A vertical cylindrical, wooden-stave barrel is 3.5 ft in diameter and 5 ft high, and is open at the top. It is held together by steel hoops at the top and bottom, each with a cross section of 0.40 in². Let T₁ and T₂ be the tensile forces in the top and bottom hoops, respectively, and ₁ and ₂, the stresses in the top and bottom hoops, respectively. If the barrel is filled with orange juice (SG = 1.04), determine the following: (a) The total hydrostatic force, F (lb) exerted by the orange juice on the walls of the tank. (b) The total pressure (psi) at the bottom of the tank. (c) The tensile force T₁ (lb) at the top hoop (d) The tensile force T₂ (lb) at the bottom hoop

A vertical cylindrical, wooden-stave barrel is 3.5 ft in diameter and 5 ft high, and is open at the top. It is held together by steel hoops at the top and bottom, each with a cross section of 0.40 in². Let T₁ and T₂ be the tensile forces in the top and bottom hoops, respectively, and ₁ and ₂, the stresses in the top and bottom hoops, respectively. If the barrel is filled with orange juice (SG = 1.04), determine the following: (a) The total hydrostatic force, F (lb) exerted by the orange juice on the walls of the tank. (b) The total pressure (psi) at the bottom of the tank. (c) The tensile force T₁ (lb) at the top hoop (d) The tensile force T₂ (lb) at the bottom hoop

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The solid cylinders AB and BC are bonded together at B and are attached to fixed supports at A and C. Knowing that the modulus of rigidity is 3.7E6 psi for aluminum and 5.6E6 psi for brass, determine the maximum shearing stress in cylinder AB And cylinder BC in ksi. 1 Aluminum T= 19.6 kip-in. Brass A - 1.4 in. B <-2.1 in. C 10 in. 15 in.
The bar of the pin connected frame shown are each 30mm by 60mm in section. determine the maximum load P that can be applied so that the stress will not exceed 100MN/me in tension or 80 MN/me in compression
Two plate are joint by five rivets of 20 mm diameter. What is the shear stress in the material if the shear forces is 18840 N O 12 N/mm2 O 20 N/mm2 O 15 N/mm2
2.47 The negligible weight rigid bar is pinned at O and attached to two vertical rods. WI is the largest load P that can be applied without exceeding stresses of 150 MPa in t steel rod and 70 MPa in the bronze rod, assuming the rods were initially stress-free? 4m 3m 3m Steel A = 600mm2 E = 83Gpa L = 4m Steel V P A = 1800mm2 E = 200Gpa L 3m
3. The rigid bar weighs 5 kN/m, is supported as shown. The assembly is initially stress-free. Find the stress in each rod if the temperature rises 20°C after a load W = 150 kN is applied. A (mm?) a (FC) E (GPa) Steel rod 300 11.7 x 10-6 200 Bronze rod 1400 18.9 x 10-6 83 Bronze | 3 m Steel 1.5 m ►| 1.0 m 2.5 m 2 m W
2. Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. What is the stress in each material given that P = 10 kN? Specify whether tension or compression. Bronze Aluminum Steel A =400 mm2 A= 600 mm2 A = 300 mm2 2P ЗР 4P P -3 m 5 m 4 m Stress in Bronze (MPa) %D Stress in Aluminum (MPa) %3D Stress in Steel (MPa)
The horizontal bar ABC is supported by a pin at A and two rods with identical cross- sectional areas. The rod at B is steel and the rod at C is aluminum. Neglecting the weight of the bar, determine the force in each rod when the force P = 80 kN is applied. Use Est = 200 GPa and Eal = 70 GPa. %3D Steel Aluminum A B T2 m- 1.5 m- Im
Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. What is the stress in each material given that P = 15 kN? Specify whether tension or compression. Bronze Aluminum Steel A=400 mm? A=600 mm? A= 300 mm? 2P 3P 4P P -3 m + 5 m -4m
Determine the normal stress (in Mpa) in member AB of the truss shown if it is made up of a 14-mm-square bar of alloy and the load P is 21.53 kN. Express your answer in two decimal places.
1. The assembly is shown is attached to supports at A and D. Section BCD is a solid 2" diameter aluminum [E = 10,000 ksi] rod. Steel [E = 30,000 ksi] tube AB has an outer diameter of 3.50" and a wall thickness of 0.216 in. Determine (a) the stresses is sections AB, BC and CD, and (b) the deflections of joints B and C. [OAB = 3.40 ksi (C), Osc = 5.863 ksi (T) Oc, = 4.959 ksi (C), 8, = 0,0054"– , d. = 0,02975"→] %3D %3D %3D %3D 13 kips 17 kips A C 13 kips 17 kips 4 ft 5 ft 5 ft
When the temperature is at 30°C, the steel pipe fits snugly between the two fuel tanks. When fuel flows through the pipe, it causes the temperature to vary along the pipe as T = (3x² 20x + 120)°C. Calculate the normal stress developed in the pipe. Assume each tank provides a rigid support at A and B. a=12X10-6/°C - 150 mm 10 mm- Section a - a -6 m a a B
Determine the force P necessary to close the gap at the steel post. The steel post is 2 inch x 2 inch square and 8 in high. The aluminum alloy bar is 1.5 inch wide by 1 inch thick and 20 in long. The horizontal bar is considered rigid as are the loading caps at the steel post. The modulus of elasticity for the steel is 30,000 ksi, that of aluminum is 10,000 ksi. The yield stress for the steel is 36 ksi, that of the aluminum is 40 ksi. 8" 10" Steel 10" Rigid Aluminum 20 inches long * P 10" Gap = 0.02 inches