A Truck in which the pair of wheels at the rear side carries a load of 1.5 Tonnes on each axle box, acting at a distance of 150 mm outside the wheel base. The distance between the wheel base is 1.8m. Find the diameter of the axle between the wheels, if the stress is not to exceed 100 N/mm².

A Truck in which the pair of wheels at the rear side carries a load of 1.5 Tonnes on each axle box, acting at a distance of 150 mm outside the wheel base. The distance between the wheel base is 1.8m. Find the diameter of the axle between the wheels, if the stress is not to exceed 100 N/mm².

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A cube is floating in oil (sg = 0.9). The sides of the cube are 100 mm and it is floating 75 mm deep…

Q: A centrifugal friction clutch has a driving member consisting of a spider carrying four shoes which…

A: To find: The mass of the shoes and the size of the shoes. Given: R = 150 mm. r = 125 mm.μ = 0.25.n…

Q: A pipe handles a flow rate of 0.002 m³/s. Find the minimum inside diameter that will provide an…

Q: 9. The radial reaction of bearing B is calculated as 30000 N. Considering the dynamic load rating of…

A: Given data: P=30000 NC=90000 N n=3

Q: ||-a- -2a- -2a- -2a- O10979.88 x 104 mm4 O 3229.29 × 104 mm4 7076.89 x 104 mm4 O9671.69 x 104 mm4 O…

Q: 0.75 in I 1.75 in 2.25in -> 4.75in --> X -> Find the MOI of the Above Shape with Jespect to It's…

Q: What type of differential equation is the clapeyron-Clausius equation ?

Q: Question 2 A crane hook has a trapezoidal section at A-A as shown in Figure 2. Find the maximum…

A: Given

Q: Select the most suitable choice: i) The process of addition nitrogen to a carbourizing case, known…

A: 1. Nitriding process 2.cold working, spherodising process 3. Strong in tensile strength and…

Q: 9 Water is pumped from a lake to a storage tank 18 m above at a rate of 70 L/s while consuming 20.4…

A: Given : head of water supply h = 18m flow rate of water Q = 70 L/s (since 1 Litre = 10-3 m³) ∴ Q =…

Q: Find solutions for the divergence and curl of the vector field y at (1, 0, -1). v (x, y, z) = x²z²į…

A: The vector field is V=x2z2i⇀+xyzj⇀+zcosy4k⇀. The position is (1,0,-1) The divergence is ∇·V is the…

Q: A piezometer and a Pitot tube are tapped into a horizontal water pipe, as shown in Figure below, to…

A: Given:h1=3 cm=0.03 mh2=7 cm=0.07 mh3=12 cm=0.12 mFind:The velocity at the center of the pipe, V1

Q: Consider the given state of stress. Given: X= 6 ksi and Y= 30 ksi. + 6 ksi

A: Given:Stress along X-axis, σx=6 ksiStress along y-axis, σy=30 ksiShear stress, ζxy=6 ksi

Q: 4. For the beam and loading shown, (a) draw the shear and bending-moment diagrams, (b) determine the…

Q: 2/38 As a trailer is towed in the forward direction, the force F= 120 lb is applied as shown to the…

Q: A large regenerative steam turbine having a stage efficiency in the vapor state is at 64.56%. The…

A: Givenηvapour stage=64.56%ηblade=90%ηmoisture=2.87%ηloss=3%

Q: 4-26 Steel rods (p = 7832 kg/m³, c, = 434 J/kg-K, and k = 63.9W/m-K) are heated in a furnace to…

A: Given Thermal conductivity, k = 63.9 W/m.K Heat transfer coefficient, h = 650 W/m2K…

Q: Determinethecapacityoftheheatingcoilwhen1.5m3/sofmoistairis heated from 21C db, 15C wb with a…

A: Given: Flow rate of moist air: →Q=1.5 m3/s Hot water entering temperature: →T1=85°C Hot water exit…

Q: A flashed-steam geothermal power plant is located where underground hot water is available as…

Q: Q3: A simply supported beam AB of length 6 m subjected to a clockwise couple of 24 point C as shown…

Q: A petroleum liquid with (SG = 0.83), flows through the Venturi meter as shown with flowrates between…

A: Given:Specific gravity of liquid, s=0.83Velocity of liquid at point 1, v1=4 L/sVelocity of liquid at…

Q: Forces are applied at points A and B of the solid cast-iron bracket shown. The bracket has a…

Q: Determine the heat-transfer rate from an electronic chip whose surface temperature is 31ºC and has…

Q: A flashed steam geothermal power plant has pressurized underground water available at 102 kg/cm2 and…

Q: Brinell hardness tests were made on a random sample of 10 steel parts during process- ing. The…

A: Given HB values are 230, 232(2), 234, 235(3), 236(2), 239 For steels, the relation between Brinell…

Q: an automobile uses 80.5 kw to maintain a uniform speed of 90 kph. what is the trust force provided…

Q: Given: V = 30 m/s, u = 12 m/s, alpha = 30°. D Select one: O a. 45° O b. 47° O c. 43°

A: GivenV=30m/su=12m/sα=30o

Q: A pinion with a unity diametral pitch, 22 teeth, has a pressure angle of 20 degrees and full-depth…

A: Given data: T=22 teethϕ=20°

Q: I need the final answer only. A steam turbine operating at 5Mpa, 400C( h = 3195.7 KJ/kg) has an…

Q: What is (or define) Reynolds Number? state the purpose of using the number?

A: Purpose of Reynolds No: the purpose of the Reynolds no is to predict the flow patterns in various…

Q: Pls i need answer asap. Fluid Mechanics: A piece of Ore weighing 2 N in air is found to weigh 1.216…

A: (a) Write the given data. W=2 NWsubmerged=1.216 Nγw=9800 N/m3

Q: A 15kg sample of water is held at 200°C in a variable-volume container (a piston-cylinder…

A: Given: Mass of the sample→m=15 Kg Sample of the temperature→T=200°C Specific volume of the…

Q: What is the payback time on a solar hot-water system that cost$ 5,000? Assume the system reduces…

A: To find: The payback time. Given: The cost of the solar hot-water system is Cs=$5000=500000 cents.…

Q: Question/ Do a small research about the types of condensers in powerplant.

Q: The water tank shown below is being filled through section 1 at U1 =3 m/s and through section 3 at…

Q: Applications to DE law of cooling According to Newtons law of cooling, the rate at which a…

Q: T 1.56 2.56 -262626 -b -3b 26 x

Q: Air passes through a pipe 30 mm in diameter and 1.5 m long. The pipe frictio is 0.003. At the pipe…

A: The pressure relation for the isentropic flow is PtP=1+γ-12Mγγ-1 The pipe friction factor is…

Q: A. A tensile stress (♂) is applied to a single crystal. The angle between the direction of the…

Q: A solid object with hemispherical bottom floats in a liquid (s = 1.25) with 100 cm projecting above…

Q: Determine the force in each member of the loaded truss. Make use of symmetry of the truss and of the…

A: Given data,…

Q: A body falls from rest against a resistance proportional to the velocity at any instant. If the…

Q: 3. Draw the shear and moment diagrams for the figures shown Figures (C and D)

Q: A four bar mechanism PQRS with link PS fixed. The length of the links are PQ=4cm, QR=9cm, RS=5.5 cm…

A: Given: A four bar mechanism PQRS with link PS fixed. The length of the links are PQ=4cm, QR=9cm,…

Q: The Free-Body diagram for joint C is drawn assuming that all internal forces are in tension. Solve…

A: Given:Load acting at point D, P=2660 N

Q: Q2: A beam ABCDE is 7 m in length and loaded as shown in Figure. Draw the S.F. Al and B.M. diagrams…

Q: QUESTION The temperature profile in a 10 cm solid wall is given by T(x) = 1000-100 x + 2000x where r…

A: (a) Write the given data. t=10 cmTx=1000-100x+2000x2ρ=1600 kg/m3cp=4000 J/kgKk=10 W/mK

Q: Part A: Find the steady-state solution of the mechanical system shown below: k HE E X F(0) F(t) = F…

A: The steady-state solution means a solution that is independent of time., it doesn't vary with time.…

Q: Three cables are joined at the junction ring C. De- termine the tensions in cables AC and BC caused…

Q: why did you neglect pressure at section 2? shouldn't that be taking into account when using the…

A: Given:Diameter at section 1, D1=0.1 mDiameter at section 2, D2=0.065 mVelocity at section 2, V2=2…

Concept explainers

General safety guidelines

Safety guidelines are the set of rules and codes that must be followed in the workplace for the occupational safety of workers, the machines, and the equipment that are present inside the workshop premise. There are many unsafe conditions and hazardous materials inside the workshop that makes prey for certain risk factors associated with health conditions. Extreme safety precautions must be taken inside the work area just like the precautions and practices that are been followed for Corona Virus Disease 2019 (COVID-19). People can also educate themselves by joining various health programs and camps. These will provide them with the necessary skills and knowledge about safety awareness. Occupational Safety and Health Administration (OSHA) thrives to create a safe and healthy environment for the workers working in the industries and provides them with proper education and training.

Question

A Truck in which the pair of wheels at the rear side carries a load of 1.5 Tonnes on each axle box,
acting at a distance of 150 mm outside the wheel base. The distance between the wheel base is
1.8m. Find the diameter of the axle between the wheels, if the stress is not to exceed 100 N/mm².

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The lap joint shown is fastened by five ¾ inch-diameter rivets. The bearing stress in the plates is limited to 10 ksi and the shearing stress in the rivets is 15 ksi. Assume the applied load is equally distributed among the five rivets. The thickness of each plate is ½ in. Calculate the load P based on each stress given. Determine the maximum safe load P that can be applied. Express the loads in kips.
Two loads P act as shown, one parallel to x and another parallel to z axes; each load P equals 1850 N. The crankshaft dimensions are b1 = 85 mm, b2 = 130 mm, and b3 = 60 mm. The diameter of the upper shaft is d = 28 mm. Determine the normal stress at point B, which is located on the surface of the upper shaft at the y axis. Lütfen birini seçin: a. 121.465 MPa b. 287,937 MPa O c. None O d. 149.606 MPa e. 324.676 MPa
The heels on a pair of women's shoes have a radius of 5 cm at the bottom. If 30% of the weight of a woman 480N is supported by each heel, find the stress on each heel
Determine the resultant internal loadings acting on the cross section at B of the pipe shown. End A is subjected to a vertical force P and a horizontal force Q. Use P = 90 N and Q = 70 N. a. Determine the internal axial force (in N) in section B. b. Determine the internal shear force (in N) in section B. c. Determine the internal torque (in N-m) in section B. With FBD please thank you.
inches, determine the mass of the heaviest cylinder. Neglect friction and the weight of the rigid bar AB A uniform cylinder is supported by a rigid bar AB and cable BC as shown in the figure. If the stress in the cable is not to exceed 7.25 ksi and diameter of 0.50 18 Ft B 18 Ft 12 Ft
A crane is supported by two cables with a cross-sectional area of 3.04 cm2 each. Determine the amount of stress on each cable.
Assignment 1 A 175-lb woman stands on a vinyl floor wearing stiletto high-heel shoes. If the heel has the dimensions shown, determine the average normal stress she exerts on the floor and compare it with the average normal stress developed when a man having the same weight is wearing flat-heeled shoes. Assume the load is applied slowly, so that dynamic effects can be ignored. Also, assume the entire weight is supported only by the heel of one shoe. 1.2 in. 0.5 in. MR. KYEKYERE ERNEST 0.3 in. --0.1 in. Intro to Basic Mechanics July 18, 2022 20/78
Determine the largest weight “W” that can be supported by the two wires AB and AC. The working stresses are 100MPa for AB and 150MPa for AC. The cross sectional area of AB and AC are 400mm2 and 200mm2 Compute “W” due to the stress capacity of AB Compute “W” due to the stress capacity of AC. Determine the safest value of “W”.
An aluminum wire 3.0 m in length and 4.0 mm in diameter supports a 1000 N mass. Determine the stress in the wire.
2. A hollow iron pipe with outside diameter of 240 mm is used as a column to carry a load of 80 kN. Determine the pipe thickness if the compressive stresses is limited to 16 MPa.
2m 9. The rod AB rests on a horizantal surface at A and against slipping suface at B if Ms =0-25 at A&B. Find the minimum distance a for equilibriam, negledt the weight ( Ans a-l-6lm) a 60N • peu m7 jo
To avoid interference, a link in a machine is designed so that its cross-sectional area is reduced one half at section A-B as shown below. If the thickness of the link is 50 mm, compute the maximum force P that can be applied if the maximum normal stress on section A-B is limited to 80 MPa.