLEASE WRITE THE COMPLETE SOLUTIONS/DIAGRAMS LEGIBLY. NO LONG EXPLANATION NEEDED. USE 3 DECIMAL PLACES. BOX THE FINAL ANSWER. A pump discharges into a semi spherical tank at the bottom and cylindrical on top with a radius of 2 meters, and a total tank height of 8 meters. The flow rate is 80 gallons per minute and fluid specific gravity= 1.1. Determine the following: A) flow rate in kg/sec and time it takes to fill the tank in hours. B) the weight in tons of the liquid if full tank local gravity is 32.1 ft/sec squared. C) volume of the tank in metric gallons. D.) how many drums will be needed to transfer all of the tank contents (tank being full) to the drums?
7. A tire gauge registers 32 lbs/in2 when air in a certain tire is at 10°C. After running for a time, the tire heats up to 30°C. Calculate the pressure that would be registered then by the gauge. Complete FBD, FORMULA, AND SOLUTION