A tube is used as a siphon to discharge an oil of specific gravity 0.8 from a large open vessel into a drain at atmospheric pressure as shown in Fig the velocity of oil through the siphon, (ii) the pressure at points A and B,(iii) the pressure at the highest point C.(iv) the maximum height of C that can be accommodated above the level in the vessel, and (v) the maximum vertical depth of the right limb of the siphon. (Take the vapour pressure of liquid at the working temperature to be 29.5 kPa and the atmospheric pressure as 101 kPa. Neglect friction) Q3) . Calculate (i) 2.5 m 2.5 m B H 5.0 m

A tube is used as a siphon to discharge an oil of specific gravity 0.8 from a large open vessel into a drain at atmospheric pressure as shown in Fig the velocity of oil through the siphon, (ii) the pressure at points A and B,(iii) the pressure at the highest point C.(iv) the maximum height of C that can be accommodated above the level in the vessel, and (v) the maximum vertical depth of the right limb of the siphon. (Take the vapour pressure of liquid at the working temperature to be 29.5 kPa and the atmospheric pressure as 101 kPa. Neglect friction) Q3) . Calculate (i) 2.5 m 2.5 m B H 5.0 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A venturi meter with a throat diameter of 100 mm is fitted in the inclined pipeline of 200 mm diameter with oil of specific gravity 0.88 flowing upwards. The venturi meter coefficient is 0.96. Two pressure gauges are fitted at tapping points, one at the throat reads the vacuum pressure of 40 cm of mercury and the other in the inlet pipe 320 mm below the throat is 20.231 N/cm2. If the loss of head in the main and throat is 0.35 times the kinetic head of the pipe, determine2.1 the volume flow rate of oil through the pipe2.2 the difference in level in the two limbs of the mercury manometer if it is connected to the tapping points and connecting pipes are filled with the same oil
A pipe carrying oil of sp gr 0 877 changes in A pipe carrying oil of sp gr 0.877 changes in size from 150mm at section E to 450mm at section R Section E is 3 66m lower than R section R. Section E is 3.66m lower than R and the pressures are 91.0kPa and 60.3kPa, respectively. If the discharge is 0.146m3 respectively. If the discharge is 0.146m /s, determine the lost head and the direction of flow.
2. A discharge of 8.5 L/s of oil having a sg=0.8 occurs through the venturi shown. The diameter of the pipe is 37.5 mm while that of the throat is 25 mm. The liquid in the differential gage shown contains mercury sg = 13.6 and the rest is filled with oil 37.5 mm A) Find the velocity at the throat (7.7 m/s) B) Compute for the value of h1 (0.8125 m) C) Compute for the value of h2 (0.238 m) oil mercury 25 mm h1 37.5 mm h2
At point A where the suction pipe leading to a pump is 2. 50 meters below the pump an open manometer indicates a vacuum of 9 in. of mercury. The pipe is 125 mm in diameter, the discharge is 35 liters per second of oil (sp. gr. = 0. 80). Compute the total head at point A with respect to a datum at the pump.
A U-tube manometer is connected to a pipe for measuring the pressure of oil (Specific gravity 0.92) flowing in the pipeline. Mercury (Specific gravity 13.6) is used as manometer liquid and the difference of mercury level in the two limbs is 200 mm. The centre of pipe is 80 mm below the level of mercury in the right limb. Determine the pressure in the pipeline and the head. | 80 mm 100 mm
For the pipe enlargement shown, the pressure at sections (1) and (2) are 56.3 and 58.2 psi, respectively. Determine (Gasoline density=1.32 slug/ft³) a. The Velocities at section 1 and section 2. b. The flow rate (Q) of the gasoline in the pipe. 2.05 in. (1) Gasoline 3.71 in.
1) Determine the flow in Ips on the orifice between the 2 tanks shown below AIR 25kPa AIR 10kPa OIL S=0.80 OIL S=0.80 WATER WATER ORIFICE C0 60 D-50mmo 2,8m 2m 1.5m WL
The rectangular tank shown is divided by a partition into two chambers,and provided with a round 150mm diameter sharp-edged orifice at the lowerportion of the partition. At a certain instant, the level in chamber B is 3mhigher than it is in chamber A. How long will it take for the water surfaces inthe two chambers to be at the same level? Assume C =0.62.
Situation 1: In the pipe system shown, the velocity of water in pipe A is 1 m/s. The friction factor f = 0.02 for all pipes. a. Determine the discharge in pipe B. b. Determine the velocity in pipe C. c. Determine the headloss in pipe E. d. Determine the difference in elevation of the two reservoirs. Water D A 300 m 200 mm D 300m 500 mm Diom 600m 300mm Diam 300m 300mm D B 800 m 300mm Diam E
A tube is used as a siphon to discharge an oil of specific gravity 0.8 from a large open vessel into a drain at atmospheric pressure as shown in Fig . Calculate (i) the velocity of oil through the siphon, (ii) the pressure at points A and B,(iii) the pressure at the highest point C,(iv) the maximum height of C that can be accommodated above the level in the vessel, and (v) the maximum vertical depth of the right limb of the siphon. (Take the vapour pressure of liquid at the working temperature to be 29.5 kPa and the atmospheric pressure as 101 kPa. Neglect friction) Q3) 2.5 m 2.5 m H 5.0 m to
1. Gasoline (sp. gr. 0.8) is flowing upwards a D, 150 mm vertical pipeline which tapers from 300 mm to 150 mm diameter. A gasoline mercury Outlet differential manometer is connected between 300 mm and 150 mm pipe section to measure the rate of flow. The distance between the manometer tappings is 1 metre and gauge reading is 500 mm of mercury. Find: 1) Differential gauge reading in terms of gasoline head; Gasoline (Sp. gr. = 0.8) 2) Rate of flow. Neglect friction and other losses between tappings. Inlet D, 300 mm 1 m
11. From the figure shown, the tank contains oil having a sg = 0.82. Oil flows at a certain rate which produce power in the jet equal to 9 hp. Diameter of orifice is 80 mm with Cv = 0.96 and Cc = 0.62 A) Compute the velocity in the jet. B) Compute the gage reading at B. C) Compute the rate of discharge. 11A v = 11.57 m/s 11B P = 113.88 kPa 11C Q = 0.056 m³/s 2.8 m Air Oil 0.82 B